• 한국재료학회지
• /
• 제30권1호
• /
• pp.8-13
• /
• 2020

Effect of heat treatment on microstructure and mechanical properties of an Fe-6.5Mn-0.08C medium-manganese steel is investigated in this study. Three kinds of medium-manganese steel specimens are fabricated by varying heat treatments of intermediate quenching (IQ), step quenching (SQ), and intercritical annealing (IA). Hardness and tensile tests are performed to examine the correlation of microstructure and mechanical properties for the Fe-6.5Mn-0.08C medium-manganese steel specimens. The IQ and SQ specimens have microstructures of martensite matrix with ferrite, whereas IA specimen exhibits microstructure of acicular ferrite matrix with martensite. The tensile test results show that the SQ specimen with martensite matrix has the highest yield strength and the lowest elongation. On the other hand, the SQ specimen has the highest hardness due to the relatively lower reduction of carbon content in martensite during intercritical annealing. According to the fractography of tensile tested specimens, the SQ specimen exhibits a dimple and quasi-cleavage fracture appearance while the IQ and IA specimens have fully ductile fracture appearance with fine-sized dimples caused by microvoid coalescence at ferrite and martensite interface.

• 한국광물학회지
• /
• 제16권1호
• /
• pp.91-106
• /
• 2003

Na-장석(Amelia albite)의 등온가열 실험에 대한 XRD 분석 결과는 $1073^{\circ}C$의 가열 시료에서 격자상수의 급격한 변화를 보여주는데, 이는 Al과 Si의 비배열(disordering)과 가열된 시료의 급랭에 의한 격자 변형 때문이라고 본다. $1073^{\circ}C$에서는 약 7일 간의 가열에 의해 저온 알바이트에서 고온 알바이트로 상전이한 반면, $924^{\circ}C$에서는 Al-Si의 비배열 속도가 느려서 140일 동안 가열된 시료도 초기 단계의 중간단계 알바이트 상태로 남아 있었다. TEM 분석 결과는 가열된 시료에서 100∼200$\AA$ 크기의 트위드(tweed) 구조가 형성됨이 특징적인데, 이 구조의 발달 및 변화는 고온($1073^{\circ}C$)과 저온 ($923^{\circ}C$)의 가열 시료가 다름이 드러났다. 즉, 전자는 국부적으로 알바이트 쌍정과 유사한 미세구조로 전이한데 반해, 후자는 보다 넓은 지역에 걸쳐 알바이트 쌍정면이 우세한 도메인 구조로 전이하였다. 가열에 의한 Al과 Si의 비배열과 급랭에 의한 응력 때문에 격자의 불안정(lattice instability)이 증가하게 되는데 이를 완화시키기 위하여 태아 단계의 쌍정 구조(알바이트 쌍정과 pericline 쌍정)를 형성되는 것이 트위드 구조의 원인이라고 본다.

• 열처리공학회지
• /
• 제18권5호
• /
• pp.288-296
• /
• 2005

The corrosion behaviors of Zr-based alloys were very sensitive to their microstructures which were determined by manufacturing process. The specimens of Zr-based alloy named as HANA-4 for nuclear fuel cladding were investigated in order to get the optimized manufacturing process such as the intermediate annealing temperature and cold working steps after the ${\beta}$ quenching. From the microstructural analysis, cold worked microstructure of the samples was changed to the recrystallized microstructure by performed process. The corrosion behaviors of HANA-4 alloy were affected by the different manufacturing process. The ${\beta}$-Zr phase was formed in the matrix and the Nb concentration in the ${\beta}$-Zr phase was increased as progressing the manufacturing process. So, it was found that the corrosion rate of HANA-4 alloy was affected by the Nb concentration in the matrix.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.160-160
• /
• 2011

In the present work, $TiO_2$ fiilms supported by porous silica gel with high surface area synthesized by atomic layer deposition(ALD). Porous structure of silica substrate could be maintained even after deposit large amount of $TiO_2$ (500 cycles of ALD process), suggesting the differential growth mode of $TiO_2$ on top surface and inside the pore. All the $TiO_2$-covered silica samples showed improved MB adsorption abilities, comparing to bare one. In addition, when silica surface was covered with $TiO_2$ films, MB adsorption capacity was almost fully recovered by re-annealing process (500$^{\circ}C$, for 1 hr, in ambient pressure), whereas MB adsorption capacity of bare silica was decreased after re-heaing process. FT-IR study demonstrated that $TiO_2$ film could prevent deposition of surface-bound intermediate species during thermal decomposition of adsorbed MB molecules. Photocatalytic activity of $TiO_2$/silica sample was also investigated.

• Nuclear Engineering and Technology
• /
• 제30권3호
• /
• pp.262-272
• /
• 1998

The experiences and causes of pressure tube cracking accidents in the CANDU reactors and the development of the fuel channel at AECL(Atomic Energy Canada Limited) have been described. Most of the accidents were caused by Delayed Hydride Cracking(DHC). In the cases of the Pickering units 3&4 and the Bruce unit 2, excessive residual stresses induced by an improper rolled joint process played a role in DHC. In the Pickering unit 2, cracks formed by contact between the pressure and calandria tubes due to the movement of the garter spring were the direct cause of the failure. To extend the life of a fuel channel, several R&D programs examining each component of the fuel channel have been carried out in Canada. For a pressure tube, the main concern is focused on changing the fabrication processes, e.g., increasing cold working rate, conducting intermediate annealing and adding a third element like Fe, V, and Cr to the tube material. In addition to them, chromium plating on the end fitting and increasing wall thickness at both ends of the calandria tube are considered. There has also been much interest in the improvement of fuel channel performance in our country and several development programs are currently under way.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.374-375
• /
• 2006

This paper describes anodic bonding characteristics of MCA to Si-wafer using evaporated Pyrex #7740 glass thin-films for MEMS applications. Pyrex #7740 glass thin-films with the same properties were deposited on MCA under optimum RF sputter conditions (Ar 100 %, input power $1\;W/cm^2$). After annealing at $450^{\circ}C$ for 1 hr, the anodic bonding of MCA to Si-wafer was successfully performed at 600 V, $400^{\circ}C$ in $110^{-6}$ Torr vacuum condition. Then, the MCA/Si bonded interface and fabricated Si diaphragm deflection characteristics were analyzed through the actuation and simulation test. It is possible to control with accurate deflection of Si diaphragm according to its geometries and its maximum non-linearity being 0.05-0.08 %FS. Moreover, any damages or separation of MCNSi bonded interfaces did not occur during actuation test. Therefore, it is expected that anodic bonding technology of MCNSi-wafers could be usefully applied for the fabrication process of high-performance piezoelectric MEMS devices.

• 한국초전도ㆍ저온공학회논문지
• /
• 제23권1호
• /
• pp.12-16
• /
• 2021

The magnetic properties of heat treated O-series high temperature superconducting (HTS) GdBCO coated conductor (CC) tapes which were formed of Ag/GdBCO/Buffer-layers/Stainless Steel (SS), were investigated by employing a Quantum Design PPMS-14. Using a modified Bean model, the critical current density J_c values have been estimated from the 𝚫m_irr(H) data, which are obtained by measuring the magnetic moment m(H) loops. For a range of intermediate fields, which are interacting or collective flux pinning area, the magnetic flux behaviors were investigated from the relationship J_c ∝ H^-β. In addition, the changes of irreversibility magnetic field H_irr line of heat-treated O-series HTS GdBCO CC tapes were analyzed, according as the annealing temperature under oxygen flowing increases. Both weak and strong break-downs were found by examining the changes of irreversibility magnetic field H_irr lines.

• 한국식품과학회지
• /
• 제53권6호
• /
• pp.731-738
• /
• 2021

쌀전분 생산 원료로서 쇄미의 활용 가능성을 조사하기 위해 예산, 김포, 평택 지역의 미곡종합처리장들에서 얻은 대쇄미를 알칼리침지법과 효소소화법을 이용하여 쌀전분을 제조하고, 이들의 물리화학적 특성을 조사하였다. 쇄미의 조단백질 함량은 김포>평택>예산의 순서로 증가하였지만, 국내 주요 11품종 쌀의 조단백질 함량 범위를 초과하거나 미달하였다. 쇄미가루의 총 전분함량은 지역별 차이는 크지 않았으며, 정미의 총 전분 함량 범위내에 있어 쌀전분 생산 원료로 사용할 수 있다. 지역별 쇄미가루로부터 알칼리침지법과 효소소화법에 따라 제조된 쇄미전분의 조단백질 함량은 1% 내외로 상업적 생전분으로 활용이 가능 수준이었다. 아밀로스 함량은 지역별로 소폭 차이가 존재하였지만, 제조방법에 따른 유의적 차이는 관찰되지 않았다. 쇄미전분들의 형태학적 특성은 일반적인 쌀전분과 다르지 않았으며, 제조방법에 따른 구조적 변형은 관찰되지 않았다. X선 회절패턴은 모든 쇄미전분들에서 전형적인 A형 결정 배열을 나타내었으며, 제조방법에 따른 결정구조의 변형은 관찰되지 않았지만 상대결정도에 있어 차이가 존재하였다. 호화특성에 있어 알칼리침지법보다 효소소화법에 의한 쇄미전분들이 높은 호화개시온도 및 호화최고 온도와 좁은 호화온도범위를 나타내었다. 관찰된 상대결정도와 호화온도의 차이는 annealing이 효소소화법에 따른 쇄미전분에서 발생하였다는 것을 가리킨다. 팽윤력과 용해도는 알칼리침지법보다 효소소화법에 따른 쇄미전분에서 일반적으로 낮은 수준을 나타내었다. 페이스팅 점도 특성에 있어 알칼리침지법보다 효소소화법에 의한 쇄미전분은 페이스팅 점도의 발달이 지연되었으며, 높은 최고점도와 최저점도를, 낮은 붕괴점도, 최종점도와 치반점도를 나타내었다. 이와 같은 팽윤력, 용해도 및 페이스팅 점도의 차이는 효소소화법에 의한 쇄미전분들의 annealing 때문이다. 전체적인 결과를 종합하면, 쇄미는 쌀전분의 원료로 사용할 수 있으며, 효소소화법은 알칼리침지법에 따른 쌀전분의 팽윤력, 용해도, 호화특성 및 페이스팅 점도 특성과는 다른 쌀전분을 제조할 수 있을 것이다. 게다가 쌀전분의 높은 가격이 비싼 원료쌀과 높은 생산비용 때문임을 고려할 때, 쌀전분 원료로 쇄미의 사용에 따른 쌀전분 생산원가의 절감은 판매가격을 낮춰 쌀전분의 식품 및 비식품 산업적 활용도를 높일 수 있을 것이다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.851-856
• /
• 2003

We have investigated the material and electrical properties of $Bi_{4-x}La_xTi_3O_{12}$ (BLT) ferroelectric thin film for ferroelectric nonvolatile memory applications of capacitor type and single transistor type. The 120nm thick BLT films were deposited on $Pt/Ti/SiO_2/Si$ and $SiO_2/Nitride/SiO_2$ (ONO) substrates by the sol-gel spin coating method and were annealed at $700^{\circ}C$. It was observed that the crystallographic orientation of BLT thin films were strongly affected by the excess Bi content and the intermediate rapid thermal annealing (RTA) treatment conditions regardeless of two type substrates. However, the surface microstructure and roughness of BLT films showed dependence of two different type substrates with orientation of (111) plane and amorphous phase. As increase excess Bi content, the crystallographic orientation of the BLT films varied drastically in BLT films and exhibited well-crystallized phase. Also, the conversion of crystallographic orientation at intermediate RTA temperature of above $450^{\circ}C$ started to be observed in BLT thin films with above excess 6.5% Bi content and the rms roughness of films is decreased. We found that the electrical properties of BLT films such as the P-V hysteresis loop and leakage current were effectively modulated by the crystallographic orientations change of thin films.

• 한국결정성장학회지
• /
• 제8권4호
• /
• pp.655-659
• /
• 1998

과냉각된 melt-spun $Nd_{14.73}Fe_{78.67}B_{6.60}$리본의 급속응고속도 및 열처리에 따른 보자력의 변화를 조사하였으며, 이 결과를 분석하기 위하여 비정질로 부터의 결정화 거동을 연구하였다. 리본 제조시 급속응고속도가 증가함에 따라 결정화 후의 고유 보자력은 감소하였다. $Nd_{14.73}Fe_{78.67}B_{6.60}$ 비정질은 안정한 $Nd_2Fe_{14}B$ 상으로 결정화하는 과정에서 $\alpha$-Fe와 $Fe_3B$ 상이 생성된다. $Fe_3B$ 상은 $Nd_2Fe_{14}B$ 상이 결정화됨과 동시에 사라지나 $\alpha$-Fe 상은 완전히 결정화된 이후에도 기지상인 $Nd_2Fe_{14}B$ 상과 함께 잔류한다. 열처리된 리본내에 잔류하는 연자성상인 $\alpha$-Fe에 의해 고유 보자력의 특성이 저하하였다.