• 한국음향학회지
• /
• 제25권1호
• /
• pp.1-6
• /
• 2006

천해에서의 수중음장 계산에서 음향 임피던스를 해저면 입력인자로서 도입하는 방안의 가능성을 고찰하였다. 먼저 탄성 해저면에서의 음파반사 특성을 고찰한 결과, 임계 접지각 이하에서 음향 임피던스는 접지각이 거의 $0^{\circ}$에 가까울 때의 임피던스 $Z_0$ 1개 값으로 근사가 가능함을 나타내었다. 이러한 특성과 'effective depth' 개념을 접목시켜 전달손실을 계산한 결과, 수중음장 계산에서 임피던스를 해저면 음향 특성을 나타내는 입력인자로 사용하는 것이 가능성이 있음을 확인하였다.

• 한국소음진동공학회논문집
• /
• 제23권10호
• /
• pp.920-927
• /
• 2013

The requirement of acoustic performance about underwater acoustic material which is used in underwater environment more increases. Underwater acoustic material was made by viscoelastic material such as a rubber and a polyurethane etc. In order to increase an acoustic performance, several kinds of inclusions were added to viscoelastic material. In this paper, acoustic modelling and analysis techniques were introduced and the acoustic characteristics of underwater acoustic material were studied. Echo reduction and transmission loss were calculated with volume fraction of inclusion in the material. Also the characteristic impedance and the input impedance of underwater acoustic material were obtained and effects on the echo reduction and transmission loss of material were discussed.

• 한국소음진동공학회논문집
• /
• 제24권7호
• /
• pp.537-548
• /
• 2014

In this paper, horn loudspeaker modeling was suggested, investigated and verified through comparison of test results and simulation ones based on input electrical impedance curves and acoustic sensitivity ones. First, Thiele Small parameters of horn driver were identified by using pseudo loudspeaker model concept and verified in case of both closed and open horndriver. Second, cone-shaped horn models were investigated and compared with input acoustic impedance curves for real horn(cone angle $6.6^{\circ}$) and short horn(cone angle $27.9^{\circ}$). It showed that Leach model for cone horn was well described to test results, which were electrical impedance and acoustic sensitivity, compared to Lemaitre one. To represent horn system model good approximation in wide frequency range, mass correction filter and lowpass filter were adopted and consequently showed good fitted to test results.

• 한국전자파학회논문지
• /
• 제14권4호
• /
• pp.323-329
• /
• 2003

본 논문에서는 유전자 알고리즘을 이용한 FBAR(Thin-Film Bulk Acoustic Resonator)에서의 물질 상수 추출 기법을 제안하였다. 제안된 기법은 유전자 알고리즘을 적용하여 FBAR의 입력 임피던스로부터 물질 상수를 추출하는 방법이다. 유전자 알고리즘의 적합도 함수를 결정하기 위해 물질 상수 변화가 FBAR의 임피던스 특성에 미치는 영향을 알아본 후, FBAR의 입력 임피던스로부터 구해지는 직렬/병렬 공진 주파수와 FBAR 대역폭으로 적합도를 평가하였다. 유전자 알고리즘의 흐름도와 제안된 물질 상수 추출 과정에 대해 설명하였고, 본 기법의 타당성을 검증하기 위해 물질 상수 추출 결과를 제시하였다.

• 센서학회지
• /
• 제27권6호
• /
• pp.374-379
• /
• 2018

The piezocomposite transducer is widely used because it is highly efficient in transforming electric energy into mechanical energy, and its frequency range is broader than that of other types of ultrasound transducers. A general piezocomposite transducer is composed of an acoustic lens, impedance matching layers, piezoelectric materials, and backing layers. When an input voltage is applied to a piezoelectric material as an active material, it generates sound waves while vibrating. At that time, an impedance matching layer helps the sound waves to propagate forward while reducing the impedance mismatch that may occur at the interface between the active material and its front material. The impedance mismatch has a negative effect on the signal of an ultrasound transducer; thus, it is important to design a matching layer to overcome the issue. In this study, an optimized feature of a matching layer with gradient properties is studied. An objective function is defined to minimize both the average and the deviation of the reflection coefficients that are functions of the frequencies. As a result, an improvement in the signal characteristics with respect to the sensitivity and bandwidth is reported.

• Journal of Biosystems Engineering
• /
• 제34권4호
• /
• pp.260-268
• /
• 2009

As a basic study to develop a high sensitive biosensor using film bulk acoustic resonator, the mathematical model for analyzing the resonance characteristics of bulk acoustic resonator with acoustic Bragg reflectors was investigated. The simulation results due to the number of acoustic Bragg reflectors with low and high acoustic impedance materials were compared with the experimental results for 1, 2.25 and 5 MHz of PZT based bulk acoustic resonators with various acoustic Bragg reflectors. At the fabricated bulk acoustic resonator with an odd number of acoustic Bragg reflectors, low and high acoustic impedance materials in sequence under the bottom electrode showed better resonance characteristics than even number of acoustic Bragg reflectors. The changes of resonance frequencies due to the increase of number of acoustic Bragg reflectors by simulation and experiment, respectively showed approximately similar tendency but some differences in input impedance between the experiment and simulation were found. The derived mathematical model for describing the resonance characteristics of the bulk acoustic resonator with acoustic Bragg reflector will be available for analyzing the design parameters for development of biosensor using bulk acoustic resonator.

• 한국음향학회지
• /
• 제11권6호
• /
• pp.32-40
• /
• 1992

This study shows how the finite element method for the structural problems could be applied in the electromechanical impedance analysis of an in-air piezoelectric cylinder transducer and then compares the numerical results by the FEM with the measured results using the impedance analyzer. The results also show that the comparison between both results could be applied to examine the mechanical properties of the added unknown material to transducer such as an acoustic window.

• 대한전자공학회논문지SD
• /
• 제42권1호
• /
• pp.9-17
• /
• 2005

공진주파수 스펙트럼법을 이용하여 ZnO 와 AIN 압전박막의 임피던스 특성 및 전기기계결합계수 특성에 대해 조사하였다. 압전박막의 두께가 얇을수록 전체적인 임피던스 응답 피크의 크기가 감소하였으며, 기판의 두께가 얇을수록 응답 피크의 모드 수가 감소하는 것이 관찰되었다. 입력 Kt² 값으로부터 평가된 Kt² 값을 통해 압전박막의 두께보다 기판의 두께 변화에 대한 영향이 더 큼을 알 수 있었고, 기판의 acoustic 임피던스에 의해서도 Kt² 값이 감소함을 알 수 있었다. 전극 효과가 첨가되면 임피던스 응답 피크의 크기가 감소하였으며, 전극의 acoustic 임피던스가 커짐에 따라 응답피크는 더 작아졌다. 공진주파수 스펙트럼법에서 전극은 질량부하로 고려되기 때문에 전극 효과가 첨가된 경우 Keff² 값은 증가하며, 전극의 acoustic 임피던스가 크면 그 효과는 더 커졌다. 공진주파수 스펙트럼법을 이용한 시뮬레이션을 통해 기판, 압전체, 전극으로 이루어진 composite 공진기의 특성 분석과 설계까지도 가능함을 알 수 있었다.

• 한국음향학회지
• /
• 제16권4호
• /
• pp.101-105
• /
• 1997

본 논문에서는 길이가 긴 덕트를 대상으로 개발된 능동소음제어 방법이 길이가 짧은 덕트에서 적용될 수 없는 문제점을 해결하기 위하여 음향 임피던스 0의 경계면에 의한 SISO(Single Input Single Output)알고리듬을 적용하였다. 하나의 마이크로폰으로 소음원의 입력과 에러 감지를 동시에 할 수 있는 SISO제어기는 TMS320E25 DSP(Digital Signal Processing)칩을 이용하여 실시간으로 구현하고 실험을 통하여 그 성능을 평가하였다. 길이가 0.80m인 짧은 덕트를 대상으로 실험한 결과 전체적으로 4.7dBA의 소음저감을 얻었다.

• 한국소음진동공학회논문집
• /
• 제27권2호
• /
• pp.139-147
• /
• 2017

Acoustic performance of splitter silencers was investigated by using 3-dimensional commercial software and experiments. Flow resistivity of sound absorbing material was indirectly estimated by using an impedance tube setup and a curve fitting method. In addition the acoustic impedance of perforated plate was determined by an empirical formulation. Such properties have been used as input parameters in the commercial software. The prediction for a splitter silencer with 1000 mm length was compared with the experimental result. The numerical method is then applied to identify the effects of number of splitters, length of splitters, absorptive material density, and porosity of a perforated plate on the performance of the splitter silencers. As the number and length of splitter increases, the acoustic performance significantly increases. Although the increase of density of absorptive material also increase the acoustic performance, a change in the density over a certain level hardly affect it. The increase of porosity will enhance the performance especially at higher frequencies.