• Clean Technology
• /
• v.18 no.4
• /
• pp.446-450
• /
• 2012

Strong alkaline electrolyzed water which is produced in cathode by electrolyzing the solution where electrolytes (NaCl, $K_2CO_3$ etc.) are added in diaphragm electrolytic cell, is eco-friendly and has cleaning effects. So, it is viewed as a substitution of chemical cleaner. In addition, strong alkaline electrolyzed water is being used by some Japanese automobile and precision parts manufacturing industries. When strong alkaline electrolyzed water is produced by using diaphragm electrolytic cell, it is necessarily produced at the anode side. Since strong acidic electrolyzed water produced is discarded when its utilization cannot be found, production efficiency of electrolyzed water is consequently decreased. Also, there is a weakness electrolytic efficiency is decreasing due to the pollution of diaphragm. In order to overcome this, non-diaphragm all-in-one electrolytic cell integrated with electrode reaction chamber and dilution chamber was applied. Strong alkaline electrolyzed water was produced for different composition of electrolytes, and their properties and characteristics were identified. In comparing the properties between strong alkaline electrolyzed water produced in diaphragm electrolytic cell and that produced in all-in-one electrolytic cell, the differences in ORP and chlorine concentration were found. In emulsification test to confirm surface-active capability, similar results were obtained and strong alkaline electrolyzed water produced in non-diaphragm all-in-one electrolytic cell was identified to be useable as a cleaner like strong alkaline electrolyzed water produced in diaphragm electrolytic cell. Strong alkaline electrolyzed water produced in non-diaphragm all-in-one electrolytic cell is thought to have sterilizing power because it has active chlorine which is different from strong alkaline electrolyzed water produced in diaphragm electrolytic cell.

• Journal of The Korean Association For Science Education
• /
• v.37 no.4
• /
• pp.719-730
• /
• 2017

The purpose of this study is to investigate how engineering design-based STEM research experience affects gifted students' creative engineering problem-solving propensity and attitude toward engineering. The students' creative engineering problem-solving propensity and attitude toward engineering were measured before and after the STEM research experience. The pre-/post-tests results were analyzed by paired t-test with the significance level of p <.05. The conclusions of the study are as follows: First, the engineering design based STEM research experience had a positive effect on the students' creative engineering problem-solving propensity. Over all, the average score of the creative engineering problem-solving propensity increased significantly (p <.05) after the STEM research experience. Second, the average score of gifted-students' attitude toward engineering had increased significantly after the integrated STEM research activities (p <.05). In addition, we analyzed the difference between pre-post results of both instruments based on the gifted students' desired career paths (natural science and engineering) and gender. The result shows that the students' career paths or gender did not affect the results in most of the sub-categories in both instruments. However, the STEM research experience had more positive effect on the female students than male students in term of their 'engineering design ability', which is one of the sub-categories of the creative engineering problem-solving propensity instrument.

• Korean Journal of Optics and Photonics
• /
• v.4 no.1
• /
• pp.15-21
• /
• 1993

This paper describes the design and development of a KrF excimer laser stepper and discusses the detailed system parameters and characterization data obtained from the performance test. We have developed a deep UV step-and-repeat system, operating at 248 nm, by retrofitting a commercial modules such as KrF excimer laser, precision wafer stage and fused silica illumination and 5X projection optics of numerical aperture 0.42. What we have developed, to the basic structure, are wafer alignment optics, reticle alignment system, autofocusing/leveling mechanisms and environment chamber. Finally, all these subsystem were integrated under the control of microprocessor-based controllers and computer. The wafer alignment system comprises the OFF-AXIS and the TTL alignment. The OFF-AXIS alignment system was realized with two kinds of optics. One is the magnification system with the image processing technique and the other is He-Ne laser diffraction type system using the alignment grating on the wafer. 'The TTL alignment system employs a dual beam inteferometric method, which takes advantages of higher diffraction efficiency compared with other TTL type alignment systems. As the results, alignment accuracy for OFF-AXIS and TTL alignment system were obtained within 0.1 $\mu\textrm{m}$/ 3 $\sigma$ for the various substrate on the wafers. The wafer focusing and leveling system is modified version of the conventional systems using position sensitive detectors (PSD). This type of detection method showed focusing and leveling accuracies of about $\pm$ 0.1 $\mu\textrm{m}$ and $\pm$ 0.5 arcsec, respectively. From the CD measurement, we obtained 0.4 $\mu\textrm{m}$ resolution features over the full field with routine use, and 0.3 $\mu\textrm{m}$ resolution was attainable under more strict conditions.

• Land and Housing Review
• /
• v.6 no.1
• /
• pp.31-39
• /
• 2015

Most landscape areas in apartment complex have been changing. Increasing the area of underground parking lots have an effect on apartment's circumstance. Natural ground was decreased so that the most space in apartment complex were converted into an artificial ground. To suggest the soil quality management, this study examined the actual situation about the soil quality of planting ground such as the quality standard as artificial soil, the difference of natural ground, and the difference of soil quality according to the work classification. As a result, the soil quality of the apartment complex with a large underground parking lot had low quality of soil. Soil physical properties were relatively fine but soil chemical properties needed the quality control. The soil quality of natural ground and artificial ground was not statistically significant and the soil quality by the work classification also had no statistical significance. Therefore, we established improvements about standards of the chemical properties for quality management, the soil quality in the natural ground and applying the equivalent standard according to the work classification.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.10 no.3
• /
• pp.237-242
• /
• 2016

The major advantage of slip-ring technology in Spiral CT is that it facilitates continuous rotation of the x-ray tube, so that volume data can be acquired from a patient quickly. Not only for such a fast scan, but also for the dose reduction purpose, high signal-to-noise ratio and fast data acquisition system is required. In this study, we have built a multi-channel photodetector and multi-channel data acquisition system for CT application. The detector module consisted of CdWO4 crystal and Si photodiode in 16 channels. For the performance test of the preamplifier stage, both the transimpedance and switched integrator types are optimized for the photodetector modules. Switched integrator showed better noise performance in the limited bandwidth which is suitable for the current CT application. The control sequence for data acquisition and 20 bit ADC is designed with VHDL(Very High Speed Integrated Circuit Hardware Description Language) and implemented on FPGA(Field Programmable Gate Array) chip. Our Si photodiode detector module coupled to CdWO4 crystal showed comparable signal with other commercially available photodiode for CT. Switched integrator type showed higher SNR but narrower bandwidth compared to transimpedance preamplifier. Digital hardware is designed by FPGA, so that the control signal could be redesigned without hardware alteration.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.32 no.2
• /
• pp.163-171
• /
• 2014

Based on the GPS/IMU integration, the car navigation has unstable conditions as well as drastically reduces accuracies in urban region. Nowadays, many cars mounted the camera to record driving states. If the ground coordinates of street furniture are known, the position and attitude of camera can be determined through SPR(Single Photo Resection). Therefore, an estimated position and attitude from SPR can be applied measurements in Kalman filter for updating errors of navigation solutions from GPS/IMU integration. In this study, the GPS/IMU/SPR integration algorithm was developed in loosely coupled modes through extended Kalman filters. Also, in order to analyze performances of GPS/IMU/SPR, simulation tests were conducted in GPS signal reception environments and the GCPs (Ground Control Points) distributions. In fact, the position and attitude gathered from GPS/IMU/SPR integration are more precise than the position and attitude from GPS/IMU integration. When IPs (image points), corresponded to GCPs, were concentrated in the center of image, the position error in the optical axis respectively increased. To understand effects from SPR, we plan to carry additional test on the magnitude of GCP, IP and initial exterior orientation errors.

• Journal of Microbiology and Biotechnology
• /
• v.26 no.6
• /
• pp.1115-1123
• /
• 2016

_L-Asparaginase (E.C. 3.5.1.1) is an enzyme involved in asparagine hydrolysis and has the potential to effect leukemic cells and various other cancer cells. We identified the _L-asparaginase gene (_L-ASPG86) in the genus Mesoflavibacter, which consists of a 1,035 bp open reading frame encoding 344 amino acids. Following phylogenetic analysis, the deduced amino acid sequence of _L-ASPG86 (_L-ASPG86) was grouped as a type I asparaginase with respective homologs in Escherichia coli and Yersinia pseudotuberculosis. The _L-ASPG86 gene was cloned into the pET-16b vector to express the respective protein in E. coli BL21 (DE3) cells. Recombinant _L-asparaginase (r-_L-ASPG86) showed optimum conditions at 37-40℃, pH 9. Moreover, r-_L-ASPG86 did not exhibit glutaminase activity. In the metal ions test, its enzymatic activity was highly improved upon addition of 5 mM manganese (3.97-fold) and magnesium (3.35-fold) compared with the untreated control. The specific activity of r-_L-ASPG86 was 687.1 units/mg under optimum conditions (37℃, pH 9, and 5 mM MnSO₄).

• Journal of radiological science and technology
• /
• v.33 no.4
• /
• pp.387-394
• /
• 2010

In the field of healthcare, the conventional sterilization treatments have been replaced by irradiation methods which are in accordance with internationally well established quality standards. The quality control in radiation sterilization assures that the absorbed dose of the irradiated material is in agreement with its requirements and standards. The electron beam irradiation requires technical assessments of more process parameters than gamma irradiation does. Korea has witnessed wide uses of electron accelerators since early 2000 but there hasn't been research experiences relating to quality system in accordance with international standards. The new large scale e-beam irradiation system with the specification of 10 MeV, 8 kW was installed and operated in 2008 by Seoul Radiology Services Co. It consists of the electron accelerator, product handling system, safety, documentation and control subsystems into an integrated system to meet the requirement of the Good Manufacturing Practice such as process quality assurance and management of product tracking records. To implement the international standard such as EN ISO11137, it is necessary to understand the purposes aimed in the standard and carry out the tests following the procedures required. This study presented the specification of the e-beam facility and showed what its design requirements and features are. The test results on a variety of process parameters were presented and validated it they are within the required limits.

• Journal of Internet Computing and Services
• /
• v.15 no.2
• /
• pp.95-107
• /
• 2014

This study was conducted to empirically examine the impact of fit between project radicalness and innovativeness of the supply chain on the degree of supply chain integration. In order to test the research hypotheses, a survey was employed. The results show that the degree of supply chain integration varies on the fit between project radicalness and innovativeness of the supply chain. Specifically, when a supply chain consists of two morphogenetic organizations and the supply chain integration project is radical, we see very highly integrated supply chain. We also find high-level integration of supply chain when project is radical even though both a morphogenetic and a homeostatic organization compose a supply chain. However, we find opposite result, which is low integration, if a project is incremental rather than radical and a supply chain is composed of same types of the organizations mentioned above. Interestingly, degree of integration seems to be always low when a supply chain is composed of two homeostatic organizations, regardless of project radicalness. With these findings, this study concludes that a project whose radicalness is match with the supply chain's innovativeness should be chosen for successful supply chain integration.

• Journal of the Korean Society for Library and Information Science
• /
• v.49 no.3
• /
• pp.109-133
• /
• 2015

The purpose of this study is to develop a model of the TOC (Table of Contents)-based research record system and to comparatively analyze its usability, in order to comprehensively and systematically manage and practically use the various research records generated from the entire process of research and development. For this purpose, the templates for technical recording and the components of each item were proposed to enable technical recording based on TOC, and structured contents were designed to organically connect between these TOC technical records and existing research records. Also, a database logical schema was developed to design a database, and a test collection was constructed on the basis of research records and TOC technical records. Finally, the model of research record system was constructed by designing TOC record search system and user interface including integrated search system. Based on this model, the usability assessment was performed by comparing the existing distributed general systems with the TOC-based research record system. As a result of the comparative analysis of these two systems, the TOC-based research record system showed generally higher utilization of research records than the general systems.