• 대한기계학회논문집A
• /
• 제34권7호
• /
• pp.891-896
• /
• 2010

제로터는 유압모터나 펌프뿐만 아니라 조향장치인 파워 스티어링 유닛(PSU)에도 사용된다. 제로터의 내치차는 일상적인 경우 단일 원호형상의 외치차에 의하여 생성된다. 본 논문에서 PSU의 특성 개선을 위하여 보다 일반화 된 외치차의 형상으로부터 내치차를 생성하는 방법을 해석하였다. 해석의 결과로서, 외치차의 형상곡선이 특별한 2중곡률을 갖는 원호인 경우에 대하여, 내치차의 형상과 곡률, 제로터의 유량 및 접촉점의 위치와 슬립속도 등의 설계자료를 구하여 제시하였다. 이러한 해석은 새로운 PSU의 개발과 소형화를 가능케 한다.

• Composites Research
• /
• 제18권1호
• /
• pp.45-54
• /
• 2005

필라멘트 와인딩 공정으로 제작된 고속 회전용 복합재 플라이휠 로터는 층간분리 현상에 의해 에너지 저장용량이 저하된다. 그리고 기존의 링 타입 허브는 복합재 로터 내측면에 인장력을 가하게 되고. 이는 로터내의 반경방향 인장응력을 가중시켜 로터의 한계 회전수를 저하시킨다. 복합재 로터의 응력해석을 위해서 2차원 평형방정식과 경계조건이 사용되었고, 이를 근거로 강도비를 최소화시키는 최적의 내압이 존재함을 수치적으로 제시하였다. 이러한 최적의 내압을 발생시키기 위해서 원주방향으로 분할된 스플릿 타입 허브를 제안하고, 링 타입과 스플릿 타입 허브의 두께변화에 따른 내압분포의 영향을 제시하였다. 스플릿 타입 허브의 유효성을 검증하기 위해 허브를 포함한 복합재 로터를 제작한 다음, 최대 회전수 40,000rpm까지 파손 없이 스핀 테스트를 수행하였다. 동시에 로터 표면에 4개의 원주방향 및 반경방향 스트레인게이지를 부착하여 변형률을 무선으로 측정하였다. 측정된 변형률은 해석결과와 매우 잘 일치하였다. 특히 반경방향의 응력을 크게 낮출 수 있었고, 반경방향으로 모두 압축 변형률이 발생함을 확인하였다. 결국 스플릿 타입 허브는 플라이휠 로터의 단점인 반경방향의 낮은 강도를 보안하는 효과를 나타내어, 저장에너지 밀도를 증가시킴으로써 대형 고출력 플라이횔 에너지 저장 시스템의 개발 가능성을 제시하였다.

• 한국자동차공학회논문집
• /
• 제25권2호
• /
• pp.201-206
• /
• 2017

In the study, the inner flow characteristics were analyzed by modifying the inner design parameter of the vane-type vacuum pump. The effect of pressure generated by the inner flow of pump on the rotor and vane was analyzed. The design parameter was analyzed using the angle variation of tilting and rotation of the vane. MRF was used for the analysis conducted using a virtual condition where the rotor and vane are rotated. The pressure gained from the load of the rotor and vane in the flow analysis is used for the structure analysis. Based on the results, the effect of variable vane design was revealed in structural strength. The effect of centrifugal and friction force generated during pump operation on structural strength was also analyzed.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 1999년도 제1회 학술대회논문집(KIASC 1st conference 99)
• /
• pp.117-120
• /
• 1999

This paper is about a modified induction generator which has a free inner-rotor. The improved induction generator utilizes a free inner-rotor that has a superconducting magnet. This kind of generator has same approach when analyzing as an ordinary induction generator, but shows a little difference when expressing in designing and analyzing such the machines.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2000년도 KIASC Conference 2000 / 2000년도 학술대회 논문집
• /
• pp.63-66
• /
• 2000

A rotating cryogenic system was designed similar to the cooling system for the rotor of a superconducting generator. The experimental rotor has an inner vessel which simulates the winding space of an actual superconducting rotor, and a torque tube of comparable design. This paper describes the evaluation of the total heat leak into the inner vessel that leads to the study of the jheat transfer characteristic of the rotating cryogenic system.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1051-1057
• /
• 2000

A projected 100 kW APU gas turbine rotor-bearing system has a main outer shaft, which is composed of some numbers of segmented sections for manufacturing and assembly conveniences. For a secure assembly of the segmented sections a tie shaft or inner shaft is installed inside of the outer shaft and a tensional axial preload of 50,000 N is provided to it. In this paper it is intended to set-up a sound modeling method of the APU rotor system, and particularly, the influences of the tie shaft on the rotordynamic characteristics of the entire APU gas turbine rotor-bearing system are investigated. Analysis results show that as a conservative design practice the inner tie shaft should be actively modeled in the rotordynamic analysis of the APU rotor-bearing system, and its effects on the dynamic behaviors of the outer shaft should be thoroughly design-reviewed.

• Tribology and Lubricants
• /
• 제12권3호
• /
• pp.100-106
• /
• 1996

Gerotor pumps and motors are widely used in lubrication and hydraulic actuator systems. Compared with internal gear pumps and motors, they have many advantages. However, the gerotor profiles have not been suff'lciently analyzed theoretically. Therefore, it is very difficult for designer to decide the specifications of the gemtor profiles, and calculation of flow rate and minimum distance of clearance in the contact point of inner and outer rotor is not yet confirmed. In this paper, when we design inner and outer rotor concurently, we have analyzed the gerotor profiles and displayed the calculated results such as flow rate, minimum distance between inner and outer rotor and gerotor profiles.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1996년도 제23회 학술대회
• /
• pp.17-23
• /
• 1996

Gerotor Pump and Motors are widely used in lubrication and hydraulic actuator systems, These have many advantage compared with internal gear pump and motors, But the gerotor profile have not been sufficiently analyzed theoretically. So it is vary difficult for designer to decide the specifications of the gerotor profile, and it is not yet confirmed to calculating flow rate and minimum distance of clearance in the contact point of inner and outer rotor. In this paper, When we design inner and outer rotor concurently, We have analyzed the gerotor and displayed the calculated results such as flow rate, minumum distance between inner and outer rotor and gerotor profiles

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.895-896
• /
• 2010

• Journal of Magnetics
• /
• 제20권3호
• /
• pp.265-272
• /
• 2015

In recent years, flux switching machines (FSMs) have been an attractive research topic owing to their tremendous advantages of robust rotor structure, high torque, and high power capability suitable for intensive applications. However, most of the investigations are focusing on the inner-rotor structure, which is incongruous for direct drive applications. In this study, high torque and power densities of a new 12S-14P outer-rotor permanent magnet (PM) FSM with a DC excitation coil was investigated based on two-dimensional finite element analysis for in-wheel direct drive electric vehicle (EV). Based on some design restrictions and specifications, design refinements were conducted on the original design machine by using the deterministic optimization approach. With only 1.0 kg PM, the final design machine achieved the maximum torque and power densities of 12.4 Nm/kg and 5.93 kW/kg, respectively, slightly better than the inner-rotor HEFSM and interior PM synchronous machine design for EV.