• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.2
• /
• pp.143-150
• /
• 2000

In this paper, an optimum size for the inset cut feed of microstrip antennas has been determined by using the finite-difference time domain method. At first, the return losses of microstrip antennas having various shapes and types of the inset cut feeds have been computed numerically for a given frequency and a substrate. Then an optimum size of the inset cut feed has been determined by iterative computation procedure for a given condition. It was found that the optimum width of the inset cut feed is about 0.42 times of the width of 50Ω feed line and the optimum length of the inset cut feed is about 0.36 times of the length of the antenna patch. These results are proved by the experimental data obtained from the measurements of many fabricated antennas. It was also found that the optimum size of the inset cut feed is independent on the frequency, the height and the dielectric constant of the antennal substrate.

• Journal of information and communication convergence engineering
• /
• v.10 no.2
• /
• pp.123-128
• /
• 2012

In communication systems, there are various types of microstrip antenna that can be used for many applications. This paper mainly focuses on the simple design of an inset rectangular microstrip patch antenna to operate at a frequency of 2.45 GHz for rectenna design. The study involves using an high frequency structure simulator to design the antenna dimensions and to determine its performance. This antenna is based on a thickness of 1.6 mm flame retardant 4 (FR-4) substrate having a dielectric constant of approximately 4.7, an inset feed, and a ground plane. After simulation, the antenna performance characteristics such as its return loss, voltage standing wave ratio, gain, and radiation pattern were obtained and compared with the fabricated measured antenna.

• Journal of IKEEE
• /
• v.27 no.4
• /
• pp.405-410
• /
• 2023

This paper presents a novel method of implementing a dual-band antenna using a square patch with an inset feed structure. The proposed method is to simply design a dual-band antenna using an asymmetric inset structure with different lengths of slots dug into the patch for inset feeding. To verify the proposed method, a dual-band inset patch antenna supporting 1.57 GHz GPS and 2.4 GHz WiFi bands was designed and manufactured on a 1 mm thick FR4 substrate. From measurement, it was confirmed that the frequency bands of the antenna that satisfy a return loss of -10dB or less are 1.55~1.57GHz and 2.41~2.45GHz, which has dual-band characteristics. Using the proposed method, it is possible to simply implement a dual-band antenna using inset feeding, and it is expected to be utilized in a variety of application fields.

• Journal of Satellite, Information and Communications
• /
• v.10 no.2
• /
• pp.80-85
• /
• 2015

In this paper, we present, an indstrial RFID layered microstrip patch antenna is designed using an inset feed method in order to improve recognition rates in a long distance as tags are attached to metal object by improving a problem of feeding power in fabricating metal tags and reducing effects of metallic object. The inset feed shows a distinctive characteristic that has no separation between emitters and feed lines differing from a structure with the conventional inductive coupling feed. This structure makes possible to produce a type that presents a low antenna height and enables impedance coupling for tag chips. Although it shows a difficulty in the impedance coupling due to increases in the parasite capacitance between a ground plane and an emitter in an antenna according to decreases in the height of a tag antenna, it may become a merit in designing the tag antenna because the antenna impedance can be determined as an inductive manner if a shorted structure is used for feeding power. Therefore, in this paper the microstrip patch antenna is designed as a modified type and applies the inset feed in order to reduce effects of metallic objects where the antenna is be attached. Also, the antenna uses a multi-layer structure that includes a metal plate between radiator and ground instead of using a single layer.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.5
• /
• pp.33-39
• /
• 2021

In this study, we tried to find the correlation of the parameters and dual resonance of U-slot microstrip patch antenna with L-shaped Inset-feed structure and design broadband antenna using them. In the first step, we classified cases where dual resonance occurs through changes in antenna parameters that affect antenna performance. In the second step, we correlated each antenna parameter to the location and intensity of the resonance point, and 3 dB bandwidth. Next, antenna simulation confirmed the process of designing to have wide bandwidth using the correlation in the second step previously presented in the U-slot antenna case with narrow bandwidth. Finally, we fabricated a designed antenna and demonstrated the validity of antenna bandwidth broadening through the correlation analysis.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.2
• /
• pp.73-78
• /
• 2021

To minimize the resonance frequency error when design Inset-Fed Microstrip Patch Antenna using current formulas. Especially It is found that a constant relation between Antenna patch width and frequency error. Using this relation, calculation frequency and simulation frequency are compared. Finally the comparison induced a formula of revised antenna patch width for accurate frequency in 2-10 GHz. And this formula reduced 2.54% of average frequency error. Last, the Antenna which has same variation with the simulation was producted and measured. It proved the formula's validity.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.3
• /
• pp.461-466
• /
• 2019

In this paper, we have studied the improvement of gain and bandwidth characteristics by using double feeding and L-shaped inset feed line matching circuit in microstrip stacked patch antenna which is widely used to broaden the gain of general microstrip antenna. The proposed structure is composed of two feeding edges of the main patch antenna, each of them are connected to a feeding line having an L shaped inset feeder. And the parasitic patch is placed at a proper distance above the main patch. The size of the main patch is designed so that the resonance frequency is close to the center frequency of the target frequency band. The experimental results show that the bandwidth was increased more than 180MHz in the 2.3-2.7 GHz band, which is more interesting than the single feed, and the gain improvement of 2.5dBi was obtained at 2.7GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.9
• /
• pp.1050-1055
• /
• 2010

In this paper, the K band $3{\times}6$ array antenna having unequal input is presented. To control the input impedance of the patch antenna, the length of inset feed is adjusted. Also, the same current in each element is excited by Kirchhoff's law. The proposed unequal impedance array antenna is a nonuniform amplitude array. The bandwidth of the proposed unequal impedance array antenna is wider by 1.5 times than that of the equal array antenna. This broad bandwidth is thought to be due to multiple resonances of patches. The unequal impedance array antennas have fractional bandwidths of 5.07 % and gains of 18.32 dBi.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.4
• /
• pp.167-171
• /
• 2011

In this paper, $2{\times}4$ microstrip patch antenna are proposed to implement K-band satellite communications. The microstrip feed line are inset into the radiation patch to match input impedance. Also the same current in each elements are excited by Kirchhoff's low. The elements distance of proposed array antenna are optimized $0.8{\lambda}_g$ to minimize a mutual coupling and maximize a gain. A power divider network are employed to distribute T-junction divider. As result, the proposed antenna get gain of 14[dBi] at 10.525[GHz].

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.2
• /
• pp.249-254
• /
• 2014

We have studied on the possibility of railway stability system using RFID tag. UHF RFID tag was desinged, manufactured and tested. Proposed UHF tag antenna has PIFA type structure and inset feed multi matching technique was attempted for impedance matching of antenna. The impedance bandwidth (VSWR < 3) of the proposed tag antenna covers 917~923 MHz. Measured peak gain is 3.225 dBi and UHF band with an omni-directional radiation pattern. RFID reader and tag installed in motor car and track, respectively. Then, tag recognition rate according to velocity of car (under 45 km/h) represented 100 %.