• Safety and Health at Work
• /
• 제13권3호
• /
• pp.357-363
• /
• 2022

Background: Refractory ceramic fibers (RCFs) are a suspected carcinogen but have been widely used as insulations. Depending on the temperature, RCFs can transform into crystalline SiO₂, which is a carcinogen that can be present in the air during bulk RCF handling. This study analyzed the physicochemical and morphological characteristics of RCFs at high temperatures and determined the exposure levels during the semiconductor scrubber maintenance. Methods: Sampling was conducted at a company that manufactures semiconductor scrubbers using RCFs as insulation. Bulk RCF samples were collected both before and after exposure to a scrubber temperature of 700℃. Airborne RCFs were collected during scrubber maintenance, and their characteristics were analyzed using microscopes. Results: The components of bulk RCFs were SiO₂ and Al₂O₃, having an amorphous structure. Airborne RCFs were morphologically different from bulk RCFs in size, which could negatively affect maintenance workers' health. 58% of airborne RCFs correspond to the size of thoracic and respirable fibers. RCFs did not crystallize at high temperatures. The exposure caused by airborne RCFs during the scrubber frame assembly and insulation replacement was higher than the occupational exposure limit. Conclusion: Workers conducting insulation replacement are likely exposed to airborne RCFs above safe exposure limits. As RCFs are suspected carcinogens, this exposure should be minimized through prevention and precautionary procedures.

• 한국화재소방학회논문지
• /
• 제29권4호
• /
• pp.49-56
• /
• 2015

본 연구에서는 건물 실내에서 주로 사용되고 있는 합판, 실내 마감용 목재(루바; 소나무), 압축 스티로폼 단열재, 강화마루 및 PVC 장판 5 종류의 연소가스 유해성을 분석하였다. 연소가스의 유해성 분석은 Naval Engineering Standard(NES) 713 규격 및 미국국방성 규격(MIL-DTL)을 적용하였다. $CO_2$의 방출량은 5종의 내장재 모두 NES 713 규격 한계치인 100,000 ppm을 초과하지 않았다. CO 방출량의 경우 압축 스티로폼 단열재가 6,098 ppm으로 규격 한계치인 4,000 ppm을 초과하는 값을 나타내었다. 포름알데히드는 PVC 장판과 압축 스티로폼 단열재에서 각각 25 ppm, 49 ppm 방출되었다. $NO_X$는 합판에서 955 ppm으로 가장 높은 양이 방출되었으며, 규정 한계치 250 ppm에 비하여 높은 값으로 나타났다. 독성 지수는 합판 5.19, PVC 장판 4.13, 압축 스티로폼 단열재가 2.35, 강화마루 2.34, 그리고 실내 마감용 목재 1.22로 산출되었다. 본 연구에서는 화재 시 발생되는 연소가스 측정 및 유해가스 농도를 확인하여, 향후 건축 내장재의 화재 안전성을 평가하기 위한 기초 데이터로 활용하고자 한다.

• 에너지공학
• /
• 제27권2호
• /
• pp.1-13
• /
• 2018

미세먼지 저감 및 에너지원 변환에 대한 정책 추진에 따라 천연가스를 연료로 하는 발전의 비중이 확대되고 있다. 복합화력발전 플랜트, 열병합발전 플랜트 등에서 천연가스 연료공급계통이 가스가 가열된 상태에서 고압으로 운용되고 있으므로, 누출사고를 예방하여 화재 및 폭발에 의해 사고를 방지하여야 한다. 본 연구에서는 API RP 581 RBI 코드를 기반으로 복합화력발전 플랜트의 천연가스 연료공급계통을 대상으로 위험도 평가를 수행하였다. API RBI 코드의 적용을 위해 평가 대상 계통의 라인 및 세그먼트를 구분하였다. 파손확률과 파손피해 산출을 위해 운전 데이터 및 입력 정보를 분석하였다. 설치 초기 시점 및 운전시간 경과에 따른 위험도 평가 결과 추이를 분석하였다. 코드 기반 평가 시 가스연료 공급계통은 두께 감육, 외부 손상, 기계적 피로 손상기구의 영향이 주로 반영되었다. 운전 시간이 경과함에 따라 단열재 하부 부식(CUI, Corrosion Under Insulation) 등에 의한 외부손상이 위험도를 상승시키는 원인으로 예상되었다.

• 한국안전학회지
• /
• 제29권6호
• /
• pp.137-143
• /
• 2014

Asbestos is given to a variety of six naturally occurring silicate minerals. These minerals possess high tensile strength, flexibility, resistance to chemical and thermal degradation, and electrical resistance. These minerals have been used for decades in thousands of commercial products, such as insulation and fireproofing materials, automotive brakes, textile products, cement and wallboard materials. When handled, asbestos can separate into microscopic-size particles that remain in the air and are easily inhaled. It is now known that prolonged inhalation of asbestos fibers can cause serious and fatal illnesses including malignant lung cancer, mesothelioma, and asbestosis. Therefore the use of asbestos and asbestos products has dramatically decreased in recent years. Also all constructions including asbestos should be removed under strictly controlled conditions and very tightly implemented health & safety management systems. In this study, the process of the removal work of the asbestos cement slate was analyzed by IDEF-0 modeling and evaluated by 4M risk assessment method. The results show that removal work of the asbestos cement slate was classified five process and eighteen detail process. The risk of safety side the higher than the risk of health side in 4M risk assessment.

• 한국안전학회지
• /
• 제19권4호
• /
• pp.36-41
• /
• 2004

This paper presents an qualitative assessment for hazard on the electric power installations of a construction field using FMEL The power installations have the mission to maintain the highest level of service reliability on the works. The more capital the electric power invest the higher service reliability they plausibly will achieve. However, because of limited resources, how effectively budgets can be allocated to achieve service reliability as high as possible. The assessment typically generates recommendations for increasing component reliability, thus improving the power installation safety. The FMEA tabulates the failure modes of components and how their failure affects the power installations being considered. Tn order to estimate the risks of a failures, the FMEA presents criticality estimation or risk priority number using the severity, occurrence, and detectability. The results showed that the highest components of the risk priority number among components were condenser, transformer, MCCB and LA. And In case of the criticality estimation, the potential failure modes were abnormal temperature rise, insulation oil leakage, deterioration for the transformer, overcurrent for the MCCB and operation outage fir the LA.

• 조명전기설비학회논문지
• /
• 제17권2호
• /
• pp.66-72
• /
• 2003

본 연구에서는 국내 배전계통에 사용 중인 전력케이블에 대한 평균열화평가시스템을 개발하였다. 절연진단의 최소한의 목적은 전력공급의 중단을 초래할 수 있는 열화 즉, 사고가능성이 논은 전력케이블을 효율적으로 선별하고 경제적으로 관리하는데 있다. 따라서 이러한 최소한의 진단 목표를 달성하기 위한 가장 효율적인 진단원리로 열화시정수법을 채택하고 감쇠전압을 측정변수로 하여 진단설비를 개발하였다. 현장적용성 시험 및 파괴강도 시험 결과 열화상태 평가결과와 파괴강도의 상관관계를 확인하였으며 본 연구를 통해 개발된 진단장치는 사고를 초래할 수 있는 열화의 효율적이고 경제적인 선별 및 관리에 유용한 설비가 될 수 있음을 알았다.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2004년도 춘계학술대회 논문집
• /
• pp.546-549
• /
• 2004

This paper describes the electrical characteristics of the polymer lightning arresters(L.As) used to protect distribution lines and power facilities from surge. For the relative comparison, the characteristics assessment was done for 2 states of L.As before and after water immersion treatment. The L.As for the comparative test were immersed with water of $95[^{\circ}C]$ considered a severe condition. After the immersion treatment, the assessment was carried out for material analyses in chemical structure(FTIR : fourier transform infrared spectrophotometer). Electrical performance measured insulation resistance measurement, leakage current measurement, critical operation voltage measurement etc.. In addition to, the results were compared with those for the L.As deteriorated in the field. Thus, the accelerative deterioration degree of polymer materials by immersion treatment was evaluated, by which the structural defects of the polymer L.As could be inferred.

• Journal of Electrical Engineering and Technology
• /
• 제10권1호
• /
• pp.344-354
• /
• 2015

In order to study the development of partial discharge (PD) under typical protrusion defects in gas-insulated switchgear, we applied step voltages on the defect and obtained the ${\varphi}-u$ and ${\varphi}-n$ spectrograms of ultra-high frequency (UHF) PD signals in various PD stages. Furthermore, we extracted seven kinds of features to characterize the degree of deterioration of insulation and analyzed their values, variation trends, and change rates. These characteristics were inconsistent with the development of PD. Hence, the differences of these features could describe the severity of PD. In addition, these characteristics could provide integrated characteristics regarding PD development and improve the reliability of PD severity assessment because these characteristics were extracted from different angles. To explain the variation laws of these seven kinds of parameters, we analyzed the relevant physical mechanism by considering the microphysical process of PD formation and development as well as the distortion effect generated by the space charges on the initial field. The relevant physical mechanism effectively allocated PD severity among these features for assessment, and the effectiveness and reliability of using these features to assess PD severity were proved by testing a large number of PD samples.

• Transactions on Electrical and Electronic Materials
• /
• 제13권5호
• /
• pp.229-232
• /
• 2012

DGA is one of the most recent techniques developed to diagnose the fault condition on oil filled insulation transformers. There are more than 6 known different methods of DGA fault interpretation technique and so there is the likelihood that they may vary in their interpretations. A series of combined interpretation methods that can determine the power transformer condition faults in one assessment is therefore needed. This paper presents a computer program- based system developed to combine four DGA assessment techniques; Rogers Ratio Method, IEC Basic Ratio Method, Duval Triangle method and Key Gas Method. An easy to use Graphic User Interface was designed to give a visual display of the four techniques. The result shows that this assessment method can increase the accuracy of DGA methods by up to 20% and the no prediction result had been reduced down to 0%.

• 한국생활과학회지
• /
• 제7권1호
• /
• pp.119-127
• /
• 1998

The purpose of this study was to evaluate thermal properties of pesticide protective clothing made of three different nonwoven fabrics which have barrier properties of pesticide. In order to assay the thermal properties of experimental clothing, thermal resistance measurements for clo value and thermographic assessment were conducted using a surface temperature controlled thermal manikin. The thermal manikin was dressed with underwear and experimental clothing. Air temperature in a climate chamber was kept at $28^{\circ}C$ and its humidity was 70% RH. Air velocity was controlled at less than 0.15m/s. Inner radient temperature was almost equal to the air temperature. The basic thermal insulation value(Icl) of underwear was 0.28 clo. The thermal properties of the experimental clothing were varied according to the type of material used in construction. The basic clothing insulation value for C1(spunbonded nonwoven fabric), C2(spunlaced nonwoven fabric), C3(SMS nonwoven fabric) were 0.705 clo, 0.725 clo, 0.738 clo respectively. The C3 experimental clothing made of SMS resulted in higher surface temperatures than the others with more yellowing spots being evident on the thermogram.