• 한국주조공학회지
• /
• 제17권2호
• /
• pp.188-194
• /
• 1997

The effects of solidification condition and vibration on structure refinement were investigated for unidirectionally solidified $Al-CuAl_2$ eutectic composites. Eutectic composites were unidirectionally solidified under vibration with different growth rates (R) and thermal gradient(G). The lamellar structure was varied according to growth condition (G/R ratio). For the structure refinement the effect of G/R was found out to be greater than that of vibration. The interlamellar spacing(${\lambda}$) in this materials was varied with the growth rates(R) with "${\lambda}^2R$=Constant" relationship.

• 대한화학회지
• /
• 제21권4호
• /
• pp.246-255
• /
• 1977

여러 종류의 層間 陽이온을 가지고 있는 層狀 硅酸鹽上에서 일어난 methylmethacrylate의 吸着에 關하여 赤外線 分光法과 X-ray로 硏究하였다. 吸着된 methylmethacrylate의 여러 개의 特性 carbonyl band가 陽이온의 種과 脫水溫度에 따라서 다르게 1723∼1547$cm^{-1}$의 範圍에서 나타났다. 190$cm^{-1}$程度로 shift한 carbonyl 伸縮 band는 polyvalent 陽이온에만 나타났으며 $>C=O{\cdot}{\cdot}{\cdot}M^{n+}$型 着物形成 基因하는 것이었다. 1703∼1640$cm^{-1}$에서 나타난 band는 carbonyl 酸素와 陽이온 水 또는 陽이온 水酸基와의 水素結合에 依한 것이었고 shift한 정도는 層間 陽이온의 polarizing power와 좋은 相互 關係를 이루었다. 그러나 1723$cm^{-1}$에서 나타난 band는 陽이온의 鍾과는 相互 關係가 없었으며 carbonyl ,酸素와 表面 水酸基와의 相互 作用으로 因한 것이었다. Interlamellar spacing을 계산해 본 結果 methylmethacrylate의 分子平面은 硅酸鹽의 層과 平行하게 놓여 있는 것 같다.

• 마이크로전자및패키징학회지
• /
• 제15권4호
• /
• pp.9-15
• /
• 2008

Au와 Sn을 순차적으로 도금한 Au/Sn 범프를 플립칩 본딩하여 Au-Sn 솔더 접속부를 형성 후, 미세구조와 접속저항을 분석하였다. $285^{\circ}C$에서 30초간 플립칩 본딩한 Au-Sn 솔더 접속부는 $Au_5Sn$+AuSn lamellar 구조로 이루어져 있으며, 이 시편을 $310^{\circ}C$에서 3분간 유지하여 2차 리플로우시 $Au_5Sn$+AuSn interlamellar spacing이 증가하였다. $285^{\circ}C$에서 30초간 플립칩 본딩한 Au-Sn 접속부는 15.6 $m{\Omega}$/bump의 평균 접속저항을 나타내었으며, 이 시편을 다시 $310^{\circ}C$에서 3분간 유지하여 2차 리플로우 한 Au-Sn 접속부는 15.0 $m{\Omega}$/bump의 평균 접속저항을 나타내었다.

• 한국재료학회지
• /
• 제25권11호
• /
• pp.583-589
• /
• 2015

This paper presents a study on the room- and low-temperature impact toughness of hypoeutectoid steels with ferrite-pearlite structures. Six kinds of hypoeutectoid steel specimens were fabricated by varying the carbon content and austenitizing temperature to investigate the effect of microstructural factors such as pearlite volume fraction, interlamellar spacing, and cementite thickness on the impact toughness. The pearlite volume fraction usually increased with increasing carbon content and austenitizing temperature, while the pearlite interlamellar spacing and cementite thickness mostly decreased with increasing carbon content and austenitizing temperature. The 30C steel with medium pearlite volume fraction and higher manganese content, on the other hand, even though it had a higher volume fraction of pearlite than did the 20C steel, showed a better low-temperature toughness due to its having the lowest ductile-brittle transition temperature. This is because various microstructural factors in addition to the pearlite volume fraction largely affect the ductile-brittle transition temperature and low-temperature toughness of hypoeutectoid steels with ferrite-pearlite structure. In order to improve the room- and low-temperature impact toughness of hypoeutectoid steels with different ferrite-pearlite structures, therefore, more systematic studies are required to understand the effects of various microstructural factors on impact toughness, with a viewpoint of ductile-brittle transition temperature.

• 한국재료학회지
• /
• 제27권4호
• /
• pp.184-191
• /
• 2017

This present study deals with the effect of micro-alloying elements and transformation temperature on the correlation of microstructure and tensile properties of low-carbon steels with ferrite-pearlite microstructure. Six kinds of low-carbon steel specimens were fabricated by adding micro-alloying elements of Nb, Ti and V, and by varying isothermal transformation temperature. Ferrite grain size of the specimens containing mirco-alloying elements was smaller than that of the Base specimens because of pinning effect by the precipitates of carbonitrides at austenite grain boundaries. The pearlite interlamellar spacing and cementite thickness decreased with decreasing transformation temperature, while the pearlite volume fraction was hardly affected by micro-alloying elements and transformation temperature. The room-temperature tensile test results showed that the yield strength increased mostly with decreasing ferrite grain size and elongation was slightly improved as the ferrite grain size and pearlite interlamellar spacing decreased. All the specimens exhibited a discontinuous yielding behavior and the yield point elongation of the Nb4 and TiNbV specimens containing micro-alloying elements was larger than that of the Base specimens, presumably due to repetitive pinning and release of dislocation by the fine precipitates of carbonitrides.

• 한국재료학회지
• /
• 제21권6호
• /
• pp.334-340
• /
• 2011

Saw wires have been widely used in industries to slice silicon (Si) ingots into thin wafers for semiconductor fabrication. This study investigated the microstructural and mechanical properties, such as abrasive wear and tensile properties, of a saw wire sample of 0.84 wt.% carbon steel with a 120 ${\mu}M$ diameter. The samples were subjected to heat treatment at different linear velocities of the wire during the patenting process and two different wear tests were performed, 2-body abrasive wear (grinding) and 3-body abrasive wear (rolling wear) tests. With an increasing linear velocity of the wire, the tensile strength and microhardness of the samples increased, whereas the interlamellar spacing in a pearlite structure decreased. The wear properties from the grinding and rolling wear tests exhibited an opposite tendency. The weight loss resulting from grinding was mainly affected by the tensile strength and microhardness, while the diameter loss obtained from rolling wear was affected by elongation or ductility of the samples. This result demonstrates that the wear mechanism in the 3-body wear test is much different from that for the 2-body abrasive wear test. The ultra-high tensile strength of the saw wire produced by the drawing process was attributed to the pearlite microstructure with very small interlamellar spacing as well as the high density of dislocation.

• 한국재료학회지
• /
• 제29권6호
• /
• pp.349-355
• /
• 2019

This study deals with the microstructure and tensile properties of 600 MPa-grade seismic reinforced steel bars fabricated by a pilot plant. The steel bar specimens are composed of a fully ferrite-pearlite structure because they were air-cooled after hot-rolling. The volume fraction and interlamellar spacing of the pearlite and the ferrite grain size decrease from the center region to the surface region because the surface region is more rapidly cooled than the center region. The A steel bar specimenwith a relatively high carbon content generally has a higher pearlite volume fraction and interlamellar spacing of pearlite and a finer ferrite grain size because increasing the carbon content promotes the formation of pearlite. As a result, the A steel bar specimen has a higher hardness than the B steel bar in all the regions. The hardness shows a tendency to decrease from the center region to the surface region due to the decreased pearlite volume fraction. On the other hand, the tensile-to-yield strength ratio and the tensile strength of the A steel bar specimen are higher than those of the B steel bar with a relatively low carbon content because a higher pearlite volume fraction enhances work hardening. In addition, the B steel bar specimen has higher uniform and total elongations because a lower pearlite volume fraction facilitates plastic deformation caused by dislocation slip.

• 열처리공학회지
• /
• 제31권5호
• /
• pp.231-236
• /
• 2018

The purpose of this study was to investigate the microstructural characteristics and hardness distribution of AZ91 magnesium alloy furnace-cooled to room temperature after solution treatment, and to compare the results with those of as-cast condition. The as-cast alloy showed a partially divorced eutectic ${\beta}(Mg_{17}Al_{12})$ phase and discontinuous precipitates (DPs) with a lamellar morphology, while only DPs were observed in the furnace-cooled alloy. The DPs in the furnace-cooled AZ91 alloy had various apparent interlamellar spacings, which would be ascribed to the different transformation temperatures during the furnace cooling. The average hardness for the furnace-cooled alloy is similar to that for the as-cast alloy. It is interesting to note that the hardness values of the furnace-cooled alloy were distributed over a narrower range than those of the as-cast alloy. This is likely to be caused by the relatively more homogeneous microstructure of the furnace-cooled alloy in comparison with the ascast one.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.271-272
• /
• 2008

This paper is concerned with the prediction of micro structural changes of pearlitic steel wire during clod drawing. The most important microstructural aspects are ferrite/cementite interlamellar spacing, cementite shape and thickness, since those are crucial factors to determine the mechanical strength of pearlitic steel. In this study, a couple of new algorithms to predict the above microstructural changes are developed based on the deformation histories of macro material points obtained from finite element simulations for pearlitic steel wire drawing. Some predictions are shown. The special features of the algorithms developed in this study are discussed in details.

• Bulletin of the Korean Chemical Society
• /
• 제25권7호
• /
• pp.965-968
• /
• 2004

H-montmorillonite was modified by interlayer surface silylation using 3-aminopropyltriethoxysilane and dodecylamine in ethanol without a pre-swelling step. Dodecylamine acts as a gallery expander and silylation catalyst. The evaporation of ethanol from the dispersion yields well-ordered silylated montmorillonites with large basal spacing between 1.50 and 4.20 nm. Solid-state $^29Si$ CP MAS NMR of the silylated samples showed $Q^2\;and\;Q^3$ signals as well as $T^2\;and\;T^3$ signals. The increase in the relative intensity of $Q^3\;for\;Q^2$ and the appearance of $T^2\;and\;T^3$ signals was attributed to the grafting of 3-aminopropyltriethoxysilane to the interlayer surface silanol groups.