• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.2
• /
• pp.213-218
• /
• 2010

A cooling system utilizing liquid helium to chill the cryopanel (800 mm $\times$ 700 mm dimensions) down to 4.2 K was designed, implemented, and tested to verify the role of the cryopanel as a heat sink for the payload of a spacecraft inside the large thermal vacuum chamber (effective dimensions : 8 m ($\Phi$) $\times$ 10 m (L)) of KARI (Korea Aerospace Research Institute). Two LHe (Liquid Helium) Dewars, one for the main supply and the other for refilling, were used to supply liquid helium or cold helium gas into this cryopanel, and flow control for the target temperature of the cryopanel within requirements was done through fine adjustment of the pressure inside the LHe Dewars. The return helium gas from the cryopanel was reused as a thermal barrier to minimize the heat influx on the core liquid helium supply pipe. The test verified a cooling time of around three hours from the ambient temperature to 40 K (combined standard uncertainty of 194 mK), the capacity for maintaining the cryopanel at intermediate temperatures, and a 1 K uniformity over the entire cryopanel surface at around 40 K with 20 W cooling power.

• Journal of Powder Materials
• /
• v.20 no.2
• /
• pp.142-147
• /
• 2013

$YBa_2Cu_3O_{7-y}$ (Y123) powders for the fabrication of bulk superconductors were synthesized by the powder reaction method using $Y_2O_3$ (99.9% purity), $BaCO_3$ (99.75%) and CuO (99.9%) powders. The raw powders were weighed to the cation ratio of Y:Ba:Cu=1:2:3, mixed and calcined at $880^{\circ}C-930^{\circ}C$ in air with intermediate repeated crushing steps. It was found that the formation of Y123 powder was more sensitive to reaction temperature than reaction time. The calcined Y123 powder and a mixture of (Y123 + 0.25 mole $Y_2O_3$ + 1 wt.% $CeO_2$, $Y_{1.5}Ba_2Cu_3O_x$ (Y1.5)) were used as raw powders for the fabrication of poly-grain or single grain superconductors. The superconducting transition temperature ($T_{c,onset}$) of the sintered Y123 sample was 91 K and the transition width was as large as 11 K, whereas the $T_{c,onset}$ of the melt-grown Y1.5 sample was 90.5 K and the transition width was 3.5 K. The critical current density ($J_c$) at 77 K and 0 T of the sintered Y123 was 700 $A/cm^2$, whereas the $J_c$ of the top-seeded melt growth (TSMG) processed Y1.5 sample was $3.2{\times}10^4\;A/cm^2$. The magnetic flux density (H) at 77 K of the TSMG-processed Y123 and Y1.5 sample showed the 0.53 kG and 2.45 kG, respectively, which are 15% and 71% of the applied magnetic field of 3.5 kG. The high H value of the TSMG-processed Y1.5 sample is attributed to the formation of the larger superconducting grain with fine Y211 dispersion.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.5
• /
• pp.200-204
• /
• 2008

Mechano Chemical Process (MCP) skips the calcinations steps at an intermediate temperature that is always required in the conventional solid-state reaction because forming phase from raw powder is activated by mechanical energy. In this study, we prepared (Pb, La)$TiO_3$ nanopowder with perovskite structure by only high energy MCP. Especially, the PLT nanopowder was synthesized without any thermal treatment using oxides, not salts as raw powder. This process is also very simple due to dry milling method, unnecessary to dry of powder. The oxide powder was milled up to 12 hr at intervals of an hour using MCP and the pure PLT phase of perovskite structure was formed after milling time of 3 hr. And the average particle size was 20 nm with narrow distribution after milling time of 3 hr from raw powder of several $\mu m$ with inhomogeneous distribution.

• Fire Science and Engineering
• /
• v.31 no.3
• /
• pp.25-30
• /
• 2017

Because of the vertical combustion characteristics of combustible substances, accurate substance safety information for their safe use, handling and transportation is essential. The flash point, fire point, explosion limits and autoignition temperature (AIT) are important safety parameters which need special attention in chemical plants and laboratories that handle dangerous materials. In this study, tert-butylbenzene which is widely used as an intermediate material in the chemical industry was selected. For the reliability of the flammable properties of tert-butylbenzene, this study was investigated the explosion limits of tert-butylbenzene in the reference data. The flash points, fire points and AITs by the ignition delay time for tert-butylbenzene were experimented. The lower flash points of tert-butylbenzene by using the Setaflash and Pensky-Martens closed-cup testers measured $39^{\circ}C$ and $44^{\circ}C$, respectively. The flash points of tert-butylbenzene by using the Tag and Cleveland open cup testers are measured $51^{\circ}C$ and $54^{\circ}C$. And the fire points of tert-butylbenzene by the Tag and Cleveland open cup testers were $54^{\circ}C$ and $58^{\circ}C$ respectively. The AIT of tert-butylbenzene measured by the ASTM 659E tester was measured as $450^{\circ}C$. The lower explosion limit of $39^{\circ}C$ which measured by the Setaflash flash point tester was calculated to be 0.68 vol%.

• Korean Chemical Engineering Research
• /
• v.56 no.4
• /
• pp.474-478
• /
• 2018

For process safety, fire and explosion characteristics of combustible materials handled at industrial fields must be available. The combustion properties for the prevention of the accidents in the work place are flash point, fire point, explosion limit, and autoignition temperature (AIT) etc.. However, the combustion properties suggested in the Material Safety Data Sheet (MSDS) are presented differently according to the literatures. The accurate combustion properties are necessary to safely treatment, transportation and handling of flammable substances. In the chemical industries, n-ethylaniline which is widely used as a raw material of intermediate products and rubber chemicals was selected. For safe handling of n-ethyl aniline, the flash point, the fire point and the AIT were measured. The lower explosion limit (LEL)of n-ethylaniline was calculated using the lower flash point obtained in the experiment. The flash points of n- ethylaniline by using the Setaflash and Pensky-Martens closed-cup testers measured $77^{\circ}C$ and $82^{\circ}C$, respectively. The flash points of n-ethylaniline using the Tag and Cleveland open cup testers are measured $85^{\circ}C$ and $92^{\circ}C$, respectively. The AIT of the measured n-ethyl aniline by the ASTM E659 apparatus was measured at $396^{\circ}C$. The LEL of n-ethylaniline measured by Setaflash closed-cup tester at $77^{\circ}C$ was calculated to be 1.02 vol%. In this study, it was possible to predict the LEL by using the lower flash point of n-ethylaniline measured by closed-cup tester. The relationship between the ignition temperature and the ignition delay time of the n-ethylaniline proposed in this study makes it possible to predict the ignition delay time at different ignition temperatures.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.27 no.11
• /
• pp.581-586
• /
• 2015

In this study, an analysis was performed on the performance of the solar water heating system with geo-thermal heat pump for a detached house. This system has a flat plate solar collector ($8\;m^2$) and a 3 RT heat pump. The heat pump acts as an auxiliary heater of the solar water heating system. These systems were installed at four individual houses with the same area of $100\;m^2$. The monitoring results for one year are as follows. (1) The average daily operating time of the solar system appeared to be 313 minutes in spring (intermediate season), and 135 minutes and 76 minutes in winter and summer respectively. The reason for the short operating time in summer is the high storage temperature due to low water heating load. The high storage temperature is caused by a decrease in collecting efficiency as well as by overheating. (2) The geothermal heat pump as an auxiliary heater mainly operates on days of poor insolation during the winter season. (3) Despite controlling for total house area, hot water consumption varies greatly according to the number of people in the family, hot water usage habits, etc. (4) The yearly solar fraction was 69.8 to 91.5 percent, which exceeds the maximum value of 80% as recommended by ASHRAE. So the solar collector area of $8\;m^2$ appeared to be somewhat greater for the house with an area of $100\;m^2$. (5) The observed annual efficiency of solar systems was relatively low at 13.5 to 23.6%, which was analyzed to be due to the decrease in thermal efficiency and the overheating caused by a high solar fraction.

• Journal of Soil and Groundwater Environment
• /
• v.10 no.6
• /
• pp.45-55
• /
• 2005

The geothermal research has been carried out on the Heunghae, Pohang geothermal area know as having geo-heat-flow area in the Korean peninsula. This study results so far indicate that geothermal water in the area is in peripheral waters of hydrothermal area and is not in equilibrium with the reservoir rock. The average oxygen and hydrogen stable isotope values are as follows: deep groundwater $(average:\;{\delta}^{18}O=-10.1\%_{\circ},\;{\delta}D=-65.8\%_{\circ})$, intermediate groundwater (average: $(average:\;{\delta}^{18}O=-8.9\%_{\circ},\;{\delta}D=-59.6\%_{\circ})$, shallow groundwater $(average:\;{\delta}^{18}O=-8.0\%_{\circ},\;{\delta}D=-53.6\%_{\circ})$, surface water $(average:\;{\delta}^{18}O=-7.9\%_{\circ},\;{\delta}D=-53.3\%_{\circ})$ respectively. Deep groundwaters was originated from a local meteoric water recharged from distant, topographically high mountain region and not affected by the sea water. High temperature zone inferred from water geothermometers is around D-1, D-5, D-6, 1-04 well zones. The estimated enthalpy from Silica-enthalpy mixing model is near 410 kJ/kg, which corresponds to the temperature of $98^{\circ}C$, and in consistent with the result of Na-K and K-Mg geothermometer.

• 한국해양학회지
• /
• v.26 no.1
• /
• pp.83-100
• /
• 1991

A layer of salinity-minimum which characterizes the East Sea intermediate Water (ESIW) is found at an approximate depth of 200 m in three CTD section taken in the Ulleung Basin on May 17-21, 1988. Properties at this layer vary in ranges of $1.1^{\circ}C except at stations near the east coast of Korea where temperature is as high as $4.39^{\circ}C$ and salinity is as low as $33.992{\textperthousand}$. To be distinguished from the ESIW the East Sea Proper Water (ESPW) may be characterized by temperature less than $1^{\circ}C$, Salinity at the saliently-minimum layer and 500db increases southward in general, implying that the cold waters, both ESIW and ESPW, formed in the northern basin of the East Sea are spreading southward below the permanent thermocline in the basin. Hydrography in the Ulleung Basin is very similar to that in the Alboran Sea, suggesting a possibility of an anticyclonic circulation in the Ulleung Basin which is controlled strongly by the shoaling bottom.

• Korean Journal of Poultry Science
• /
• v.6 no.1
• /
• pp.24-30
• /
• 1979

1. The effects of heat stress (38$^{\circ}C$), cold stress (4$^{\circ}C$) and extreme cold stress (-20$^{\circ}C$) before slaughter on the tenderness and postmortem glycolysis if the excised chicken breast muscle were studied Heat stress significantly (p 0.05) increased the toughness of breast muscle. Though statistically not significant, cold stress also adversely affected the tenderness. The heat-stressed birds showed higher zero hr glycogen higher zero hr pH and significantly (p 0.05) love. ultimate pH then the controls. The cold-stressed birds showed intermediate values in these parameters. Highly significant correlations. were observed between shear value and each of these three parameters. Glycolysis rate ana final moisture content were minor factors which affected the muscle tenderness to a limited extent. The slightly elevated lactate-dehydrogenase and creatine phosphokinase activities in serum and breast muscle of stressed birds failed to account for any variations in tenderness. 2. Chicken breast and thigh muscles were subjected to different environmental temperatures to determine if the phenomenon of cold shortening exists in chicken muscle. For both breast and thigh muscles, minimum shortening was observed in the 4-10$^{\circ}C$t range. Muscles held at 0$^{\circ}C$ showed a slightly higher extent of shortening than at 4$^{\circ}C$; where as muscles held at above 20$^{\circ}C$ showed a severe shortening effect. It was concluded that no apparent cold shortening was detected in chicken muscle except at 0$^{\circ}C$ and even at 0$^{\circ}C$ and even at 0$^{\circ}C$ the extent of shortening was of a small magnitude compared to bovine muscles. Since high temperature induces a much greater shortening, muscle temperature must be lowered to below 20$^{\circ}C$ as early as possible to prevent excessive muse]e shortening.

• The Journal of the Petrological Society of Korea
• /
• v.8 no.2
• /
• pp.71-80
• /
• 1999

We report zircon morphology of granitoids in the Mt. Keumjeong district, Pusan. There are a series of granitoids in the study area of the late Cretaceous: granodiorite, hornblende granite, adamellite, tonalite, biotite granite, and micrographic granite. Generally, the shapes of zircon crystals are short prismatic to middle prismatic and are dominant in {loo) prism and {101) pyramid in total average morphological data of the granitoids. The crystal forms of zircon in the granitoids can be distinguished by the PPEF diagram and the prism index (PI). The prism index values of zircon crystal forms in granodoirite and hornblende granite are higher than those of tonalite and micrographic granite. The finishing temperature range ($820~800^{\circ}C$) for crystallization of zircon crystals in granodoirite and hornblende granite is higher than the temperature ($790~770^{\circ}C$) at which the zircon crystals are created in tonalite and micrographic granite. The last differentiates (biotite granite and micrographic granite) have mainly intermediate zircon ({110)={100)) crystals, respectively. As differentiation proceeds, the zircons of granitoids become from short prismatic to middle prismatic in the each granitoid types.