• Journal of Ocean Engineering and Technology
• /
• v.23 no.2
• /
• pp.8-17
• /
• 2009

This paper presents an adaptive tracking control method for a welding mobile manipulator with several unknown parameters such as the last length of the manipulator, the wheel radius and the distance from the center to the wheel. The mobile manipulator consisted of the manipulator and the mobile-platform. Kinematic modelings for the manipulator and the mobile-platform with several unknown parameters were produced. The tracking error vectors for the manipulator and the mobile-platform were defined. These adaptive controllers were designed based on the Lyapunov function to guarantee the stability of the whole system when the mobile manipulator performs a welding task. Update laws were also designed to estimate the unknown dimensional parameters. To implement the designed controllers, a control system integrated with PIC16F877 microprocessors and a TMS320C32 DSP was developed. Simulation and experimental results are presented to show the effectiveness of the proposed controllers.

• Tribology and Lubricants
• /
• v.27 no.3
• /
• pp.125-133
• /
• 2011

The purpose of this study is to develop an engine oil quality monitoring system to warn the abnormal condition of engine oil. To do this, first of all, it is needed a personal controller development to measure the capacitance of a pre-developed engine oil deterioration detection sensor integrated with an oil filter. To measure the capacitance of engine oil in the sensor, it is used the way measuring the electric charging time in a capacitor by impressing DC volt. This method has merits on cost and signal stability. The measured capacitance is compensated by comparing with the one measured by an impedance analyzer. Also, using the dielectric constant gained by an impedance analyzer, the calculating equation of the dielectric constant of engine oil related with the currently developed sensor is decided. Then, the deterioration degree of engine oil is estimated according to the change rate of dielectric constant between green oil and used oil. Finally, using this dielectric constant information together with engine oil temperature and pressure, the currently developed engine oil quality monitoring system is to tell the abnormal state of engine oil.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.5
• /
• pp.959-966
• /
• 2020

With the growing importance of the fishery industry and the rapid growth of the aquaculture industry, research on smart farms through ICT convergence in the aquaculture field is in progress. To enable monitoring of the growing environment at the farm site, an underwater drone drive unit, an image collection device, an integrated controller for posture stabilization, and a remote control device capable of controlling and controlling drones through real-time underwater images were proposed, and design, development, and tests were conducted. By utilizing underwater drones, it is possible to replace the supply and demand of manpower and high-cost work in the aquaculture industry, and to manage fish farms in a stable manner by reducing the probability of farming deaths.

• Proceedings of the KIPE Conference
• /
• 2001.12a
• /
• pp.23-26
• /
• 2001

This paper presents a digital motion control system for Reluctance Synchronous Motor (RSM) drives with direct torque control (DTC). The system consists of stator flux observer, torque estimator: two hysteresis band controllers, an optimal switching look-up table, IGBT voltage source inverter(VSI), and TMS320C31 DSP controller by using fully integrated control software. The stator flux observer is based on the combined voltage and current model with stator flux feedback adaptive control of which inputs are current, voltage and actual rotor angle for wide speed range. In order to prove the suggested motion control algorithm, There are some simulation and testing at actual experimental system. The developed digitally high-performance motion control system are shown a good motion control response characteristic results and high performance features using 1.0Kw RSM.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.7
• /
• pp.147-154
• /
• 2003

An effective die-polishing robot system is developed. ATC (Automatic Tool Change), tool posture angle control, and robot program for polishing application are developed and integrated into a robotic system that consists of a robot, pneumatic grinding tool, and grinding abrasives (papers and special films). ATC is specifically designed to exchange whole grinding tool set for complete unmanned operation. A tool posture angle control system is developed for the tools to maintain a specified skew angle rather than right angle on the surface for best finishing results. A PC and the robot controller control ATC and tool posture angle. Also, there have been more considerations on enhancing the performance of the system. Elastic material is inserted between the grinding pad and the holder for better grinding contact. Robot path data are generated automatically from the NC data of previous machining process.

• Journal of Korea Society of Industrial Information Systems
• /
• v.19 no.3
• /
• pp.25-30
• /
• 2014

This paper describes the design of gate driver circuits in distributed maximum power point tracking(DMPPT) controller for photovoltaic system. For the effective DMPPT control in the existence of shadowed modules, high voltage gate driver is applied to drive the DC-DC converter in each module. Some analog blocks such as 12-b ADC, PLL, and gate driver are integrated in the SoC for DMPPT. To reduce the power consumption and to avoid the high voltage damage, a short pulse generator is added in the high side level shifter. The circuit was implemented with BCDMOS 0.35um technology and can support the maximum current of 2A and the maximum voltage of 50V.

• Journal of the Korean Society of Safety
• /
• v.21 no.4 s.76
• /
• pp.25-32
• /
• 2006

LonWorks over IP(LonWorks-IP) virtual device network(VDN) is an integrated form of LonWorks device network and IP data network. In especially real-time distributed servo applications on the factory floor, timely response is essential for predictive and preventive maintenance. The time delay in servo control on LonWorks-IP based VDN has highly stochastic nature. LonWorks-IP based VDN induced transmission delay deteriorates the performance and stability of the real-time distributed control system and can't give an effective preventive and predictive maintenance. In order to guarantee the stability and performance of the system, and give an effective preventive and predictive maintenance, LonWorks-IP based VDN induced time-varying uncertain time delay needs to be predicted and compensated. In this paper new Pill control scheme based on Smith predictor, disturbance observer and band pass filter is proposed and tested through computer simulation about position control of DC servo motor. It is shown that how can the proposed control scheme be designed to minimize the effects of uncertain varying time delay and model uncertainties. The validity of the proposed control scheme is compared and demonstrated with the comparison of internal model controllers(IMC) based on Smith predictor with and without disturbance observer.

• Journal of the Korean Society of Industry Convergence
• /
• v.19 no.1
• /
• pp.42-49
• /
• 2016

This study proposes a non-contact inspective technology based robot vision system for Faulty Inspection of welding States and Parts Shape. The maine focus is real time implementation of the machining parts' automatic inspection by the robotic moving. For this purpose, the automatic test instrument inspects the precision components designator the vision system. pattern Recognition Technologies and Precision Components for vision inspection technology and precision machining of precision parts including the status and appearance distinguish between good and bad. To perform a realization of a real-time automation integration system for the precision parts of manufacturing process, it is designed a robot vision system for the integrated system controller and verified the reliability through experiments. The main contents of this paper, the robot vision technology for noncontact inspection of precision components and machinery parts is useful technology for FA.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.4
• /
• pp.86-92
• /
• 2009

A driver-vehicle model means the integrated dynamic model that is able to estimate the steering wheel angle from the driver's desired path based on the dynamic characteristics of the driver and vehicle. Autonomous driving robot for factory automation has individual four-wheels which are driven by electronic motors. In this paper, the dynamic characteristics of several four-wheel steering systems with the simultaneously steerable front and rear wheels are investigated and compared by means of the driver-vehicle model. A diver-vehicle model is proposed by using the PID control to velocity and trajectory of control autonomous driving robot. To determine the optimum speed of a autonomous driving robot, steady-state circle simulation is carried out with the ADAMS program and MATLAB control model.

• Proceedings of the Korea Technology Innovation Society Conference
• /
• 2000.05a
• /
• pp.154-173
• /
• 2000

Since computerized numerical controller (CNC) emerged as a result of the fusion of the electronics technology and the mechanical technology, there has been continuous evolution of CNC technology in the mechatronics industry. The industry is recently developing a new control system based on the fusion of personal computer (PC) and CNC. Upgraded PC has now integrated into CNC, making various machines possible to exchange data, software and hardware, and to greatly improve man-machine interface. The fusion of PC and CNC can form a new paradigm in technological innovation of not only control system but also whole machinery industry in near the future. Korea lagged behind the developed countries in the development of open control system with the fusion of PC. Turbo-tek, Hyundai Motor and Daewoo are leading companies, but their commercial possibility seems to be low because domestic market is too small to reap a commercial benefit. Nevertheless, the development of the system is an essential step for Korea to embark on a future technological paradigm of the machinery industry. The government needs to play some role for the development, for instance, government R&D projects, institutional building and training of related technicians.