• The KSFM Journal of Fluid Machinery
• /
• v.10 no.1 s.40
• /
• pp.49-55
• /
• 2007

An 'Y' strainer type automatic flow rate regulating valve, which functions are to remove impurities from hot water inside the pipe and to maintain a constant flow rate regardless of variations of the differential pressure between valve inlet and outlet at the same time, is developed for distributing hot water equally to several pipes with district heating or central heating system. Numerical analysis of the three dimensional turbulent flow field in a valve shape is carried out to confirm the flow field whether the designed regulator shape is acceptable or not. The final developed valve improves installation time and cost and maintenance ability comparing with set-up 'Y' strainer and regulator separately. Tolerance for the nominal flow rate is also satisfied within ${\pm}5%$.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.5
• /
• pp.112-117
• /
• 2007

With the Euro-4 regulation coming into effect, the domestic car industry is forced to look for newer options to reduce NOX in the exhaust. EGR(Exhaust Gas Recirculation) Cooler is an effective method for the reduction of NOX form a diesel engine. High efficiency, low pressure loss and compactness are desirable features of an EGR Cooler. The cooling performance of EGR depends on the shape of tubes and the location of the entrance and exit. This paper reports the computational work conducted to estimate the performance of EGR cooler with three different cross section tubes and a triangular spiral tube. Three dimensional computation results show that the triangular tube is more effective than circular and rectangular tube. The most effective geometry is a triangular spiral tube with offset inlet and outlet locations.

• Proceedings of the KSRS Conference
• /
• 2004.10a
• /
• pp.566-569
• /
• 2004

This study is to trace the change of stream shape using the past series of aerial photographs, and to compare the land use changes of riparian area along the stream. For the Gyeongan national stream, aerial photographs of 1966, 1981 and 2000 were selected and ortho photographs were made with interior orientation and exterior orientation, respectively. As apparent changes of the stream, the consolidated reaches of stream with levee construction were straightened and their stream widths were widened. Especially the stream width of inlet part of Paldang lake was widened almost twice because of the rise of water level by dam construction in 1974. The land use maps (1966, 1981,2000) of riparian areas were also made, respectively and classified into 6 categories (water, forest, agricultural land, urban area, road, sandbar) by digitizing. The area of forest and agricultural land decreased and urban area increased as the stream maintenance was performed.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.998-1002
• /
• 2003

This paper investigates the characteristics of stiffness and load in the thrust bearing of spindle which could be changeable according to the groove shape of inlet, in order to design a high-stiffness air bearing by selecting a optimal groove shape. In experiments, dead weight and displacement sensor are used to measure the load carrying capacity and the stiffness respectively. Various shapes and different depth of groove of self-restrictor are used as experimental conditions. Comparative study between the theoretical value and the practical one by measuring the value of stiffness and load of the thrust bearing is performed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1764-1767
• /
• 2003

It is widely used in composite materials like several mechanical parts. aerospace industries. internal and structural materials of cars, building structures. ship materials and sporting goods. but it is insufficient to apply in field of mechanical processing. Therefore. GFRP which is possible to use in industrial field was examined about cutting force. tool wear condition of cutting, chip shape. surface roughness and inlet or outlet shape of processing parts with changing cutting condition and using HSS drill which is in vertical machining center in this paper.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.578-583
• /
• 1997

Abstract-Crosshead bearing in two-stroke marine diesel engine is operated under quite severe condition since the load on the bearing is sybject to the loading in a unidirectional and the sliding speed is very slow and oscillatory. So it is very difficult to form oil film and maintain the load. In this paper, two types of bearing are compared. One has large sized oil pocket and the seleted as multi-small oil grooves. Bearing clearance, oil inlet oressure and bearing types are selected as analysis parameters. Loci of journal center are presented to compare several cases. It is found that bearing clearance and shape affect to minimum film thickness.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.472-473
• /
• 2008

Flow boiling in parallel microchannels has received attention as an effective heat sink mechanism for power-densities encountered in microelectronic equipment. the bubble dynamics coupled with boiling heat transfer in microchannels is still not well understood due to the technological difficulties in obtaining detailed measurements of microscale two-phase flows. In this study, complete numerical simulation is performed to further clarify the dynamics of flow boiling in microchannels. The level set method for tracking the liquid-vapor interface is modified to include the effects of phase change and contact angle. The method is further extended to treat the no-slip and contact angle conditions on the immersed solid. Also, the reverse flow observed during flow boiling in parallel microchannels has been investigated. Based on the numerical results, the effects of channel shape and inlet area restriction on the bubble growth, reverse flow and heat transfer are quantified.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.5
• /
• pp.145-151
• /
• 2012

New design of catalytic converter is proposed by optimization of DFSS (Design For Six Sigma) and DOE (Design Of Experiment) method which is based on taguchi matrix. As a result of the optimization of design of catalytic converter, this paper classifies Exhaust-downpipe shapes with 3 parameters to increase flow velocity uniformity of front catalytic substrate face from CFD results. after finishing with L9 Taguchi test matrix, it can be found the main effect of each design parameter of concept model, and optimal design level. in conclusion, it can be increase flow uniformity from 0.60 upto 0.80 with optimal diffuser shape for Turbo-charger.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.5
• /
• pp.36-43
• /
• 2012

In this work the mixing and flow characteristics of a vane-type static mixer were investigated numerically for the reduction of NOx in the SCR-system of the diesel engines. The mixer was located in the 57 times pipe diameter away from the inlet. The analysis were performed by changing such various parameters as vane shape, angles, blockage ratio and location of the vane. The flow structure through the mixer was characterized by uniformity index and pressure drop. The results show that uniformity index and pressure coefficient are substantially influenced by the vane shape, angle, blockage ratio and position of the vane of the mixer.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2004.05b
• /
• pp.458-462
• /
• 2004

This study is to trace the change of stream shape using the past series of aerial photographs and compare the land use changes of inland along the stream. For the Gyeong-an national stream, aerial photographs of 1966, 1981 and 2000 was selected and ortho photograph was made with RMSE of 1.05, 0.54, 0.72 pixels, respectively. As apparent changes of the stream, the consolidated reaches of stream with levee construction were straightened and their stream width widened. Especially the stream width of inlet part of Paldang lake was widened almost twice because of the rise of water level by dam construction in 1974.