• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.10 s.101
• /
• pp.1050-1058
• /
• 2005

This paper presents how to design and implement a very compact, cost effective and broad band receiver module for IEEE 802.16 FWA(Fixed Wireless Access) in the 40 GHz band. The presented receiver module is fabricated in a multi-layer LTCC(Low Temperature Cofired Ceramic) technology with cavity process to achieve excellent electrical performances. The receiver consists of two MMICs, low noise amplifier and sub-harmonic mixer, an embedded image rejection filter and an IF amplifier. CB-CPW, stripline, several bond wires and various transitions to connect each element are optimally designed to keep transmission loss low and module compact in size. The LTCC is composed of 6 layers of Dupont DP-943 with relative permittivity of 7.1. The thickness of each layer is 100 um. The implemented module is $20{\times}7.5{\times}1.5\;mm^3$ in size and shows an overall noise figure of 4.8 dB, an overall down conversion gain of 19.83 dB, input P1 dB of -22.8 dBm and image rejection value of 36.6 dBc. Furthermore, experimental results demonstrate that the receiver module is suitable for detection of Digital TV signal transmitted after up-conversion of $560\~590\;MHz$ band to 40 GHz.

• Korean Journal of Environment and Ecology
• /
• v.14 no.1
• /
• pp.38-45
• /
• 2000

This research has been done to investigate influence of soil physical and chemical properties on forest environmental change by fired pine forest in Koseong, Kangwondo. The sample sites were divided by not-fired sites(NF), not-cutting site after fired(FNC), cutting and planting sites after fired(FCP) and cutting and not-planting sites after fired(FC). Soil texture of whole sites was sandy clay loam. Sand content of NF top soil were lower than those of sub soil and clay content were higher, while FNC, FCP and FC sand content of top soil were higher than those of sub soil. Total porosity didn't differ between the sites. Coarse porosity and permeability had the increasing order as NF> FNC> FCP> FC, but fine porosity and bulk density had the opposite trends. Because forest fire removed the vegetation and then soil erosion was accelerated, forest environmental changes by forest fire greatly degraded soil porosity and permeability which were indices for forest water retention, so that soil physical properties were deteriorated. Both top and sub soil pHs of NF and FNC were higher than those of FCP and FC. Organic matter content and total nitrogen content of top and sub soils were high in order as NF> FNC> FCP> FC. Cation exchange capacities and exchangeable cation(K+, Na+, $Ca^2$+, $Mg^2$+) content in top soils were higher than those in sub soils, and in order as NF> FNC> FCP> FC, to be compared by the sites. Those mean that forest fire result from the erosion of top soil layers.

• Journal of Korean Society of Transportation
• /
• v.20 no.4
• /
• pp.151-162
• /
• 2002

The object of this study is to develop an operating time prediction model for expressways using toll collection data. A Prediction model based on modular neural network model was developed and tested using real data. Two toll collection system(TCS) data set. Seoul-Suwon section for short range and Seoul-Daejeon section for long range, in Kyongbu expressway line were collected and analyzed. A time series analysis on TCS data indicated that operating times on both ranges are in reasonable prediction ranges. It was also found that prediction for the long section was more complex than that for the short section. However, a long term prediction for the short section turned out to be more difficult than that for the long section because of the higher sensitivity to initial condition. An application of the suggested model produced accurate prediction time. The features of suggested prediction model are in the requirement of minimum (3) input layers and in the ability of stable operating time prediction.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.51-51
• /
• 2010

Recently just as in the automobile industry, shipbuilders also try to reduce material consumption and weight in order to keep operating costs as low as possible and improve the speed of production. Naturally industry is ever searching for welding techniques offering higher power, higher productivity and a better quality. Therefore it is important to have a details research based on the various welding process applied to steel and other materials, and to have the ability both to counsel interested companies and to evaluate the feasibility of implementation of this process. Submerged-arc welding (SAW) process is usually used about 20% of shipbuilding. Similar to gas metal arc welding(GMAW), SAW involves formation of an arc between a continuously-fed bare wire electrode and the work-piece. The process uses a flux to generate protective gases and slag, and to add alloying elements to the weld pool and a shielding gas is not required. Prior to welding, a thin layer of flux powder is placed on the work-piece surface. The arc moves along the joint line and as it does so, excess flux is recycled via a hopper. Remaining fused slag layers can be easily removed after welding. As the arc is completely covered by the flux layer, heat loss is extremely low. This produces a thermal efficiency as high as 60% (compared with 25% for manual metal arc). SAW process offers many advantages compared to conventional CO2 welding process. The main advantages of SAW are higher welding speed, facility of workers, less deformation and better than bead shape & strength of welded joint because there is no visible arc light, welding is spatter-free, fully-mechanized or automatic process, high travel speed, and depth of penetration and chemical composition of the deposited weld metal. However it is difficult to application of thin plate according to high heat input. So this paper has been focused on application of the field according to SAW process for thin plate in ship-structures. For this purpose, It has been decided to optimized welding condition by experiments, relationship between welding parameters and bead shapes, mechanical test such as tensile and bending. Also finite element(FE) based numerical comparison of thermal history and welding residual stress in A-grade 3.2 thickness steel of SAW been made in this study. From the result of this study, It makes substantial saving of time and manufacturing cost and raises the quality of product.

• Korean Journal of Soil Science and Fertilizer
• /
• v.14 no.1
• /
• pp.8-16
• /
• 1981

A mathematical model based on the water flow equation was developed with the Ohm's analogy and the partial differential equations. Simulation of water uptake was performed by numerically solving the equations with the aid of a differential equation solver, DGEAR in IMSL package, in FORTRAN version. The input data necessary were climatological parameters (temperature, solar radiation, humidity and wind speed). plant parametors (leaf water potential, leaf area, root conductivity and root length density) and soil parameters (hydraulic conductivity and The graphical comparison of the simulated and measured water contents as the functions of time showed good agreement, but there still was some disparity due to possible inacouracy of the field measured parameters. The simulated soil evaporation showed about 2 mm/day early in the growing period and dropped to about 0.4 mm/day as the full canopy developed and the soil water depleted. During the dry period, soil evaporation was as low as 0.1 mm/day. The transpiration was as high as 5mm/day. Deep percolation calculated from the flux between the 180-cm layer was about 0.2mm/day and became smaller with time. After the soil water of upper layers depleted, the flux reversed showing capillary rise. The rate of the capillary rise reached about 0.07mm/day, which was too low to satisfy water uptake of the root system. Therefore, to increase use of water in deep soil, expansion of the root system is necessary.

• Journal of the Korea Convergence Society
• /
• v.9 no.9
• /
• pp.431-440
• /
• 2018

In this study, authors predicted probability of resignation of newly employed nurses using TensorFlow, an open source software library for numerical computation and machine learning developed by Google, and suggested strategic human resources management plan. Data of 1,018 nurses who resigned between 2010 and 2017 in single university hospital were collected. After the order of data were randomly shuffled, 80% of total data were used for machine leaning and the remaining data were used for testing purpose. We utilized multiple neural network with one input layer, one output layer and 3 hidden layers. The machine-learning algorithm correctly predicted for 88.7% of resignation of nursing staff with in one year of employment and 79.8% of that within 3 years of employment. Most of resigned nurses were in their late 20s and 30s. Leading causes of resignation were marriage, childbirth, childcare and personal affairs. However, the most common cause of resignation of nursing staff with in one year of employment were maladaptation to the work and problems in interpersonal relationship.

• Journal of Broadcast Engineering
• /
• v.25 no.4
• /
• pp.545-559
• /
• 2020

In this paper, we propose a content creation framework that enables users without programming experience to easily create interactive media content that responds to user gestures. In the proposed framework, users define the gestures they use and the media effects that respond to them by numbers, and link them in a text-based configuration file. In the proposed framework, the interactive media content that responds to the user's gesture is linked with the dynamic projection mapping module to track the user's location and project the media effects onto the user. To reduce the processing speed and memory burden of the gesture recognition, the user's movement is expressed as a gray scale motion history image. We designed a convolutional neural network model for gesture recognition using motion history images as input data. The number of network layers and hyperparameters of the convolutional neural network model were determined through experiments that recognize five gestures, and applied to the proposed framework. In the gesture recognition experiment, we obtained a recognition accuracy of 97.96% and a processing speed of 12.04 FPS. In the experiment connected with the three media effects, we confirmed that the intended media effect was appropriately displayed in real-time according to the user's gesture.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.29 no.4
• /
• pp.415-430
• /
• 1996

Spatio-temporal variations in zooplankton community and ropepod indicator species were investigated along with the interaction between zooplankton distribution and environmental factors in Chinhae Bay. Zooplankton samples were monthly collected at 7 stations from February to September in 1993. A NORPAC net was vertically hauled from bottom to surface, At the same station, environmental factors such as temperature, salinity and COD (chemical oxygen demand) were measured at two different water layers, surface and bottom. In August and September, salinity declined below 30.00‰ , while eutrophic parameters such as COD showed the higher concentrations than those in other months, with higher concentrations at inner bay stations. Salinities were, however, higher at bay mouth areas. These distributional patterns were believed to be caused by input and dispersion of organic matters from nearby land. Zooplankton communities were composed of 7~14. Of these, Noctiluca scintillans was predominant and occupied 90.6‰ of total zooplankton abundance. Cladocera and Copepoda were secondly abundant taxa. Among 6 to 10 copepod species appeared, Acartia omorii and A. hudsonics were most common species during the survey months except March and September. Species diversities were greater, in general, at inner bay than outer bay. The lowest diversity index was observed in February, while the highest in July. Cluster analysis could divide the study area into 2 or 4 zones for each month. Zone 1, mouth area of the bay, was characterized by the influence of offshore waters. Zone II was mixing area. Zone III and IV seemed to be affected by nearby land.

• Journal of the Korea Computer Graphics Society
• /
• v.22 no.5
• /
• pp.17-26
• /
• 2016

This paper presents an adaptive slicing method based on merging vertical layer polylines. Firstly, we slice the input 3D polygon model uniformly with the minimum printable thickness, which results in bounding polylines of the cross section at each layer. Next, we group a set of layer polylines according to vertical connectivity. We then remove polylines in overdense area of each group. The number of layers to merge is determined by the layer thickness computed using the cusp height of the layer. A set of layer polylines are merged into a single polyline by removing the polylines within the layer thickness. The proposed method maintains the shape features as well as reduces the printing time. For evaluation, we sliced ten 3D polygon models using our method and a global adaptive slicing method and measured the total length of polylines which determines the printing time. The result showed that the total length from our method was shorter than the other method for all ten models, which meant that our method achieved less printing time.

• Geophysics and Geophysical Exploration
• /
• v.19 no.2
• /
• pp.76-83
• /
• 2016

Migration image can be distorted due to reflected waves in the source and receiver wavefields when discontinuities of input velocity model exist in seismic imaging. To remove reflected waves coming from layer interfaces, it is a common practice to smooth the velocity model for migration. If the velocity model is smoothed, however, the subsurface image can be distorted because the velocity changes around interfaces. In this paper, we attempt to minimize the distortion by reducing reflection energy in the source and receiver wavefields through acoustic impedance homogenization. To make acoustic impedance constant, we define fake density model and use it for migration. When the acoustic impedance is constant over all layers, the reflection coefficient at normal incidence becomes zero and the minimized reflection energy results in the improvement of migration result. To verify our algorithm, we implement the reverse-time migration using cell-based finite-difference method. Through numerical examples, we can note that the migration image is improved at the layer interfaces with high velocity contrast, and it shows the marked improvement particularly in the shallow part.