• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.3
• /
• pp.359-364
• /
• 2013

In order to use a linear vibration motor for the actuator of a haptic interface, the motor must provide a higher reaction rate and longer service life than typical rotational motors with an eccentric mass. In this paper, we propose a linear vibration motor that is equipped with a voice-coil actuator and permanent-magnet springs. To concentrate the magnetic flux in the actuator, a Halbach-style magnetization pattern is used. Permanent-magnet springs replace mechanical springs to help increase the service life. We use the method of equivalent current sheets and the method of images to analyze and model the proposed vibration motor. These methods are validated using finite element analyses and experiments. A prototype motor is designed and fabricated. Tests with the prototype show the feasibility of the proposed linear vibration motor.

• Journal of Welding and Joining
• /
• v.31 no.5
• /
• pp.54-58
• /
• 2013

Joint properties of vehicle ECU (Electric Control Unit) module which was manufactured by using Sn-Cu-Cr-Ca alloy were investigated. A new solder which has a middle melting temperature about $231^{\circ}C$ was fabricated as the type of 300um solder ball and paste type. The prototype modules were made by reflow process and measured spreadability, wettability shear strength and estimated interface reaction. The spreadability of the alloy was about 84% from the measurement of contact angle of the solder ball and the wetting force was measured 2mN. The average shear strength of the module which was manufactured by using the solder paste, was 1.9 $kg/mm^2$. Also, the thickness of IMC(intermetallic compound) was evaluated with various aging temperature and time in order to understand Cr effect on Sn-0.7Cu solder. $Cu_6Sn_5$ IMC was formed between Cu pad and the solder alloy and the average thickness of the $Cu_6Sn_5$ IMC was measured about 4um and it was about 50% of thickness of $Cu_6Sn_5$ IMC in Sn-0.7Cu. It is expected to have a positive effect on reliability of the solder joint.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.362-363
• /
• 2012

A new cross-linkable polymer, cross-linked d-PBAB, which has the triphenylamine as the hole transporting moiety and ethynyl group as the thermal cross-linker is firstly synthesized by the combination of anionic polymerization and deprotection process. The thermal cross-linking reaction was performed at $240^{\circ}C$ for 50 min and cross-linked d-PBAB layer showed smooth surface and is not soluble at organic solvent under spin-coating of emitting layer (EML). The solution-processed PLED which was fabricated with cross-linked d-PBAB as HTL showed approximately two times higher Lmax and four times higher LEmax than those obtained from PLED with PEDOT:PSS as the HTL. These result is ascribed to better ability of cross-linked d-PBAB to block electrons and to prevent exciton-quenching than those of PEDOT : PSS at the EML interface. This results strongly suggested that cross-linked d-PBAB can be a promising material to replace conventional PEDOT : PSS. It can be suspected that PLEDwith cross-linked d-PBAB would show longer lifetime compared with that of PLED with PEDOT : PSS, and thus further studies are under investigation.

• Applied Microscopy
• /
• v.29 no.3
• /
• pp.281-289
• /
• 1999

The stirred and thixoformed $SiC_p/AZ91HP$ Mg composites are studied on the basis of microstructural analysis using transmission electron microscopy (TEM). The products of interfacial reaction are identified as $Mg_2Si$, MgO and $Mg_{17}Al_{12}$ phases and the crystallized phases are found to be orthorhmbic $Al_6Mn$ and decagonal T phases. It is shown that $Mg_2Si$ and $Mg_{17}Al_{12}$ phases are found at the surface of $SiC_p$ and $Al_6Mn$ is found near interface and crystallized on the matrix. Phase identification is carried out by crystallographic work based on primitive cell volume, zero order Laue zone (ZOLZ) patterns and single convergent beam electron diffraction (CBED) patterns containing higher order Laue zone ring from a nanosized region.

• Korean Journal of Computational Design and Engineering
• /
• v.20 no.1
• /
• pp.65-74
• /
• 2015

Structure and/or fluid analysis is gradually increased by an essential design process in the small and medium-sized businesses (SMBs) because of the needs for a rapid design process and the certification about the supplement of the parts by the large business (LB). In this paper, we developed the web-based ezSIM platform installed in the resources integrated system server. The ezSIM platform is based on the heterogeneous linux and windows operating system for the user-friendly connection with the part of the analysis for the SMBs. The procedure of the structure/fluid analysis service module using the public software and the license-free open code in the ezSIM platform was explained. The convenience of the ezSIM platform service was presented by the reaction rate of the graphic motion compared with that of a local PC and the solving and pre-post processing interface compared with that of the KISTI supercomputer. The web-based ezSIM platform service was identified as a useful and essential platform to the SMBs for the usage of the structure and/or fluid analysis procedure.

• Korean Journal of Materials Research
• /
• v.30 no.8
• /
• pp.426-434
• /
• 2020

The performance characteristics of a lead acid battery are investigated with the content of Sodium Perborate Tetrahydrate (SPT, NaBO₃·4H₂O) in a positive plate active material. SPT, which reacts with water to form hydrogen peroxide, is applied as an additive in the positive plate active material to increase adhesion between the substrate (positive plate) and the active material; this phenomenon is caused by a chemical reaction on the surface of substrate. A positive plate with the increasing content of SPT is prepared to compare its properties. It is confirmed that the oxide layer increases at the interface between the substrate and the active material with increasing content of SPT; this is proven to be an oxide layer through EDS analysis. Battery performance is confirmed: when SPT content is 2.0 wt%, the charging acceptance and high rate discharge properties are improved. In addition, the lifetime performance according to the Standard of Battery Association of Japan (SBA) S0101 test is improved with increasing content of SPT.

• Journal of the Korean institute of surface engineering
• /
• v.47 no.2
• /
• pp.75-80
• /
• 2014

Nanocrystalline diamond(NCD) films on steel(SKH51) has been investigated using SiC interlayer film. SiC was deposited on SKH51 or Si wafer by RF magnetron sputter. NCD was deposited on SiC at $600^{\circ}C$ for 0.5~4 h employing microwave plasma CVD. Film morphology was observed by FESEM and FIB. Film adherence was examined by Rockwell C adhesion test. The growth rate of NCD on SiC/Si substrate was much higher than that on SiC/SKH51. During particle coalescence, NCD growth rate was slow since overall rate was determined by the diffusion of carbon on SiC surface. After completion of particle coalescence, NCD growth became faster with the reaction of carbon on NCD film controlling the whole process. In the case of SiC/SKH51 substrate, a complete NCD film was not formed even after 4 h of deposition. The adhesion test of NCD/SiC/SKH51 samples revealed a delamination of film whereas that of SiC/SKH51 showed a good adhesion. Many voids of less than 0.1 ${\mu}m$ were detected on NCD/SiC interface. These voids were believed as the reason for the poor adhesion between NCD and SiC films. The origin of voids was due to the insufficient coalescence of diamond particles on SiC surface in the early stage of deposition.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.3
• /
• pp.151-160
• /
• 1999

The settlement limit concept is generally adopted as design criteria of rock-socketed pile foundations, therefore, the load-displacement$(\sigma-\sigma)$ behavior of the rock-socketed piles should be well understood at the design stage, which, however, is hard to achieve due to its complexity. To help this out, field pile load tests are executed on cast-in-situ concrete piles, first, to figure out the $\sigma$-$\delta$ behavior of rock-socketed piles. Next, the $\sigma-\sigma$ relations of the piles are simulated numerically using commercial package program(ELAC) varying a couple of input data which are sensitive in shaping the $\sigma$-$\delta$ curves. Finally, the relation between the best input data for the numerical simulations and the geotechnical field data are cultivated to generalize the numerical simulation procedures, which enables geotechnical engineers to predict the $\sigma$-$\delta$ behavior at the design stage, if appropriate geotechnical field data are provided.

• Journal of Digital Contents Society
• /
• v.19 no.1
• /
• pp.113-122
• /
• 2018

In level 3 automated vehicles, drivers are expected to encounter transition of control when the system reaches its limit. Drivers need to refocus their attention on the road ahead and gain situational awareness. Appropriate information should be conveyed during this period in order to prevent human errors. In this paper, we defined the takeover process as 'in-the-middle-of-the-loop' and conducted Task Analysis and Work Domain Analysis to find out information requirements. As a result, we specified required information types and interface considerations. Moreover, we conducted an experimental study to find how the information types affect drivers on situation awareness, cognitive load and reaction time. Consequently, we found different information on system transparency should be conveyed depending on the urgency of takeover situation and driver guidance could help drivers with better situation awareness after the takeover.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.4 no.1
• /
• pp.43-51
• /
• 2010

In this paper, we developed a digital Taekwondo trainer system based on the electronic protector was authorized by the World Taekwondo Federation for the improvement of user's training effects and athletic performances. Our system consists of E-Kick Bag with sensors for sensing hits, taekwondo trainer program and receiver for interconnection of E-kick Bag to program. Taekwondo trainer system also has an advantage to improve training effects and athletic performances such as hit-accuracy and reaction velocity by appointing a hitting target for users with 6 LED indicators. The taekwondo trainer program is a user interface to provide training courses such as progress training of response time and stamina, preparation training for real sparring by training scenario. It has also characteristics which are to strengthen and supplement user's pros and cons by analyzing hitting intensity and accuracy from training. In this paper, we implemented a test targeting eight taekwondo players on the playing list include a member of the Korea national team and conducted a survey in order to evaluate the utility of our system.