• 폴리머
• /
• 제26권6호
• /
• pp.718-727
• /
• 2002

본 연구에서는 최종 복합재료의 기계적 계면특성을 향상시키기 위하여 산소 분위기 하에서 반응성 기체를 사용하는 이온 보조 반응법에 의해 탄소섬유 표면에 Ar+ 이온 빔을 조사하였다. 그리고, 단일 섬유 pull-out 시험을 실시하여 가해진 이온 에너지 세기에 대한 수지 내의 섬유의 뽑힘 정도를 측정한 후 Greszczuk의 .기하학적 모델에 기초하여 섬유/매트릭스 간의 계면특성을 알아보고자 하였다. 그 결과, 탄소섬유를 이온 빔으로 처리함에 따라 섬유와 매트릭스 간의 부착력 증가의 원인이 되는 섬유축 방향으로의 표면 etching 및 반응성 그룹이 형성되어 계면 전단강도가 향상되었으며 0.8 keV 이온 빔 세기에서 최대값을 나타내었다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.199-202
• /
• 2002

Interfacial properties and electrical sensing for fiber fracture in carbon and SiC fibers/epoxy composites were investigated by the electrical resistance measurement and fragmentation test. As fiber-embedded angle increased, interfacial shear strength (IFSS) of two-type fiber composites decreased, and the elapsed time was long to the infinity in electrical resistivity. The initial slope of electrical resistivity increased rapidly to the infinity at higher angle, whereas electrical resistivity increased gradually at small angle. Furthermore, both fiber composites with small embedded angle showed a fully-developed stress whitening pattern, whereas both composites with higher embedded angle exhibited a less developed stress whitening pattern. As embedded angle decreased, the gap between the fragments increased and the debonded length was wider for both fiber composites. Electro-micromechanical technique can be a feasible nondestructive evaluation to measure interfacial sensing properties depending on the fiber-embedded angle in conductive fiber reinforced composites.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 1999년도 추계학술발표대회 논문집
• /
• pp.28-31
• /
• 1999

Carbon fiber/epoxy composites using electrodeposited monomeric and polymeric coupling agents were compared with the dipping and the untreated cases. Treating conditions such as time, concentration and temperature were optimized. Four-fibers embedded micro-composites were prepared for fragmentation test. Interfacial properties of four-fiber composites with different surface treatments were investigated with simultaneous acoustic emission (AE) monitoring. The microfailure mechanisms occurring from fiber break, matrix and interlayer crackings were examined by AE parameters and an optical microscope. It was found that interfacial shear strength (IFSS) of electrodeposited carbon fibers was much higher than the other cases under dry and wet conditions. Well separated and different-shaped AE groups occurs for the untreated and ED treated case, respectively.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 추계학술발표대회 논문집
• /
• pp.116-120
• /
• 2001

Fiber fracture is one of the dominant failure phenomena to determine total mechanical properties in composites. Fiber fracture locations were measured by optical microscopic method and acoustic emission (AE) as functions of matrix toughness and surface treatment by the electrodeposition (ED), and then two methods were compared. Two AE sensors were attached on the epoxy specimen and fiber fracture signals were detected with elapsed time. The interfacial shear stress (IFSS) was measured using tensile fragmentation test and AE system. In ED-treated case, the number of the fiber fracture measured by an optical method and AE was more than that of the untreated case. The signal number measured by AE were rather smaller than the number of fragments measured by optical method, since some fiber fracture signals were lost while AE detection. However, one-to-one correspondence between the x-position location by AE and real break positions by optical method was generally established well. The fiber break source location using AE can be a valuable method to measure IFSS for semi- or nontransparent matrix composites nondestructively (NDT).

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.212-215
• /
• 2002

Interfacial evaluation and damage sensing of the carbon fiber/epoxy-amine terminated (AT)-polyetherimide (PEI) composites were performed using micromechanical test and electrical resistance measurement. As AT-PEI content increased, the fracture toughness of epoxy-AT-PEI matrix increased, and thus their interfacial shear strength (IFSS) was improved due to the improved toughness. After curing process, the changes in electrical resistance (ΔR) with increasing AT-PEI contents increased gradually because of the changes in thermal expansion coefficient (TEC) and thermal shrinkage of matrix. Matrix fracture toughness was correlated to the IFSS, residual stress and electrical resistance. The results obtained from the electrical resistance measurement during curing process, reversible stress/strain, and durability test were consistent with modified matrix toughness properties.

• Macromolecular Research
• /
• 제9권1호
• /
• pp.20-29
• /
• 2001

Interfacial adhesion and nondestructive behavior of electrodeposited (ED) carbon fiber rein-forced composites were evaluated using electro-micromechanical techniques and acoustic emission (AE). The interfacial shear strength (IFSS) of the ED carbon fiber/epoxy composites was higher than that of the untreated fiber. This might be expected because of the possibility of chemical or hydrogen bonding in an electrically adsorbed polymeric interlayer. The logarithmic electrical resistivity of the untreated single-carbon fiber composite increased suddenly to infinity when fiber fracture occurred, whereas that of the ED composite increased relatively gradually to infinity. This behavior may arise from the retarded fracture time due to enhanced IFSS. In single- and ten-carbon fiber composites, the number of AE signals coming from interlayer failure of the ED carbon fiber composite was much larger than that of the untreated composite. As the number of the each first fiber fractures increased in the ten-carbon fiber composite, the electrical resistivity increased stepwise, and the slope of the logarithmic electrical resistance increased.

• Composites Research
• /
• 제15권3호
• /
• pp.39-44
• /
• 2002

Micromechanical 시험법을 이용하여 전기증착된 탄소섬유와 polyetherimide (PEI)로 강인화된 에폭시 기지재료 사이의 계면물성과 미세파괴형상을 연구하였다. 계면전단강도 향상을 위해 전기증착법을 이용하여 탄소섬유를 표면 처리하였다. PEI 함량이 증가함에 따라 소성변형과 파괴인성 증가로 인해 계면전단강도는 점차적으로 증가하는 경향을 보였으며, 미처리의 경우에 순수 PEI의 계면전단강도가 가장 큰 값을 보였다. 반면 전기증착의 경우에 계면전단강도는 PEI를 첨가함에 따라서 증가하였지만 그 증가폭은 미처리의 경우 보다 작았다. 미처리의 경우에서 순수 에폭시는 취성파괴 형상을 보인 반면 순수 PEI는 연성파괴 형상을 보였고 전기증착의 경우 순수 에폭시는 미처리와는 달리 연성파괴 형상을 보임을 관찰할 수 있었다. PEI 첨가에 의한 파괴인성 강화와 전기증착에 의한 화학결함 및 계면층의 존재는 복합재료의 계면물성 향상에 효과적으로 기여하는 것으로 고려된다.

• Macromolecular Research
• /
• 제8권4호
• /
• pp.153-164
• /
• 2000

By electrodeposition (ED) using a monomeric- and two polymeric coupling agents, the interfacial shear strength (IFSS) of carbon fiber/epoxy composites was investigated by fragmentation test. ED results were compared with the dipping and the untreated cases under dry and wet conditions. Multi-fiber composites (MFC) were used for the direct comparison for the untreated and the treated cases. Various treating conditions including time, concentration and temperature were evaluated, respectively. Under dry and wet conditions ED treatment exhibited much higher IFSS improvement compared to the dipping and the untreated cases. Monomeric- and polymeric coupling agents exhibited the comparative IFSS improvement. Adsorption mechanism between coupling agents and carbon fiber was analyzed in terms of the electrolyte molecular interactions during ED process based on to the chain mobility. The microfailure modes occurring from the fiber break, matrix and interlayer cracks were correlated to IFSS.

• 접착 및 계면
• /
• 제14권2호
• /
• pp.75-81
• /
• 2013

SiC 나노입자를 이용하여 에폭시 복합재료를 제조할 수 있다. SiC 형상에 따른 영향으로 복합재료의 계면 물성이 변화된다. SiC의 형상에 따른 계면 상태의 변화를 관찰하기 위해 베타 형태, 위스커 형태의 SiC 나노입자를 사용하였다. 나노입자에 대한 분산도를 평가하기 위해 커패시턴스를 이용한 분산도 평가방법을 활용하였다. FE-SEM을 이용하여 SiC 나노입자의 활용에 따른 나노복합재료의 파단면을 관찰하여, 그 강화 효과를 비교 분석하였다. 탄소섬유와 SiC 나노입자가 함유된 에폭시를 이용한 복합재료에 계면 물성을 비교하기 위해 층간전단강도 평가법과 계면전단강도 평가법을 이용하였다. 복합재료의 계면 물성을 강화하기 위해서는 베타 형태의 SiC 나노입자를 활용할 경우가 위스커 입자를 이용한 경우보다 높은 계면 강도를 나타냈다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.92-95
• /
• 2004

Interfacial shear strength (IFSS) of environmentally- friend natural fiber reinforced polymer composites playa very important role in controlling the overall mechanical properties. In this work the IFSS of Ramie and Kenaf fibers/epoxy systems were evaluated using the combination of micromechanical technique, microdroplet test to find out an optimal condition in accordance with final purpose by comparing to each other. Clamping effect on fiber elongation was determined as well. In addition, the mechanical properties of the natural fibers were investigated using single fiber tensile test and analyzed statistically by both uni- and bimodal Weibull distributions. Microfailure modes of different natural fiber structures were observed using optical microscope.