There exist many kinds of frictions in internal combustion engine such as piston ring and skirt, cam and tappet, bearing friction etc. Among them, the frictions between piston ring, skirt and cylinder are particular. These frictions for motoring test are differ from that of firing test even though the temperature of cooling water and lubricating oil keep identically. The frictions for firing test are increased due to combustion pressure and products. The precise calculation of the friction is difficult. But we can assume that the friction is governed by the viscosity of lubricating oil and gas pressure of cylinder. And the viscosity of lubricating oil is dependant on gas temperature of cylinder, so the piston friction may be governed by gas pressure and temperature of cylinder. In this treatise, we propose the method of evaluating piston friction under the condition of constant engine speed, and we analyzed the behaviours and influence of factors concerned with the piston friction for output correction when the inlet pressure and temperature were varied. The main results are as follows: 1) The behaviours on the inlet conditions for the contact force of the piston rings and the viscosity of the lubricating oil concerned with piston friction are found. 2) The essential point the these behaviours is dependant on the cyclic variation following to the inlet conditions. 3) According to our analysis, It was observed that the viscosity of lubricating oil is more effective than the contact force to the piston rings.
Seismic isolated building structures are examined in this study. The triple concave friction pendulum (TCFP) is used as a seismic isolation system which is easy to be manufactured and enduring more than traditional seismic isolation systems. In the TCFP, take advantage of weight which pendulum carrying and it's geometry in order to obtain desirable result of seismic isolation systems. These systems offer advantage to buildings which subject to severe earthquake. This is result of damping force of earthquake by means of their internal constructions, which consists of multiple surfaces. As the combinations of surfaces upon which sliding is occurring change, the stiffness and effective friction change accordingly. Additionally, the mentioned the TCFP is modeled as of a series arrangement of the three single concave friction pendulum (SCFP) bearings. A two dimensional- and eight- story of a building with and without isolation system are used in the time history analysis in order to investigate of the effectiveness of the seismic isolation systems on the buildings. Results are compared with each other to emphasize efficiency of the TCFP as a seismic isolation device against the other friction type isolation system like single and double concave surfaces. The values of the acceleration, floor displacement and isolator displacement obtained from the results by using different types of the isolation bearings are compared each other. As a result, the findings show that the TCFP bearings are more effective devices for isolation of the buildings against severe earthquakes.
흙채움 마대는 현장의 재료를 사용하여 간편하게 사면 및 제방의 복구나 보강에 사용되고 있다. 이런 흙채움 마대의 전단저항력을 증가시키기 위해 흙채움 마대 상 하면에 벨크로(Velcro)를 부착한 흙채움 마대가 개발되었으며, 벨크로를 부착한 흙채움 마대의 역학적 특성을 분석하기 위해 대형직접전단실험과 원호파괴를 가정한 실내모형실험이 수행되었다. 실제 벨크로가 부착된 마대를 이용해 사면을 설계하기 위해 흙-토목섬유 요소실험을 실시하여 강도정수를 파악하였다. 그리고 사면형성 시 벨크로와 흙채움 마대가 혼재하고 있기 때문에 정확한 파괴면을 알 수 없다. 따라서 실내모형실험을 통해 내적파괴에 대한 거동을 분석하고, 역해석을 통해 설계강도정수를 제안하였다. 흙-토목섬유의 요소실험결과, 벨크로의 부착으로 인해 흙채움 마대 상호간의 전단저항 정수인 내부마찰각과 점착력의 증가가 나타났으며, 특히 내부마찰각보다는 점착력의 뚜렷한 증가가 나타난 것으로 분석되었다. 또한, 실내모형실험 결과, 지지력이 20%이상 증가해 대형장비의 주행성 증가와 시공속도의 증대를 가져올 것으로 판단된다.
이 연구는 구조물 내진보강 장치의 하나인 마찰댐퍼에 관한 것으로, 내부 마찰재를 복합재료의 일종인 초고분자량 폴리에틸렌으로 대체하여 댐퍼를 개발하였다. 또한 마찰력이 발생하는 내부 구조를 여러 층으로 적층하는 다중 마찰방식을 적용하였다. 개발된 다중 마찰댐퍼의 성능 검증을 위해서 재료에 대한 기초 물성과 마모 특성, 디스크 스프링에 대한 특성 분석 시험을 수행하였다. 마모시험 시험결과, UHMWPE의 질량 감소율은 0.003%로 복합재료 기반의 마찰재 중에서 가장 우수한 성능을 보였다. 디스크 스프링은 유한요소해석과 시험결과로부터 설계기초자료를 확보하였다. 또한 개발된 다중 마찰댐퍼의 품질 안정성을 확인하기 위해 토크값에 따른 마찰력 변화와 감쇠장치에 대한 지진하중 시험을 수행하였다. 품질성능 시험결과, 토크 값 조절에 따라 선형적인 마찰력 변화를 보였으며, 지진하중 시험 결과, 마찰댐퍼의 허용오차는 설계기준에서 요구하는 15% 미만으로 나타나 내진보강 장치로서의 요구조건을 만족하는 것으로 나타났다.
본 연구에서는 지반공학 및 지질공학적 측면에서 단층핵의 거동을 이해하기 위해 화강암, 퇴적암 및 화산암 단층대에서 채취된 단층핵 시료를 대상으로 물리적 특성(각력 및 점토함량, 단위중량, 공극률, 함수비)과 마찰 특성(내부마찰각, 점착력)의 관계를 분석하였다. 실내시험으로부터 산정된 물리적 특성을 분석한 결과, 단층핵 내 각력은 단위중량과 양(+)의 상관관계를 가지고, 점토함량, 공극률 및 함수비와는 음(-)의 상관관계를 가진다. 직접전단시험으로부터 산정된 내부 마찰각과 점착력에 대한 사분위수 범위(IQR)는 각각 16.7-38.1°, 2.5-25.3 kPa로 나타났다. 또한, 단층핵의 마찰특성에 미치는 물리적 특성의 영향을 분석한 결과, 마찰각은 모든 암종에서 각각 각력함량 및 단위중량과 양(+)의 상관관계를 가지고, 점토함량, 공극률 및 함수비와 음(-)의 상관관계를 보인다. 대조적으로, 단층핵의 점착력은 각력함량 및 단위중량과 음(-)의 상관관계를 가지고, 점토함량, 공극률 및 함수비와 양(+)의 상관관계를 보인다.
이론적 연구를 통하여 정수압의 영향을 받는 항복기준인 Mohr-Coulomb 항복기준과 Drucker-Prager 항복기준의 강도정수를 ${\pi}$-평면에 대해 일치시킴으로써 강도정수간의 상관관계를 분석해 보았다. Drucker-Prager 강도정수 ${\alpha}$와 k를 Mohr-Coulomb 강도정수인 c와 ${\phi}$를 이용하여 표현하였는데 k는 c, ${\phi}$의 함수로 표현되었고 ${\alpha}$는 ${\phi}$만의 함수로 표현되었다. Drucker-Prager 강도정수 ${\alpha}$값은 흙의 내부마찰각이 커짐에 따라 증가함을 알 수 있었는데 Drucker-Prager 항복기준을 나타내는 원이 Mohr-Coulomb 항복기준에 외접 및 내접하는 경우의 ${\alpha}$값을 나타내는 ${\alpha}_c$와 ${\alpha}_i$값에 대하여 평균값인 ${\alpha}_{av}$의 값은 내부마찰각에 비례하였는데 내부마찰각이 $10^{\circ}$인 경우 약 0.07이었으며 내부마찰각이 $45^{\circ}$인 경우 약 0.29이었다. 또한, ${\alpha}_c/{\alpha}_i$값은 내부마찰각에 비례하였는데 내부마찰각이 $10^{\circ}$인 경우 약 1.12이었으며 내부마찰각이 $45^{\circ}$인 경우 약 1.62이었다. Mohr-Coulomb 강도정수가 Drucker-Prager 강도정수 k에 미치는 영향을 살펴보았는데 본 연구에서 가정한 흙의 점착력 중 최소값이 10kPa인 경우를 제외하고 흙의 내부마찰각의 영향을 거의 받지 않고 전체적으로 흙의 점착력에 영향을 받음을 알 수 있었다. 일정한 점착력에 대하여 내부마찰각이 증가함에 따라 일축압축시 및 일축인장시의 Mohr-Coulomb 항복기준에 의한 축차응력인 $S_{c0}$와 $S_{t0}$ 그리고 두 값의 평균값인 $S_{0(ave)}$값은 감소하였다. 또한 내부마찰각이 증가할수록 Mohr-Coulomb 항복궤적을 나타내는 육각형이 더욱 불규칙해져 $S_{0(ave)}$로부터 $S_{c0}$와 $S_{t0}$ 사이의 편차가 내부마찰각이 증가함에 따라 커짐을 알 수 있었다.
An equivalent friction element is proposed to simulate the friction in cable-strut joints. Equivalent stiffness matrixes and load vectors of the friction element are derived and are unified into patterns for FEM by defining a virtual node specially to store internal forces. Three approaches are described to verify the rationality of the new equivalent friction element: applying the new element in a cable-roller model, and numerical solutions match well with experimental results; applying the element in a continuous sliding cable model, and theoretical values, numerical and experimental results are compared; and the last is applying it in truss string structures, whose results indicate that there would be a great error if the cable of cable supported structures is simulated with discontinuous cable model which is usually adopted in traditional finite element analysis, and that the prestress loss resulted from the friction in cable-strut joints would have adverse effect on the mechanical performance of cable supported structures.
In this paper, a parametric study on the influence of friction between materials on pull force in single clinching is conducted using an axisymmetric elasto-plastic finite element method and law of Coulomb friction. An appropriate finite element analysis model is given, which minimizes the effect of the material model and numerical factors including the number of quadrilateral finite elements and blank radius. It is emphasized that the elasto-plastic material model should be employed because the elastic deformation of the internal region is affected more by the pull force. It has been shown that the pull force increases as friction coefficient increases and that the optimized friction coefficient is around 0.4, which is qualitatively comparable with its theoretical value. When the friction coefficient reaches 0.5 in the example studied, the neck fracture is predicted.
In this study, mechanical and tribological properties were investigated by varying the process temperature (50, 100, 125 and 150℃) to reduce internal stress. The internal stress reduction by thermal dissociation ta-C coating film with increasing temperature is confirmed through the curvature radius of the ta-C coating according to the temperature of the SUS plate. As the coating temperature increased, the mechanical properties (hardness, modulus, toughness) deteriorated, which is in agreement with the Raman analysis results. As the temperature increased, the sp2 phase ratio increased owing to the dissociation of the sp3 phase. The friction and wear properties are related to the process temperature during ta-C coating. Low friction and wear properties are observed in high hardness samples manufactured at 50℃, and wear resistance properties decreased with increasing temperature. The contact area is expected to increase owing to the decrease of hardness(72 GPa to 39 GPa) and fracture toughness with increasing temperature which accelerated wear because of the debris generated. It was confirmed that at process temperature of over than 100℃, the bond structure of the carbon film changed, and the effect of excellent internal stress was reduced. However, the wear resistance simultaneously decreased owing to the reduction in fracture toughness. Therefore, in order to increase industrial utilization, optimum temperature conditions that reduce internal stress and retain mechanical properties.
본 연구에서는 제주도 현무암에 대한 삼축압축시험을 실시하고 암석의 Mohr-Coulomb파괴규준과 Hoek-Brown파괴규준을 적용하여 강도정수를 산정하였다. 그리고 각각의 파괴규준에 의해 산정된 강도정수를 비교검토하여 각각의 파괴규준에 대한 특성을 고찰하였다. 암석의 Mohr-Coulomb파괴규준을 적용한 결과 표선리 현무암의 경우 점착력은 5.35 MPa, 내부마찰각은 $50.25^{\circ}$이고, 조면암질 현무암의 경우 점착력은 16.99 MPa, 내부마찰각은 $60.66^{\circ}$이며, 스코리아의 경우 점착력은 2.33 MPa, 내부마찰각은 $37.05^{\circ}$이다. 암석의 Hoek-Brown의 파괴규준에 대한 회귀분석결과를 토대로 암석의 점착력과 내부마찰각을 선정할 수 있다. 표선리 현무암의 경우 점착력은 4.77 MPa, 내부마찰각은 $52.47^{\circ}$이고, 조면암질 현무암의 경우 점착력은 14.69 MPa, 내부마찰각은 $60.70^{\circ}$이며, 스코리아의 경우 점착력은 2.22 MPa, 내부마찰각은 $47.60^{\circ}$이다. 이상의 결과를 토대로 Mohr-Coulomb의 파괴포락선과 Hoek-Brown의 파괴규준으로부터 추정된 파괴포락선을 비교한 결과 Hoek-Brown의 파괴규준은 Mohr-Coulomb의 파괴규준보다 점착력은 대체로 낮게 평가되는 반면, 내부마찰각은 크게 평가되고 있다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.