• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.188-192
• /
• 2003

A multilayer two-stage LC bandpass filter using low-temperature cofired-ceramic (LTCC) is proposed in this paper. The proposed bandpass filter is composed of two ceramic substrates with different dielectric constant instead of single ceramic material from top to bottom layer. The bandpass filter size is $2.0 mm{\times}1.2 mm{\times}0.8 mm$. Positioning of attenuation polefrequency, importance parameter for a performance of filter, is discussed using even-odd mode analysis by tuned capacitance of coupling capacitor and those results is implemented to LTCC filter circuit. Measured filter performances show that the insertion losses are -4.5dB, -4.1dB at 2.45GHz, 2.75GHz and the return losses are -8.5dB, 8.7dB.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.1
• /
• pp.65-72
• /
• 2011

In this paper, the T-shape stepped impedance resonators are adopted for the design of microstrip bandpass filters for wide harmonics suppression. The proposed filters are operated at the center frequency of 2.44 GHz and 5.20 GHz, respectively. These bandpass filters have been also applied for a high performance diplexer. The insertion losses at the center frequencies of 2.44 and 5.20 GHz are 1.23 and 1.18, respectively. The applicable return losses for both frequency bands and a wide stopband better than 17 dB up to 20 GHz have been obtained.

• Journal of Astronomy and Space Sciences
• /
• v.30 no.4
• /
• pp.345-353
• /
• 2013

A W-band Orthomode Transducer (OMT) has been developed for Korean VLBI Network (KVN) polarization observation. The OMT design was based on E-plane split-block technique using septum structure. 3-dimensional electromagnetic simulation was fully employed to optimize the performance of the OMT. Measurements of the fabricated OMT show that the return losses for the vertically and horizontally polarized modes are better than -20 dB across 80 ~ 108 GHz and the insertion losses for the both modes are less than 0.47 dB. The cross-polarization level of the OMT is less than -30 dB. The bandwidth of the developed OMT is estimated as around 30%.

• Bulletin of the Korean Space Science Society
• /
• 2008.10a
• /
• pp.25.3-26
• /
• 2008

The direct way to the moon is to start from the parking orbit by using impulsive thruster In previous domestic research, the direct way has been studied by using a single impulsive shot. However, when a single impulsive shot occurs to go into a Translunar orbit, gravity losses occur because thruster is not impulsive shot but the finite burns and it causes the gravity losses. To make up for the weak point of a single impulsive shot, this paper divides TLI (Trans Lunar Injection) into several small burns. Therefore, departure loop trajectory and the Translunar trajectory. This method is useful not only to reduce the gravity losses but also to check the condition of satellite. By using this method, this paper demostrates the optimized trajectory from Earth parking orbit to lunar mission orbit which minimizes the fuel, and the SNOPT (Sparse Nonlinear OPTimizer software) is used to find optimal solution. Also, this paper provides lunar mission profile which includes the mission schedule when TLI, LOI (Lunar Orbit Insertion) maneuvers occur, a mount of fuel when thruster is used and other mission parameters.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.533-536
• /
• 2003

YIG(Yttrium Iron Garnet) is one of the most widely used ferrites for microwave telecommunication. It used as a passive devices such as isolators and circulators. In order to reduce the insertion losses of these passive devices, it is very important to reduce magnetic loss of the ferrites. In general, the magnetic losses of ferrites is closely related to the microstructure of the ceramics. In the sintering of YIG, pores are easily trapped in grains and grain boundaries. These pores cause to increase magnetic losses of the sinterted bodies. In this paper, the effect of the $SiO_2$ addition on the microstructure was discussed. Increasing the $SiO_2$ addition, the grain size was reduced, which means that added acts as a grain-growth inhibitor. During the sintering, $SiO_2$ settled down on the grain boundaries, and drag the grain growth. Therefore, there is enough time for pores to move out. The relative density of YIG sintered at $1350^{\circ}C$ with 1 mol% $SiO_2$ addition was 99.6%. $\Delta$H of these samples was under 50 Oe.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2006.10a
• /
• pp.255-267
• /
• 2006

LTCC Technology is very suitable for 60 GHz application $\blacksquare$ LTCC substrate shows low loss at 60 GHz. - low insertion and return losses $\blacksquare$ Microstrip or CBCPW line is sultable for transmission lines at 60 GHz. - low loss (0.1dB/mm) $\blacksquare$ Single ribbbon bonding is adequate for interconnection - simple - low loss (0.1dB/bonding) $\blacksquare$ Characteristics of MMIC module - Gain difference (${\Delta}S21$) : 0.4 dB

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.313-315
• /
• 1999

We present a 64-channel wavelength multiplexing architecture consisting of two 32-channel wavelength muitiplexers. Measured insertion losses of the 32-channel muitiplexers were below 8㏈ with uniformity in loss among channels better than 1㏈. The architecture of an OADM is also presented which employs FBGs. It is shown that the OADM can add or drop up to 12 channels.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.3A
• /
• pp.179-184
• /
• 2003

In this paper, an asymmetric topology of MMIC SPDT switch was proposed to increase the isolation in the receiving path and decrease the insertion loss with higher P1dB in the transmitting path for the ISM band. This SPDT switch was implemented with 0.5㎛ GaAs MESFETs processed by ETRI for the IDEC MPW project. For the receiving path the measured insertion losses were 1.518dB at 3GHz and 1.777dB at 5.75GHz and the isolations were 38.474dB at 3GHz and 29.125dB at 5.75GHz. For the transmitting path the insertion losses were 0.916dB at 3GHz and 1.162dB at 5.75GHz and the isolations were 23.259dB at 3GHz and 16.632dB at 5.75GHz. Compared to the symmetric topology the isolations of the receiving path for the asymmetric one were improved by 15.9dB at 3GHz and 11.9dB at 5.75GHz and its insertion loss was increased by about 0.6dB. In addition, P1dB of 21.5 dBm for the transmitting path was obtained, which is increased by 3.86dB compared to the symmetric one.

• Journal of Advanced Navigation Technology
• /
• v.22 no.6
• /
• pp.642-647
• /
• 2018

In this paper, an unequal power divider based on adjusting electrical length of uniform transmission line is presented. This divider consists of three uniform transmission lines and one isolation resistor and have the different port impedances of input and output. The feature of proposed divider can changed the power dividing ratio to adjust only electrical length of uniform transmission lines. To verify the feasibility of proposed power divider, two divider circuits are designed, one is 1:2 power dividing ratio divider with $60{\Omega}$ uniform transmission line and $40{\Omega}$ input port impedances and $45{\Omega}$ output port impedances, the performance data were measured the insertion losses of 1.7 dB/ 5.0 dB, return losses of more than -30 dB and isolation of more than -35 dB. The other is 1:4 power dividing ratio divider with $40{\Omega}$ uniform transmission line and $50{\Omega}$ input port impedances and $75{\Omega}$ output port impedances, the performance data were measured the insertion losses of 1.3 dB/ 6.8 dB, return losses of more than -12 dB and isolation of more than -19 dB. The measured performance data agreed well with the simulated results.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.4
• /
• pp.185-190
• /
• 2015

In this paper we characterized and designed the waveguide antipodal finline transition at 57-65GHz frequency band in V-band for 5G mobile communication systems. Especially, we proposed the design method of spline taper for finline tapers by means of increasing curvature from linear taper. We could perform optimization more effectively by excluding improper regions for optimal performance from optimization using the method. Return losses and insertion losses of antipodal finline transitions were mainly affected by the taper shape of the finline. The resonances in the structure of the finline transition were the strongest enemies who deteriorate the performance of the transition. And we alleviated the resonances using semicircle shaped patch. The designed antipodal finline transition showed good performance as it showed less than -24.2dB of return loss and -0.24dB of insertion loss in the band(57-65GHz) which we suppose to use.