• 상하수도학회지
• /
• 제18권3호
• /
• pp.337-342
• /
• 2004

Previous experiment was performed under abiotic condition. Steady-state abiotic experiments in the sand-tank reactor with air flowing through the reactor headspace demonstrated that oxygen supply through the water table interface into the saturated zone was enhanced when an LNAPL (dodecane) pool was present at the water table. Biotic condition was considered in this study. Biotic experiments performed after inoculating the reactor with Pseudomonas putida mt-2, which does not grow on dodecane, indicated that the enhanced oxygen supply in the presence of the LNAPL pool also enhanced biodegradation of a solute (glucose) plume passing beneath the LNAPL pool at steady-state.

• Tribology and Lubricants
• /
• 제18권2호
• /
• pp.117-126
• /
• 2002

Abstract - An integrated condition monitoring algorithm based on an expert system was implemented in this work in order to monitor effectively the machine conditions. The knowledge base was consisted of numeric data which meant the posterior probability of each measurement parameter for the representative machine failures. Also the inference engine was constructed as a series of statistical process, where the probable machine fault was inferred by a mapping technology of pattern recognition. The proposed algorithm was, through the user interface, applied for an air compressor system where the temperature, vibration and wear properties were measured simultaneously. The result of the case study was found fairly satisfactory in the diagnosis of the machine condition since the predicted result was well correlated to the machine fault occurred.

• 대한기계학회논문집A
• /
• 제25권6호
• /
• pp.1023-1030
• /
• 2001

The tensile properties of short nylon6 fiber reinforced NR and SBR have been investigated as functions of diameter ratio(DR), interphase condition, fiber aspect ratio(AR), and fiber content. The short-fiber(DR=3 and AR=2) reinforced SBR did not show the dilution effect for all interphase conditions. And the short-fiber(DR=3 and AR=2) reinforced NR did not show the dilution effect except for the no-coating. The better interphase condition, the lower dilution effect at same DR. The tensile moduli are significantly improved due to fiber content and diameter ratio at same interphase condition. The pull-out force increased with the DR. The better interphase condition, the higher pull-out force at same DR. It is found that the DR and AR have an important effect on tensile properties.

• 대한안전경영과학회지
• /
• 제15권4호
• /
• pp.171-178
• /
• 2013

Workers are avoiding production/manufacturing sites due to the poor working environment and concern over safety. Small and medium-sized businesses introduce new equipment to secure safety in the production site or ensure effective process management by introducing the real-time monitoring technique for existing equipment. The importance of real-time monitoring of equipment and process in the production site can also be found in the ANSI/ISA-195 model. Note, however, that most production sites still use paper-based work slip as a process management technique. Data reliability may deteriorate because information on the present condition of the production site cannot be collected/analyzed properly due to manual data writing by the worker. This paper introduces the monitoring and process management technique based on a direct facility interface to secure safety in the field by improving the poor working environment and enhance there liability and real-time characteristics of the production data. Since the data is collected from equipment in real-time directly through the SIB-based interface and PLC-based interface, problems associated with workers' manual data input are expected to be solved; safety can also be improved by enhancing workers' attention to work by minimizing workers' injuries and disruption.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1994년도 추계학술대회
• /
• pp.71-74
• /
• 1994

In cementless total hip arthroplasty(THA), an initial stability of the femoral component is mandatory to achieve bony ingrowth and secondary long term fixation. Bone ingrowth depends strongly on relative micromotion and stress distributions at the interface. Primary stability of the femoral component can be obtained by minimizing the magnitude of relative micromotions at bone-prosthesis interface, Hence an accurate evaluation of interface behavior and stress/strain fields in the bone implant system may be relevant for better understanding of clinical situations and improving THA design. However, complete evaluation of load transfer in the bone remains difficult to assess experimentally, Hence, recently finite element method (FEM) was introduced in orthopaedic research field to fill the gap due to its unique capacity to evaluate stress in structure of complex shape, loading and material behavior. The authors developed the 3-dimensional numerical finite element model which is composed of totally 1179 elements off and 8 node blick. We also analyzed the micromotions at the bone-stem interface and mechanical behavior of existing bone prosthesis for a loading condition simulating the single leg stance. The result indicates that the values of relative motion for this well fit Multilock stem were $150{\mu}m$ in maximum, $82{\mu}m$ in minimum, and the largest relative motion developed in medial region of proximal femur with anterior-posterior direction. The proximal region of the bone was much larger in motion than the distal region and the stress pattern shows high stress concentration on the cortex near the tip of the stem. These findings indicates that the loading in the proximal femoral bone in the early postoperative situation can produce micromotions on the interface and clinically cementless TEA patient should not be allowed weight bearing strictly early in the postoperative period.

• 콘크리트학회논문집
• /
• 제25권1호
• /
• pp.81-90
• /
• 2013

이 연구에서는 합성보의 수평 접합면에 대한 수평전단력 저항성능을 평가하기 위하여 6개의 접합면 전단성능 실험체를 대상으로 접합면의 표면상태, 전단철근의 보강량과 상세 등의 구조변수에 대한 수평전단강도를 평가하였다. 휨압축파괴를 나타낸 SF-291B를 제외한 모든 실험체는 실험계획에서 의도한 대로 접합면의 수평전단력에 의한 전단파괴를 나타내었다. 설계기준식의 수평전단력 전달 또는 전단마찰 설계법으로 산정한 접합면 전단강도는 실험체의 수평전단 파괴를 초래한 접합면의 수평전단내력을 양호한 수준으로 평가하는 것으로 나타났으며, PCI 설계기준에서 제시한 전단철근의 배근상세와 정착길이는 접합면에서 요구되는 수평전단성능을 확보할 수 있다고 판단된다.

• 비파괴검사학회지
• /
• 제32권4호
• /
• pp.393-400
• /
• 2012

최근 나노 박막은 MEMS/NEMS, 광학 코팅, 반도체 산업 등 다양한 분야에서 사용이 되고 있다. 박막은 마모, 침식, 부식, 고온 산화를 방지하기 위한 목적으로 사용될 뿐 아니라 특성화된 자기, 유전적 특성을 만들기 위한 목적으로 사용된다. 많은 연구자들이 이러한 박막 구조의 특성(밀도, 입자 크기, 탄성 특성, 필름/기지 계면의 특성)을 평가하기 위하여 많은 연구를 진행하고 있다. 이들 중에 박막과 기지 사이의 접합 특성을 평가하는 것이 많은 연구자들의 주 관심사가 되어 왔다. 본 연구에서는 나노 박막의 접합 특성을 평가하기 위하여 각기 다른 접합 특성을 가지는 폴리머 박막 시험편을 제작하였다. 제작된 시험편의 접합 특성을 측정하기 위하여 초음파현미경의 V(z) 곡선법을 이용하여 표면파의 속도를 측정하였다. 또한 계면을 포함하는 시험편의 표면을 전파하는 표면파의 속도와 접합력의 상관관계를 확인하기 위해 나노 스크래치 시험을 적용하였다. 그 결과 초음파현미경을 이용하여 측정된 표면파의 속도와 나노스크래치 시험을 이용한 임계하중이 일치하는 경향성을 나타내었다. 결론적으로 초음파현미경의 V(z) 곡선법은 나노 스케일 박막 계면에서의 접합 상태를 평가할 수 있는 기법으로 그 가능성을 나타내었다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.951-956
• /
• 2011

As the evaluation of loading characteristic on tilting mechanism is the most important one of the function test of tilting mechanism, the changing characteristic of load must be investigated on tilting of carbody for both the static and running condition of train. In this study, we reduced the load of tilting mechanism by adjusting the interface of carbody and bogie such as the weight balance, level of underframe, height of leveling valve, height of axle box and center position of tilting actuator with the characteristic curve of load for optimal condition of the tilting mechanism obtained in the previous study. Furthermore, the factor and effect of the interfacial structures respecting the load of tilting mechanism was evaluated by analyzing the changing characteristic of load obtained in the process of adjustment of interfaces. From these data, we will propose the maintenance standards for interfacial structures and tilting mechanism in order to minimize the load of tilting mechanism by analyzing in detail the characteristic of load for the main factors of the interfacial structure effecting on the load of tilting mechanism.

• 소성∙가공
• /
• 제27권5호
• /
• pp.267-275
• /
• 2018

The clad sheet material is produced by a roll-bonding process of one or more materials with different properties. Good formability of clad sheet material is an essential property in to deform a clad metal sheet into a part or component. Performance of the clad sheet material largely depends on interfacial bond strength between different materials. In this study, interfacial bond strength of STS/Al clad sheet was analyzed by varying experimental parameters using a blanking process. Experimental parameters are the punching speed, clearance, and stacking order of plate materials. In addition, blanking test results were compared with bond strengths measured by the T-peel test, that analyzes interface bonding strength of the standard clad sheet. The blanking process was analyzed by the finite element method under the sticking condition of interface of different materials, and experimental results and analysis results were compared.

• 한국전산유체공학회지
• /
• 제21권1호
• /
• pp.110-116
• /
• 2016

The present study numerically investigated the deformation of the interface of two-phase fluids flow in a blast furnace. To simulate three-dimensional(3D) incompressible viscous two-phase flow in the furnace filled with the air and molten iron, the volume of fluid(VOF) method based on the finite volume method has been utilized. In addition, the porous medium with the porosity has been considered as the bed of the particles such as cokes and char etc. For the comparison, the single phase flow and the two-phase flow without the porosity have been simulated. The two-phase flow without porosity condition revealed the smooth parabolic profile of the free surface near the outlet. However, the free surface under the porosity condition formed the viscous finger when the free surface was close to the outlet. This viscous finger accelerated the velocity of the free surface falling and the outflow velocity of the fluids near the outlet.