• Journal of KSNVE
• /
• v.8 no.2
• /
• pp.331-335
• /
• 1998

A design modification was made on the 9-th stage wheel dovetail of a high-intermediate pressure (HIP) turbine rotor for a fossil power plant that necessitates the use of new long-shank buckets for the row. A bucket vibration test is necessary to verify that the new 9-th stage buckets have adequate frequency margin from a nozzle passing frequency when running at speed. A finite element analysis (FEA) has been performed using a commercial S/W to approximately estimate bucket natural frequencies, and thus to help the vibration test. A row of the new buckets has assembled on the HIP rotor for the vibration tests using dynamic balancing facilities. The tests have been done during deceleration run with air excitation. The test results are compared with the calculation using our empirical formula, and show that the modified design meets the frequency-margin requirements.

• Journal of Positioning, Navigation, and Timing
• /
• v.6 no.1
• /
• pp.1-8
• /
• 2017

In this study, to design a multi-GNSS receiver using single RF front-end, the receiving performances for various frequency plans were evaluated. For the fair evaluation and comparison of different frequency plans, the same signal needs to be received at the same time. For this purpose, two synchronized RF front-ends were configured using USRP X310, and PC-based software was implemented so that the quality of the digital IF signal received at each front-end could be evaluated. The software consisted of USRP control, signal reception, signal acquisition, signal tracking, and C/N0 estimation function. Using the implemented software and USRP-based hardware, the signal receiving performances for various frequency plans, such as the signal attenuation status, overlapping of different systems, and the use of imaginary or real signal, were evaluated based on the C/N0 value. The results of the receiving performance measurement for the various frequency plans suggested in this study would be useful reference data for the design of a multi-GNSS receiver in the future.

• English Language & Literature Teaching
• /
• v.12 no.2
• /
• pp.61-85
• /
• 2006

The purpose of the present study is to compare Korean EFL learners' speech corpus (i.e. oral productions) with their composition corpus (i.e. written productions). Four college students participated in the study. The composition corpus was collected through a writing assignment, and the speech corpus was gathered by audio-taping their oral presentations. The results of the data analysis indicate that (i) As for error frequency, young adult low-intermediate Korean EFL learners showed high frequency in determiners (mostly, indefinite articles), vocabulary (mostly, semantic errors), and prepositions. The frequency order did not show much difference between the speech corpus and the composition corpus; and (ii) When comparing the oral productions with the written productions, there were not many differences between them in terms of the contents, a style (i.e., colloquial vs. literary), vocabulary selection, and error types and frequency. Therefore, it is assumed that the proficiency in oral presentation of EFL learners at this learning stage heavily depends on how much/how well they are able to write. In other words, EFL learners' writing and speaking skills are closely co-related. It implies that the teacher does not need to separate teaching how to speak from teaching how to write. The teacher may use the same methods or strategies to help the learners improve their English speaking and writing skills. Furthermore, it will be more effective to teach writing before speaking since they have more opportunities to write than speak in the EFL contexts.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.1
• /
• pp.8-15
• /
• 2016

As a generalized form of the conventional Fourier transform, fractional Fourier transform (FrFT) can analyze a signal at intermediate domain between time and frequency domains with a transform order ${\alpha}$. Especially, FrFT has a number of advantages in the analysis of LFM (Linear Frequency Modulation) signals due to its robustness to noise. In this paper, we have proposed a new method to detect and estimate the distance of the target from the FrFT spectrum of the received echo signal. Experimental results have validated the proposed method, and shown that reliable target distance could be estimated in noise and reverberation environments.

• Journal of IKEEE
• /
• v.16 no.2
• /
• pp.121-126
• /
• 2012

In this paper, a push-push VCDRO (Voltage Controlled Dielectric Resonator Oscillator) with a modified frequency tuning structure is investigated. The push-push VCDRO designed at 16GHz is manufactured using a LTCC (Low Temperature Co-fired Ceramic) technology to reduce the circuit size. The frequency tuning structure is embedded in intermediate layer of A6 substrate by an advantage of LTCC process. Experimental results show that the fundamental frequency suppression is above 30dBc, the frequency tuning range is 0.43MHz over control voltage of 0 to 12V, and phase noise of push-push VCDRO presents a good performance of -103dBc/Hz at 100KHz offset frequency from carrier.

• ETRI Journal
• /
• v.35 no.3
• /
• pp.386-396
• /
• 2013

A 10-Gbit/s wireless communication system operating at a carrier frequency of 300 GHz is presented. The modulation scheme is amplitude shift keying in incoherent mode with a high intermediate frequency (IF) of 30 GHz and a bandwidth of 20 GHz for transmitting a 10-Gbit/s baseband (BB) data signal. A single sideband transmission is implemented using a waveguide-tapered 270-GHz high-pass filter with a lower sideband rejection of around 60 dB. This paper presents an all-electronic design of a terahertz communication system, including the major modules of the BB and IF band as well as the RF modules. The wireless link shows that, aided by a clock and data recovery circuit, it can receive $2^7$-1 pseudorandom binary sequence data without error at up to 10 Gbit/s for over 1.2 m using collimating lenses, where the transmitted power is 10 ${\mu}W$.

• Journal of KSNVE
• /
• v.7 no.1
• /
• pp.61-69
• /
• 1997

Despite of the development in the finite element method, it is difficult to get the finite element model describing the dynamic characteristics of the complex structure exactly. Therefore a number of different methods have been developed in order to update the finite element model of a structure using vibration test data. This paper outlines the basic formulation for the frequency response function based updating method. One important advantage of this method is that the intermediate step of performing an eigensolution extraction is unnecessary. Using simulated experimental data, studies are conducted in the case of 10 DOF discrete system. The solution of noisy and incomplete experimental data is discussed. True measured frequency response function data are used for updating the finite element model of a beam and a plate. Its applicability to the joint identification is also considered.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.11 no.4
• /
• pp.43-51
• /
• 2001

An experimental modal analysis is the process to identify structure's dynamic characteristics such as resonant frequencies, damping values and mode shapes. An experimental model was made of stainless steel in the shape of a circular cylindrical shell and installed on the test bed with jigs. For investigating vibrational characteristics of the continuous circular cylindrical shell with intermediate supports, modal testing is performed by using impact hammer, accelerometer and 8-channel FFT analyzer. The frequency response function(FRF) measurements are also made on the experimental model within the frequency range from 0 to 4kHz. Modal parameters are identified from resonant peaks in the FRF's and animated deformation patterns associated with each of the resonances are shown on a computer screen. The experimental results are compared with analytical and FEA results.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.8 no.4 s.23
• /
• pp.102-109
• /
• 2005

In this paper, we propose a new listen-in technique to overcome the problems and the shortcomings which could possibly meet in the previous listen-in methods to deal with the blind signal manually according to operator's decision. In the proposed listen-in method, receiving the signals, classifying the modulation types, and demodulating the signals can be done automatically without operator's intervention. We realize the listen-in technology by developing the high speed frequency tuner, the automatic modulation recognizer, and the signal demodulator. In conclusion, we confirm and show that the developed equipment has a good performance in classifying the modulation type through the computer simulation and the field test.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.4C no.6
• /
• pp.306-309
• /
• 2004

This paper presents a new active antenna consisting of a microstrip patch for the passive radiator, a mixer for frequency conversion, a voltage controlled oscillator (VCO) and a phase detector for phase control. The microwave signal frequency has been converted into intermediate frequency (IF) on the antenna elements by the mixer. The active antenna consists of two ports, the IF port has a transmitted IF signal via power combined to the baseband and the dc control port is under the control of the phase-detector. The input voltage of the VCO is controlled by the phase detector. The scan range of the array is determined by the phase detector and the VCO and is obtained between 30$^{\circ}$ and - 30$^{\circ}$