• Proceedings of the Korean Information Science Society Conference
• /
• 2004.10c
• /
• pp.301-303
• /
• 2004

현재 ATM 망에서 다양한 형태의 스위치 구조가 제안 되었으며 스위치 구조는 크게blocking 과 nonblocking 스위치로 나눌 수 있다. nonblocking 스위치는 버퍼의 위치에 따라 input queuing, output queuing, shared buffer switch로 나뉘며 그 중에 입력 버퍼형은 하드웨어 구현이 쉬운 장점이 있으나 HOL블로킹으로 인하여 처리 효율이 낮다는 단점이 있다. 본 논문에서는 이러한 입력 버퍼형 ATM 교환기의 문제점을 해결하기 위하여 가상적인 입력버퍼와 MUX를 이용한 입력버퍼형 반얀 스위치 모델을 제안한다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.5
• /
• pp.1184-1195
• /
• 1998

In this paper, we compare vaious input-buffered ATM switch architectures in structures on input buffer and switching fabric, the resons for performance improvement and degradation, arbitration scheme and maximum throughput, and present comparative merits and demerits of each architecture under random and bursty traffic. We also analyze the prformance of combined architectures of windowing scheme, destination-queueing based input-port expansion schemeand output-port expansion scheme, and show that it is possible to achieve 100% throughput with combined scheme of destination-queueing based input-port expansion scheme and output-port expansio scheme when the number of output group is 2 and output port expansion ratio is 2.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.8 no.6
• /
• pp.8-16
• /
• 1971

This paper describes the transistorized linear counting ratemeter which can be uses to indicate on the meter or record the counting rates of the nuclear radiations produced from the atomic reactor or from the radio isotopes. Tte feature of this ratemeter is the use of the transistor chopper for good stabilization. At the input stage of the a. c. amplifier a composite emitter follower buffer stage has been used to give the high input impedance. A hybrid parameter equivalent circuit was modeled for the analysis of this buffer stage. The counting rates can be linearly measured from few CPS up to 100KCPS in 4 ranges. The resolution is less than 0.5$\mu$sec and the output drift at the room temperature with 7-hour continuous operation is in the order of $\pm$0.5$\mu$A.

• Proceedings of the IEEK Conference
• /
• 2000.07a
• /
• pp.537-540
• /
• 2000

In this paper, we propose and design new architecture of the modified Banyan switch for a high speed networking and the high speed parallel computer. The proposed switching network with a remodeled architecture is a newly modified Banyan network with eight input and output ports. The switch scheme is that two packets may arrive on different inputs destined for the same output. We have analyzed the maximum throughput of the revised switch. The result of the analyses shows good agreement simulation and if we adopt such architecture of the revised model of the Banyan switch, the hardware complexity can be reduced. The FIFO discipline has increased about lloio when we compare the switching system with the input buffer system. We have designed and verified the switching system in VHDL.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1996.04a
• /
• pp.294-296
• /
• 1996

JIT(just-in-time) 생산시스템은 제조라인의 재공품 재고량을 최소화하고, 필요한 품목을 적시에 필요한 양만큼만 생산하여 공급하는 것을 목적으로 한다. 이러한 시스템은 사용하는 칸반의 수에 따라 single-card kanban system과 two-card kanban system으로 구별할 수 있다. 또한 각 공정이 입력버퍼(input buffer)와 출력버퍼(output buffer)를 갖는 경우와 공정간에 하나의 버퍼를 갖는 경우로 나누어 볼 수 있다. 본 연구는 기계간의 물류(material handling)가 필요한 시점에 즉시 이루어진다는 가정하에 기계간 버퍼가 하나이고, 그 버퍼의 용량이 1인 경우의 single-card kanban의 효율적인 운용방안을 개발하였다. 본 연구의 목적은 생산지시칸반의 회수시기를 적절히 조절하여 생산라인의 이용효율(utilization)을 극대화하고자 하는 것이다. 칸반회수시기 결정을 위한 상황분석의 범위를 10대의 기계로 제한하여 시뮬레이션에 의해 분석하였다. 기존의 칸반운영방식과 생산라인에서의 재고를 최소화하는 운영 알고리듬, 그리고 생산기계의 효율을 최대화할 수 있는 운영 알고리듬을 개발하여 비교.분석하였다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.398-401
• /
• 2011

This paper presents a high-efficiency CMOS PWM DC-DC buck converter. It generates a constant output voltage(1-2.8V), from an input voltage(3.4-3.9V). Inductor-based type is chosen and inductor current is controlled with PWM operation. The designed circuit consists of power switch, Pulse Width Generation, Buffer, Zero Current Sensing, Current Sensing Circuit, Clock & Ramp generation, V-I Converter, Soft Start, Compensator and Modulator. Switching Frequency is 1MHz, It operates in CCM when the load current is more than 40mA, and the maximum efficiency is 98.71% at 100mA. Output voltage ripple is 0.98mV(input voltage:3.5V, output voltage:2.5V). The performance of the designed circuit has been verified through extensive simulation using a CMOS $0.18{\mu}m$ technology.

• Journal of the Korea Society of Computer and Information
• /
• v.7 no.2
• /
• pp.115-123
• /
• 2002

This thesis proposes a new type of Input-Output Buffered ATM Switch which employs an arbiter and its performance under different traffic conditions studied. The proposed switch is designed with a view to exploit the architecture and other characteristics of the arbiter. The primary aim of the proposed switch is the elimination, or at least, the reduction of HOL blocking phenomenon which occurs in the simple input buffered switch. Several HOL arbitration algorithms have been proposed for this purpose in the literature. The proposed switch attempts to reduce the HOL blocking as it uses the arbiter and the buffer at the output port in an effective manner. The arbiter is designed to work with Three Phase Algorithm which is one of the many well known HOL arbitration algorithms. The Proposed switch acquires control over priority transmission through the REQ signal. As the signals are transmitted to the arbiter, the latter controls the one which is sent by the input buffer. Computer simulation results have been provided to demonstrate the effectiveness of the Proposed switch under uniform traffic conditions.

• Journal of the Korea Society of Computer and Information
• /
• v.8 no.2
• /
• pp.97-105
• /
• 2003

This thesis proposes a new type of Input-Output Buffered ATM Switch which employs an arbiter and its performance under different traffic conditions studied. The proposed switch is designed with a view to exploit the architecture and other characteristics of the arbiter The primary aim of the proposed switch is the elimination, or at least, the reduction of HOL blocking phenomenon which occurs in the simple input buffered switch. Several HOL arbitration algorithms have been proposed for this purpose in the literature. The Proposed switch attempts to reduce the HOL blocking as it uses the arbiter and the buffer at the output Port in an effective manner. The arbiter is designed to work with Three Phase Algorithm which is one of the many well known HOL arbitration algorithms . The proposed switch acquires control over priority transmission through the REd signal. As the signals are transmitted to the arbiter, the latter controls the one which is sent by the input buffer. Computer simulation results have been provided to demonstrate the effectiveness of the proposed switch under non-uniform random traffic conditions.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.9
• /
• pp.73-80
• /
• 2004

In this paper, we present the cell resequencing buffer to solve the cell sequence integrity problem of the Cyclic banyan network that is a high-performance fault-tolerant cell switch. By offering multiple paths between input ports and output ports, using the deflection self-routing, the Cyclic banyan switch offer high reliability, and it also solves congestion problem for the internal links of the switch. By the way, these multiple paths can be different lengths for each other. Therefore, the cells departing from an identical source port and arriving at an identical destination port can reach to the output port as the order that is different from the order arriving at input port. The proposed cell resequencing buffer is a hardware sliding window mechanism. to solve such cell sequence integrity problem. To calculate the size of sliding window that cause the prime cost of the presented device, we analyzed the distribution of the cell delay through the simulation analyses under traffic load that have a nonuniform address distribution that express tile Property of traffic of the Internet. Through these analyses, we found out that we can make a cell resequencing buffer by which the cell sequence integrity is to be secured, by using a, few of ordinary memory and control logic. The cell resequencing buffer presented in this paper can be used for other multiple paths switching networks.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.4
• /
• pp.745-752
• /
• 2005

In this paper we propose and implement a digital part of a receiver system for identifying a moving object and its tracking position in wireless environment. We assumed UWB(Ultra Wide Band)-based communication system for target application and used serial communication method(RS-232). The proposed digital receiver consists of RS-232-type1/RS-232-type2 for input and output of serial communication, ID Detector for detecting IDs, and PISO&Buffer circuit to buffer input signals for appropriate operation of ID Detector. We implemented the digital receiver with minimal hardware(H/W) resource according to target application of UWB-based communication system. So it correlates input patterns with pre-stored patterns though repeated detecting method for multiple IDs. Since it has reference panerns in the Ve-stored form, it can detect various IDs instantly. Also we can program content and size of reference patterns considering compatibility with other systems .The implemented H/W was mapped into XC2S100PQ208-5 FPGA of Xilinx, occupied 727($30\%$) cells, and stably operated in the clock frequency of 75MHz(13.341ns).