• 전기학회논문지
• /
• 제56권6호
• /
• pp.1035-1038
• /
• 2007

We designed and manufactured a 1.8T high temperature superconducting(HTS) insert coil for a NMR magnet operated at 4.2 K. Suitable HTS superconductor and HTS coil were carefully designed and developed. We have selected multi-filamentary Bi2223 conductor fabricated by American Superconductor Corporation(AMSC). The selected conductor consists of Bi2223 filaments of 55, silver stabilizer and stainless steel reinforcement tapes. Therefore, it shows good hoop strength as well as compression tolerance. The conductor has a tape cross-section of 0.31mm x 4.8mm. the Bi2223 conductor shows large anisotropy of critical current. The critical current of conductor in magnetic field parallel to the flat surface are much higher than that in magnetic field perpendicular. The HTS coil has an inner diameter of 78 mm, an outer diameter of 127 mm and a coil length of 600 mm. In this paper, the detailed design, fabrication and test results on the HTS insert coil are presented.

• Design & Manufacturing
• /
• 제14권4호
• /
• pp.11-16
• /
• 2020

In this study, forming of carbon composite parts was performed using an injection/compression molding process. An impregnation of matrix is determined by ability of wet and flow rate between the matrix and reinforcement. The flow rate of matrix passing through the reinforcements is a function of permeability of reinforcement, a viscosity of matrix and pressure gradient on molding, and the viscosity of the matrix depends on the mold temperature, molding pressure and shear strain of matrix. Therefore, compression molding experiment was conducted using a heating mold in order to confirm the possibility of matrix impregnation. The impregnation of the matrix through the porosities between the woven yarns was confirmed by the cross-sectional SEM image of compression molded parts. An injection molding process was also performed at a short cycle time, high molding pressure and low mold temperature than those of compression experiment conditions. Deterioration of impregnation on the surface of molded parts were caused by these injection conditions and it could be the reason of decreasing the maximum tensile strength. In order to improve impregnation of matrix on the surface, injection/compression molding and insert-over molding were applied. As a result of applying injection/compression molding and insert-over molding, it was shown that the improvement of impregnation on the surface and the maximum tensile strength was increased about 2.8 times than the virgin matrix.

• 한국환경복원기술학회지
• /
• 제5권3호
• /
• pp.23-30
• /
• 2002

In recently, using of steel reinforcements by reinforcing materials of the reinforced earth, micro-pile and root-pile etc,. is wide-spreading in the stabilizing control of cutting and embankment slopes, but the failure mechanism of reinforced earth as well as the effect of insert angles or types of reinforcement and others are not defined clearly. In this study, therefore heavy-duty direct shear tests were exercised on the reinforced soil and the non-reinforced soil, which was executed for research on the interaction of soil-reinforcement and theirs behavior. The hardness and softness and the standard sands were used for modeling of reinforced soil, the material constants for the computer simulation were estimated from the results of CD-Test. The effects of reinforcing and of friction increasing on the softness, area ratio of reinforcements is equal, were the better than them of the hardness, as well the reinforcing effects of shear strength without regard to the area ratio is much the same at $10^{\circ}$, insert angle of reinforced bar, differ from them of the existing study. Then, the results of numerical analysis showed that the behavior of reinforcements displayed bending resistance and shear resistance at $15^{\circ}$ and $30^{\circ}$, respectively. Also, the state of strain transfer was observed and the behavior of resistance mechanism on reinforcements presented almost the same them of landslides stabilizing pile.

• 터널과지하공간
• /
• 제34권5호
• /
• pp.554-570
• /
• 2024

본 연구에서는 삽입재 주변부 보강이 픽커터의 마모손상에 주는 효과를 파악하기 위한 현장시험을 수행하였다. 현장시험 수행에 앞서 보강 픽커터와 무보강 픽커터에 대한 선형절삭시험을 통해 픽커터의 보강이 커터작용력에 주는 영향을 확인하였고 그 결과를 기반으로 로드헤더의 용량검토를 수행하였다. 커터 작용력 분석 결과, 평균 연직력과 절삭력은 보강여부에 상관없이 유사했으나, 최대 연직력과 절삭력은 보강여부에 따라 표준편차가 크게 나타났다. 토크 검토에서 평균 절삭력을 사용할 경우는 관입깊이 6 mm 이하, 최대절삭력을 사용할 경우는 4 mm 이하가 적합한 것으로 산정되었다. 마모손상 분석에서는 각 픽커터의 사용개수, 삽입재가 유지되는 개수, 편마모 발생 개수, 사용 전과 후의 중량 차이에서 중량 손실을 제외하면 보강된 픽커터가 보강되지 않은 픽커터에 비해 16%에서 최대 28%까지 향상된 성능을 보여주었다. 이와 같은 결과로부터 픽커터의 보강이 픽커터의 내구성 향상에 상당한 영향을 미친다는 것을 확인할 수 있었다. 다만 픽커터의 보강은 무보강에 비해 재료비와 추가 공정에 의해 비용이 높으므로 성능 향상에 의한 효과와 비용문제를 고려하여 선정할 필요가 있다.

• Composites Research
• /
• 제25권4호
• /
• pp.117-125
• /
• 2012

필름 삽입 사출 시편의 휨은 비대칭적인 잔류응력 분포에 기인한다. 비대칭적 잔류응력과 온도 분포는 삽입된 필름 표면의 수직방향으로 지연되는 열 전달에 의해 발생한다. 사출 공정조건 최적화를 통해 필름 삽입 사출 시편의 휨을 억제할 수 없었기 때문에, 필름 삽입 사출 시편의 휨을 최소화하기 위해서 유리 섬유가 강화된 복합재료를 기판으로 사용하였다. 유리 단섬유의 분포를 마이크로 CT 장비를 이용하여 평가하였다. 복합재료로 구성된 기판을 이용한 필름 삽입 사출 시편의 배향 텐서와 휨을 계산하기 위해서는 적절한 마이크로 역학, 이방적 열팽창계수 및 닫힌 어림법 모델이 선택되어야만 한다. 여섯 종류의 마이크로 역학모델, 세 종류의 열 팽창 계수 모델 및 다섯 종류의 닫힌 어림법 모델을 고려한 후, Mori-Tanaka 모델, Rosen and Hashin 모델 및 third orthotropic 닫힌 어림법 모델을 선택하였다. 수치적으로 계산된 섬유 배향 텐서와 휨에 관한 결과들은 실험결과와 잘 일치하였고, 유리 섬유의 보강효과가 필름 삽입 사출 복합 재료 시편의 휨에 미치는 영향을 파악하였다.

• 한국환경복원기술학회지
• /
• 제5권4호
• /
• pp.19-30
• /
• 2002

The stability of slope using root-pile like to the reinforcements is affected by the interaction behavior mechanism of soil-reinforcements. Through the studying on the interaction in joint of its, therefore, the control roles can be find out in installed slope. In study, the stress level ratio based on the insert angle of installed reinforcements in soil used to numerical analysis, which was results from the duty direct shear test in Lab. The maximum shear strain variation on the reinforcements was observed at insert angle, which was approximately similar to the calculated angle based on the equation proposed by the Jewell. The elasto-plastic joint model on the contact area of soil-reinforcements was presumed, the reinforced soil assumed non-linear elastic model and the reinforcements supposed elastic model, respectively. The finite element analysis of assumed models was performed. The shear strain variation of non-reinforced state obtained by the FEM analysis including elasto-plastic joint elements were shown the rationality of general limit equilibrium analysis for the slope failure mode on driving zone and resistance zone, which based on the stress level step according to failure ratio. Through the variation of shear strain for the variation of inserting angle of reinforcements, the different mechanism on the bending and the shear resistance of reinforcements was shown fair possibility.

• 무역상무연구
• /
• 제37권
• /
• pp.217-250
• /
• 2008

The International Ship and Port Facility Security (ISPS) Code which was developed as the main response of the shipping sector to the miserable event of 11 September 2001 came into effect on 1 July 2004. The ISPS Code designed to detect and eliminate security threats affecting ships and port facilities used in international trade will significantly impact not only on the management and operation of the shipping industry but also on maritime law despite the fact that it is the regulatory framework of public law. It is expected that implementing the ISPS Code will contribute to reinforcement of maritime security on the one hand. However, on the other hand, more intensified security inspection and control measures of port states will also cause delay and additional costs which cause uncertainty in allocating security risk and cost between the contracting parties. Therefore, it is desire to insert new security clause dealing with main security issues or adapt existing clauses to new shipping environments to minimize disputes.

• 한국기계가공학회지
• /
• 제20권12호
• /
• pp.8-15
• /
• 2021

Cold forging is a method in which molding is performed at room temperature. It has a high material recovery rate and dimensional precision and produces excellent surface quality, and it is mainly used for the production of bolted or housing products. The lifespan of cold forging molds is generally determined by the wear of the mold, plastic deformation of the mold, and fatigue strength. Cold forging molds are frequently damaged due to fatigue destruction rather than wear and plastic deformation in a high-temperature environment as it is molded at room temperature without preheating the raw material and mold. Based on the results analyzed through FEM, an effective mold structure design method was proposed by analyzing the changes in tensile and compressive stresses on molds according to the number of molds and reinforcement rings and comparing the product geometry and mold stress using three existing mold models.

• Journal of the Korean Wood Science and Technology
• /
• 제41권1호
• /
• pp.51-57
• /
• 2013

직물형 유리섬유 조합에 따른 보강 집성재의 볼트 접합부 전단 성능을 알아보기 위하여 인장형 전단시험을 실시하였다. 보강재는 직물형 유리섬유로서 유리섬유 배열 형태는 평직형과 능직형을 사용하였다. 보강 집성재는 5층으로 직물형 유리섬유의 삽입 위치와 조합 형태를 달리하여 층재 사이에 삽입 적층시켜 제작하였다. 인장형 전단 시험편은 강판 삽입형로서 끝면거리 7D에 직경 12, 16 mm의 볼트로 접합하였다. 체적비 1% 직물형 유리섬유 보강 집성재의 경우 12 mm 볼트 접합부의 항복 전단내력은 집성재 외층부보다 내층부를 보강한 시험편에서 10% 큰 값을 나타내었다. 체적비 2% 직물형 유리섬유 보강 집성재의 항복 전단내력은 12 mm 볼트 접합부의 경우 각층재 사이에 삽입 적층시킨 시험편이 보강하지 않은 접합부보다 약 22% 향상되었으며, 16 mm 볼트 접합부의 항복 전단내력은 약 20% 향상되었다.

• 터널과지하공간
• /
• 제33권6호
• /
• pp.519-533
• /
• 2023

본 연구에서는 평균 압축강도가 100 MPa 이상인 암석에 대해 픽커터의 선형절삭시험을 실시하였고, 적외선 열화상 카메라를 통해 측정된 픽커터 절삭 시의 발생 온도와 커터 작용력과의 상관관계를 분석하였다. 모든 시험조건에서 최대 온도는 치핑이 발생하는 암석면에서 측정되었고, 암석에 발생한 온도는 픽커터의 작용력과 밀접한 상관관계를 나타내었다. 반면, 픽커터에 발생하는 온도는 대기 온도 대비 최대 36℃ 이내로 상승하였고 커터 작용력과의 상관관계도 뚜렷하지 않았다. 이는 실험실 조건의 짧은 절삭거리와 텅스텐 카바이드 삽입재의 높은 열전도 특성이 원인인 것으로 사료된다. 단, 픽커터의 주요 부위 중에 텅스텐 카바이드 삽입재에 상대적으로 높은 온도가 유지되는 것으로 나타나, 픽커터 절삭 성능의 유지를 위해서는 삽입재와 헤드부 사이에 보강을 실시하거나 픽커터 제작 시에 은납 공정의 품질을 향상시키는 것이 필요할 것으로 판단된다.