• 제어로봇시스템학회논문지
• /
• 제3권3호
• /
• pp.280-288
• /
• 1997

In this paper, we will show that the torque ripple in closed-loop drives of permanent magnet stepping motors is reduced as properly selected lead angle control method. We propose an instantaneous torque equation, which is the function of lead angle, to estimate the influence on torque ripple. We design a closed-loop lead angle control system based on the proposed instantaneous torque equation and measure the instantaneous torque in various excitation modes. It is shown that torque ripple is greatly reduced, as seen from the experimental results as well as from the computer simulation results. For example, torque ripple reduced from 78.25% to 46.82% in the case of 50 PPS single-phase excitation mode operation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.87-90
• /
• 2006

The direct instantaneous torque control (DITC) method is presented in this paper, which enables torque to be generated during all region and instantaneous torque control to be possible. The hysteresis control mode with the compared value between given torque and instantaneous output torque as input is applied in respect region. The output torque function, that is instantaneous output torque with the variation of current and position of rotor, is achieved by experiment. In this control mode the torque subsection function and current control are not needed. The turn on angle with variation of load torque and speed is only selected and turn off angle can be neglected. The validity of method is tested by simulation and experiment.

• 전기학회논문지
• /
• 제56권6호
• /
• pp.1047-1054
• /
• 2007

This paper presents a high efficiency direct instantaneous torque control (DITC) of Switched Reluctance Motor(SRM) based on the nonlinear model. The DITC method can reduce the high inherent torque ripple of SRM drive system, but drive efficiency is somewhat low due to the high current and switching loss during commutations. In order to reduce a torque ripple, a fast torque reference trajectory is selected at every instantaneous rotor position. Based on the nonlinear model of SRM, the developing torque by one phase is fixed and the other phase is regulated for minimum switchings of phase switch and variation of torque. The switching during commutation can be reduced and fast commutation can be obtained in the proposed method. As a result, drive efficiency could be improved as well as torque ripple reduction. The validity of proposed method is verified by computer simulations and comparative experiments.

• 전기학회논문지
• /
• 제56권10호
• /
• pp.1751-1756
• /
• 2007

This paper presents a high performance pressure control scheme for SR(Switched Reluctance) type hydraulic oil pump using DITC(Direct Instantaneous Torque Control). SR drive has a good feature for pump applications due to a high efficiency, high speed and high torque characteristics. But, SR drive has high torque ripple in commutation region. So, the pump pressure variation is high in the region. In order to reduce the pressure variation, DITC combined with pressure control scheme is presented in this paper. A simple PI controller with flow and pressure limit, generates a reference torque to keep the constant actual pump pressure. The direct torque controller of SR drive generates inverter switching signals according to a control rule and a torque estimator. Computer simulation and experiemtal results show the validation of the proposed control scheme.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1997년도 전력전자학술대회 논문집
• /
• pp.454-459
• /
• 1997

The good features of a switched reluctance motor(SRM) are appreciated by the appliance manufactures. And it is spread into a commercial and industries market. The few disadvantage of the motor is higher torque ripple and noise. This paper proposes an instantaneous torque control scheme to control a speed precisely. It adapts phase-locked loop (PLL) technique to control speed precisely. In this control scheme, the phase detector signal of the PLL regulates the switching dwell angle flexibly and the loop filter's signal controls adaptively the instantaneous switching voltage. Experimental results show that drive performance is good with low torque ripple.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.231-233
• /
• 2001

This paper describes an analytical solution of the voltage commands for instantaneous torque control of an I.M. The analytical solution is expressed as a simple explicit function of the instantaneous torque commands and motor speed. On the basis of the derived analytical solution, the maximum torque change rate of an I.M with a limited voltage-source is analyzed, and also the dynamic influence of rapid changes in motor speed on output torque derivations is investigated. The detailed results of these two analyses are approximated here in term of first-order linear differential equations, and their validities are confirmed through the demonstrative numerical simulations. This paper includes the simulation results of the instantaneous torque control with varied motor parameters for sensitivity analysis.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.148-149
• /
• 2007

In this paper, an advanced torque control scheme of SRM using DITC(Direct Instantaneous Torque Control) and PWM(pulse width modulation) is investigated. The proposed DITC-PWM regulates a duty ratio of the phase switch according to the torque error and simple control rules of DITC without any hysteresis bandwidth. The proposed control method is verified by the simulations and experimental results.

• 드라이브 ㆍ 컨트롤
• /
• 제17권2호
• /
• pp.28-37
• /
• 2020

It is difficult to analytically derive the relationship among volumetric displacement, flowrate, torque, and rotation speed regarding an instantaneous position of gerotor hydraulic pumps/motors. This can be explained by the geometric shape of the rotors, which is highly complicated. Herein, an analytical method for the instantaneous torque, rotation speed, flowrate, and volumetric displacement of a pump/motor is proposed. The method is based on two physical concepts: energy conservation and torque equilibrium. The instantaneous torque of a pump/motor shaft is determined for the posture of rotors from the torque equilibrium. If the torque equilibrium is combined with the energy conservation between the hydraulic energy of the pump/motor and the mechanical input/output energy, the formula for determining the instantaneous volumetric displacement and flowrate is derived. The numerical values of the instantaneous volumetric displacement, torque, rotation speed, and flowrate are calculated via the MATLAB software programs, and they are illustrated for the case in which inner and outer rotors rotate with respect to fixed axes. The degrees of torque fluctuation, speed fluctuation, and flowrate fluctuation can be observed from their instantaneous values. The proposed formula may provide a better understanding of the design or analysis process of gerotor pumps/motors.

• 전력전자학회논문지
• /
• 제13권3호
• /
• pp.179-185
• /
• 2008

본 논문에서는 SRM의 토크리플 억제를 위하여 PWM(Pulse width modulation)과 직접토크제어(DITC, Direct Instantaneous Torque Control) 방식의 결합에 의한 제어방식을 제안하였다. 기존의 직접토크제어와 달리, 제안된 방식은 한 샘플링 구간 내에서 하나 또는 두 개의 스위칭 모드로 동작하며, 스위칭 패턴의 폭은 토크 오차와 직접 토크제어 방식의 제어규칙에 따라 제어된다. 또한 실제 스위치의 제어폭이 토크 오차에 따라 가변적으로 제어됨으로써, 같은 샘플링 주기에서 기존의 직접토크제어 방식에 비하여 토크리플을 크게 억제할 수 있으며, 토크 연산의 샘플링 주기를 크게 할 수도 있는 장점이 있다. 간단한 제어규칙과 PWM 듀티비의 계산으로 복잡한 연산이 요구되지 않으므로 저가의 마이크로 프로세서에 의해 구현이 가능하다. 제안된 방식은 컴퓨터 시뮬레이션과 실험을 통하여 검증하였다.

• 전기학회논문지P
• /
• 제52권1호
• /
• pp.1-8
• /
• 2003

The paper proposes instantaneous torque control of IPMSM for maximum torque drive of torque and current plane. The control scheme is based on the mathematical model of the motor and is applicable to the constant torque and field weakening operations. The scheme allows the motor to be driven with maximum torque per ampere(MTPA) characteristic below base speed and it maintains the maximum voltage limit of the motor wide field weakening and the motor current limit under all conditions of operation accurately. For each control mode, a condition that determines the optimal d-axis current $^id$ for maximum torque operation is derived. The proposed control algorithm is applied to IPMSM drive system for drive of wide speed range, the operating characteristics controlled that maximum torque control are examined in detail by simulation.