• 대한원격탐사학회지
• /
• 제19권5호
• /
• pp.341-349
• /
• 2003

The so-called B-method, a simplified surface energy budget, permits calculation of daily actual evapotranspiration (ET) using remotely sensed data, such as NOAA-AVHRR. Even if the use of satellite data allows estimation of the albedo and surface temperature, this model requires meteorological data measured at ground-level to obtain the other inputs. In addition, a difficulty may be occurred by the difference of temporal scales between the net radiation in daily scale and instantaneous measurement at midday of the surface and air temperatures because the data covered whole day are necessary to obtain accumulated daily net radiation. In order to solve these problems, this study attempted a modification of B-method through an extension of hourly ET value calculated using a complete instantaneous inputs. The estimation of the daily apparent ET from newly proposed system showed a root mean square error of 0.26 mm/day as compared the output obtained from the classical model. It is evident that this may offer more rapid estimation and reduced data volume.

• 한국초전도ㆍ저온공학회논문지
• /
• 제14권1호
• /
• pp.38-43
• /
• 2012

In the extreme conditions of launch vehicle in a space, such as cryogenic temperature and low-gravity environment, the mass gauging of remaining propellants becomes a difficult problem. Pressure-volume-temperature (PVT) method is one of the attractive mass gauging methods under low-gravity due to its simplicity and reliability. PVT gauging experiment with various mass flow rates of helium injection is carried out with the experimental apparatus creating cryogenic homogeneous condition as the condition of low-gravity. Experimental results are analyzed by a novel PVT gauging analysis method which considers all instantaneous changes of pressure and temperature in the ullage volume with small time intervals. It is observed that the gauging error from the novel PVT gauging analysis is -0.11% with 2 slpm mass flow rate of helium injection.

• 설비공학논문집
• /
• 제19권3호
• /
• pp.220-227
• /
• 2007

Heat transfer and momentum transfer under conditions of both oscillating flow and oscillating pressure within pulse tubes show very different behavior from those for steady state conditions. The analytic solutions of axial velocity and temperature of the gas within pulse tubes were obtained by assuming that the variations in pressure and temperature were purely sinusoidal and small. The shear stress and the heat flux at the tube wall obtained from the solutions are expressed in terms of the cross-sectional averaged velocity, the difference between mean temperature and instantaneous cross-sectional averaged temperature and the difference between mean pressure and instantaneous pressure. It is shown that the complex shear factor, which has been applied to momentum transfer of incompressible oscillating flow, and the complex Nusselt number, which has been applied to either heat transfer with oscillating pressure only or heat transfer of incompressible oscillating flow, could also be used for momentum transfer and heat transfer subjected to both oscillating flow and oscillating pressure, respectively.

• Nuclear Engineering and Technology
• /
• 제38권2호
• /
• pp.147-154
• /
• 2006

Thermal fatigue of the coolant circuits of PWR plants is a major issue for nuclear safety. The problem is especially accute in mixing zones, like T-junctions, where large differences in water temperature between the two inlets and high levels of turbulence can lead to large temperature fluctuations at the wall. Until recently, studies on the matter had been tackled at EDF using steady methods: the fluid flow was solved with a CFD code using an averaged turbulence model, which led to the knowledge of the mean temperature and temperature variance at each point of the wall. But, being based on averaged quantities, this method could not reproduce the unsteady and 3D effects of the problem, like phase lag in temperature oscillations between two points, which can generate important stresses. Benefiting from advances in computer power and turbulence modelling, a new methodology is now applied, that allows to take these effects into account. The CFD tool Code_Saturne, developped at EDF, is used to solve the fluid flow using an unsteady L.E.S. approach. It is coupled with the thermal code Syrthes, which propagates the temperature fluctuations into the wall thickness. The instantaneous temperature field inside the wall can then be extracted and used for structure mechanics computations (mainly with EDF thermomechanics tool Code_Aster). The purpose of this paper is to present the application of this methodology to the simulation of a straight T-junction mock-up, similar to the Residual Heat Remover (RHR) junction found in N4 type PWR nuclear plants, and designed to study thermal striping and cracks propagation. The results are generally in good agreement with the measurements; yet, in certain areas of the flow, progress is still needed in L.E.S. modelling and in the treatment of instantaneous heat transfer at the wall.

• 대한기계학회논문집
• /
• 제14권5호
• /
• pp.1234-1243
• /
• 1990

본 연구에서는 선회가 없는 중심기류와 주위기류의 난류 전단층에서 형성되는 난류확산화염의 천이영역(transition region)에 주목하여 전단층내의 혼합작용과 화염 구조와의 상호작용을 규명하기 위해 거시적 및 순간적인 화염구조에 대해 실험적으로 조사 연구한 결과를 보고한다.

• 설비공학논문집
• /
• 제10권5호
• /
• pp.619-629
• /
• 1998

An experimental work was conducted to investigate a feasibility of simultaneous measurement of gas-liquid two-phase flowrates with double orifice plates using air and water. The tests were carried out under the atmospheric pressure and at the ambient temperature using two different tube sizes. Qualities of an air-water flow in the present study have values less than 0.1 and thus the mixed flow showed bubbly, plug, slug flow regimes. The probability density function (PDF) and the power spectral density function (PSDF) of the instantaneous pressure drop traces for the flow regimes were obtained. It is found that some distinctive features exist in the distribution of these functions, depending upon the two-phase flow pattern. The time-averaged value of the instantaneous pressure drop increases with increasing gas and liquid flowrates, showing a single-valued function for the total mass flowrate and the quality. It is also found that the two-phase discharge coefficient exhibits a consistent trend for variation of dimensionless parameters such as the superficial velocity ratio and the gas Reynolds number. The results indicate that simultaneous measurement of two-phase flowrate may be possible based upon a statistical analysis of the instantaneous pressure drop curves monitored using double orifice plates.

• 대한기계학회논문집
• /
• 제16권7호
• /
• pp.1398-1407
• /
• 1992

본 연구에서는 정적연소기를 대상으로 하여 화염전파중의 열손실을 연소실내 의 압력 및 슐리렌 촬영한 화염사진에 의해 구한 발생열로부터 추정하는 방법을 제시 하고, 연소실 벽면의 순간온도를 직접 측정함으로써 상기방법에 의한 열손실 추정법의 타당성을 입증하였다. 그리고 이 열손실과 기연가스가 연소실 벽면에 접하는 열전달 면적과의 관계를 해석하므로서, 추후 열손실을 고려한 연소실 형상 설계에 있어서의 기초자료를 제시하고자 하였다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.776-780
• /
• 2002

This paper describes the concept and the characteristics of hyper interfacial bonding developed as a new concept joining process for UFG (ultra-fine grained) steel. Hyper interfacial bonding process is characterized by instantaneous surface melting bonding which involves a series of steps, namely, surface heating by high frequency induction, the rapid removing of heating coil and joining by pressing specimens. UFG steels used in this study have the average grain size of 1.25 ${\mu}{\textrm}{m}$. The surface of specimen can be rapidly heated up and melted within 0.2s. Temperature gradient near heated surface is relatively steep, and peak temperature drastically fell down to about 1100K at the depth of 2~3mm away from the heated surface of specimen. Bainite is observed near bond interface, and also M-A (martensite-austenite) islands are observed in HAZ. Grain size increases with increasing heating power, however, the grain size in bonded zone can be restrained under 11 ${\mu}{\textrm}{m}$. Hardened zone is limited to near bond interface, and the maximum hardness is Hv350~Hv390.

• 대한기계학회논문집B
• /
• 제25권5호
• /
• pp.611-618
• /
• 2001

The flow characteristics of a turbulent buoyant jet were experimentally investigated using a single-frame PIV system. The Reynolds number based on the nozzle exit velocity and nozzle diameter was about Re=5$\times$10$^3$. The instantaneous velocity fields in the streamwise plane passing the jet axis were measured in the near field X/D <11 with and without the temperature gradient. By ensemble averaging the instantaneous velocity fields, the spatial distributions of mean velocity, vorticity, and higher-order statistics up to third order were obtained. The temperature difference of 10$\^{C}$ does not affect a significant influence to the flow structure in the near field, but the total entrainment rate is increased slightly. The entrainment rate shows a linear variation with the streamwise distance in the region after X/D=5.0.

• 한국화재소방학회논문지
• /
• 제30권1호
• /
• pp.24-30
• /
• 2016

자연발화 특성은 가연성물질의 취급 및 화재예방을 위한 중요한 인자이다. 본 연구는 ASTM D2155식 발화온도 측정장치를 사용하여 Ethylene Glycol과 물을 혼합한 시료의 자연발화 특성을 고찰하였다. Ethylene Glycol 100%는 시료량 $75{\mu}l{\sim}160{\mu}l$의 범위에서 $434^{\circ}C$로 나타났다. 물을 첨가하여 Ethylene Glycol 80%와 물 20%를 혼합한 시료는 시료량 $100{\mu}l{\sim}125{\mu}l$의 범위에서 $434^{\circ}C$로 나타났고, Ethylene Glycol 60%와 물 40%를 혼합한 시료에서 시료량 $120{\mu}l{\sim}160{\mu}l$의 범위에서 $437^{\circ}C$로 나타났다. 또한 순간발화온도는 시료량 $125{\mu}l$에서 각각 $579^{\circ}C$, $595^{\circ}C$ 및 $611^{\circ}C$를 구하였으며, 물의 비율이 증가할수록 자연발화온도와 순간발화온도는 증가되는 것으로 나타났다.