• Bulletin of the Society of Naval Architects of Korea
• /
• v.19 no.4
• /
• pp.19-29
• /
• 1982

Galerkin's finite element method is applied to a two-dimensional heat convection-diffusion problem arising in the hydrodynamic lubrication of thrust bearings used in naval vessels. A parabolized thermal energy equation for the lubricant, and thermal diffusion equations for both bearing pad and the collar are treated together, with proper juncture conditions on the interface boundaries. it has been known that a numerical instability arises when the classical Galerkin's method, which is equivalent to a centered difference approximation, is applied to a parabolic-type partial differential equation. Probably the simplest remedy for this instability is to use a one-sided finite difference formula for the first derivative term in the finite difference method. However, in the present coupled heat convection-diffusion problem in which the governing equation is parabolized in a subdomain(Lubricant), uniformly stable numerical solutions for a wide range of the Peclet number are obtained in the numerical test based on Galerkin's classical finite element method. In the present numerical convergence errors in several error norms are presented in the first model problem. Additional numerical results for a more realistic bearing lubrication problem are presented for a second numerical model.

• Geotechnical Engineering
• /
• v.12 no.3
• /
• pp.35-48
• /
• 1996

Reinforced soil structures may experience large local movements between soil and reinforcement. The failure modes of a reinforced structure depend on several factors which are governed by deformation and slipping of the reinforcement. In some cases, pulling out of the reinforcement may occur instead of rupturing, The growing use of geosynthetic liner system for storage of solid and liquid wastes has led to a number of slope instability problems where the synthetic liner may undergo a large amount of stretching and slipping as a result of the loading. The conventional finite element model for the soil-reinforcement interface uses a zero thickness joint element with normal and shear stiffnesses and can only accommodate a small amount of deformation. When a large slippage occurs, the model provides an i ncorrect mechanism for deformation. This paper presents a new interface finite element model which is able to simulate a large amount of slippage between soil and reinforcement. The formulation of the model is presented and the capability of the model is demonstrated using illustrative examples.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.20 no.1
• /
• pp.37-44
• /
• 2017

Complexity of multiphase flows due to existence of more than two interface including free-surface in one system, cannot be simulated easily. Since more than two fluids affect to flows and disturb interface, non-linearities such as instabilities can be appeared. Among several instabilities on multiphase flows, one of representative is Rayleigh-taylor instability. In order to examine in importance of density disparity, several cases with numerous Atwood number are set. Moreover, investigation of influence on initial disturbance were also considered. Moving particle simulation (MPS) method, which was employed in this paper, was not widely used for multiphase problem. In this study, by adding new particle interaction models such as self-buoyance correction, surface tension, and boundary condition at interface models, MPS were developed having more strength of physics and robust. By applying newly developed multiphase MPS, considered cases are performed and compared each other. Additionally, though existence of disagreement of magnitude of rising velocity between theoretical values from linear potential theory and that of numerical simulation, agreement of tendency can be proved of similarity of result. the discordance of magnitude can be explained due to non-linear effects on numerical simulation which was not considered in theoretical result.

• 한국전산유체공학회:학술대회논문집
• /
• 2004.03a
• /
• pp.178-182
• /
• 2004

Numerical analysis of a gaseous jet submerged in a liquid environment was carried out using the volume of fluid(VOF) method to simulate the kinematics of the gas-liquid interface. Two nozzle geometries were tested, one for Fanno tube and the other for converging diverging nozzle. Commercial code was used for the present calculation. Transient behavior of a gaseous jet since its start showed periodic nature of the jet, which was also observed in previous measurements.

• Transactions on Electrical and Electronic Materials
• /
• v.13 no.4
• /
• pp.188-191
• /
• 2012

This paper introduces a new method regarding deuterium incorporation in the gate dielectric including deuterium implantation and post-annealing at the back-end-of-the process line. The control device and the deuterium furnace-annealed device were also prepared for comparison with the implanted device. It was observed that deuterium implantation at a light dose of $1{\times}10^{12}-1{\times}10^{14}/cm^2$ at 30 keV reduced hot-carrier injection (HCI) degradation and negative bias temperature instability (NBTI) within our device structure due to the reduction in oxide charge and interface trap. Deuterium implantation provides a possible solution to enhance the bulk and interface reliabilities of the gate oxide under the electrical stress.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.1
• /
• pp.18-25
• /
• 1984

The transition boiling of a liquid droplet on a heated flat surface was studied utilizing Kotake's model with the effects of viscosity of a thin vapor layer between the droplet and the hot plate taken into account. This problem was analyzed considering the process of the droplet evaporation which resulted in hydrodynamic instability at the liquid-vapor interface. The results of the study are as follows; (1)The effect of the viscosity in the vapor layer at the interface appears as a dimensionless number N, namely .sigma. .delta.$_{0}$ /.rho.nu.$^{2}$ (2)The time required for evaporation at the transitional region increases with the temperature difference ratio .DELTA. T$_{r}$. The rate of increase of the total evaporation time becomes larger as increasing of N$_{m}$(N number at maximum heat flux) increases.s.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.1
• /
• pp.16-21
• /
• 2015

In this study, the effects of forming gas post metallization annealing (PMA) on recessed AlGaN/GaN-on-Si MOSHFET were investigated. The device employed an ICPCVD $SiO_2$ film as a gate oxide layer on which a Ni/Au gate was evaporated. The PMA process was carried out at $350^{\circ}C$ in forming gas ambient. It was found that the device instability was improved with significant reduction in interface trap density by forming gas PMA.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.6
• /
• pp.316-319
• /
• 2017

A new approach to improving the electrical characteristics and optical response of a polysilicon-based metal-semiconductor-metal (MSM) photodetector is proposed. To understand the cause of current restriction in the MSM photodetector, modified trap mechanisms are suggested, which include interfacial electron traps at the metal/polysilicon interface and silicon dangling bonds between silicon crystallite grains. Those traps were passivated using hydrogen ion implantation with subsequent post-annealing. Photodetectors that were ion-implanted under optima conditions exhibited improved photoconductivity and reduced dark current instability, implying that the hydrogen bonds in the polysilicon influence the simultaneous decreases in the density of dangling bonds at grain boundaries and the trapped positive charges at the contact interface.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.4
• /
• pp.484-492
• /
• 2011

Power system analyses, which involve the handling of massive data volumes, necessitate the use of effective visualization methods to facilitate analysis and assist the user in obtaining a clear understanding of the present state of the system. This paper introduces an interface that compensates for the limitations of the visualization modules of dynamic security assessment tools, such as PSS/e and TSAT, for power system variables including generator rotor angle and frequency. The compensation is made possible through the automatic provision of dynamic simulation data in visualized and tabular form for better data intuition, thereby considerably reducing the redundant manual operation and time required for data analysis. The interface also determines whether the generators are stable through a generator instability algorithm that scans simulation data and checks for an increase in swing or divergence. The proposed visualization methods are applied to the dynamic simulation results for contingencies in the Korean Electric Power Corporation system, and have been tested by power system researchers to verify the effectiveness of the data visualization interface.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1993.11a
• /
• pp.3-3
• /
• 1993

In mechanical testing of W-Ni-Pe heavy alloys, the cracks nucleate at W/W interface and propagate through W/ Imatrix interface or through matrix phase together with the cleavage of W grains. The mechanical properties can therefore be improved by control of the interfacial strength and area. In this presentation, some experimental result and techniques on this subject will be reviewed and discussed. The hydrogen embrittlement caused by the hydrogen segregation at interfaces during sintering in an hydrogen atmosphere can be removed by an heat-treattnent in vacuum or in an inert atmosphere. The heat-treatment condition can be estimated by using a diffusion equation for a cylindrical shape. The mechanical properties, in particular the impact property, are degraded by the segregation of non-metallic impurities, such as Sand P. The degradation can be prevented by adding a fourth element, such as La or Ca, active with the non-metallic impurities. The cyclic heat-treatment at usual heat-treattnent tempemture causes the penetration of matrix between W/W grain boundaries and results in remarkable increase in impact energy. This is due to an increase in the area of ductile failure during the impact test. The instability of W/matrix interface casued by addition of Mo or Re can be controlled by using W powders of different size. The increase in the interfacial area in found to be related to the presence of non-equilibrium pure W gmins among W(Mo or Re) solid solution gmins.