• 대한기계학회논문집
• /
• 제11권5호
• /
• pp.725-730
• /
• 1987

본 연구에서는 2사이클 기관의 흡입 포오트 부근의 가스 유동을 레이저 도플 러 유속계를 이용하여 측정하고 가스의 평균 속도, 속도 변동, 유속 벡터 등을 기관의 회전 속도, 실린더 헤드의 모양 및 실린더로의 흡입 속도 측정점의 위치 변화에 대하 여 비교 검토하고, 유동 특성을 고찰하였다.

• 한국자동차공학회논문집
• /
• 제11권3호
• /
• pp.99-105
• /
• 2003

The configuration of intake port is a dominant factor of inlet air flow and mixture formation in an engine. In this study, as an available technology to optimum intake port, the flow box system using resine has been applied. So we presents a methodology for estimating inlet flow characteristics in this paper. This quantified experimental result shows good agreements with visualization data in a cylinder. We obtained the optimal value of swirl ratio and flow coefficient under steady flow rig test for new development of intake port for heavy-duty engine. From this results, the cylinder heat with a good evaluated swirl flow characteristics was developed and adapted for a 11L heavy-duty engine using the liquid phase LPG injection (LPLi) system. This .research expects to clarify major factor that make the intake port efficiently.

• Journal of Biosystems Engineering
• /
• 제9권1호
• /
• pp.22-33
• /
• 1984

Husk separator is an indispensable equipment in rice milling plants. However, any basic research on the designing and operating criteria of the husk separator have rarely been conducted in Korea. According to the survey results reported recently, grain loss occurs in the process of rice husk separation at custom rice milling plants in Korea and the performance of husk separator has also not been identified. With this regard this study was conducted with a typical commercial husk separator to investigate the effect of the operational factors such as feed rate, blower speed and opening ratio on the velocity distribution in the air duct and the performance of the separator. The results are summerized as follows: 1. The average wind velocity in the primary air duct increased linearly with the blower rpm and the size of air inlet port in both cases of double type and single type operations. 2. The coefficient of variation in the horizontal wind velocities in the primary air duct was the minimum when the opening ratio was 0.22 ($0.052m^2$ of air inlet port) in both cases of single type and double type operations regardless of the blower speeds used in this test. The average wind velocity at the upper part of air duct was greater by 2-5 m/s than the velocity at the bottom part in double type operation. In case of single type operation, however, the average velocity in the middle part was greater than the upper or bottom part when the opening ratio was greater than 0.74. 3. The relationship between the overall effectiveness of separation(Ed for double type and Es for single type) and the average wind velocity (Va) in the primary air duct was expressed in the following quadratic functions. $$Ed=-190.84+106.18Va-10.052Va^2$$ ($r^2$ = 0.97782) $$Es=-223.76+106.23Va-9.1935Va^2$$ ($r^2$ = 0.97029) The average wind velocity required to obtain the overall effectiveness of separation more than 80% ranged from 4.04 m/sec to 5.84 m/sec in case of double type operation, and from 4.70 m/sec to 6.20 m/sec in case of single type. 4. An optimum wind velocity can be obtained with an increase in the blower speed or the size of air inlet port as presented in Figure 8. There was a tendency that the faster the blower speed, the narrower the control range of the air inlet port. 5. The feed rates (1850kg/hr and 2100kg/hr) adopted in this experiment did not bring about a significant difference in both the overall effectiveness of separation and the power consumption. 6. The energy consumption increased cubically with the blower speed but linearly with the size of the air inlet port. On the basis of the results described in items 1, 3, and 6, it would be more economic to adjust the size of the air inlet port larger with a relatively low blower speed than to adjust the size smaller with a relatively high speed.

• 태양에너지
• /
• 제11권2호
• /
• pp.34-40
• /
• 1991

Thermal stratification enhancement for the higher extraction efficiency of hot water storage tank was experimentally studied with transparent fiber glass cylindical tank($350{\ell}$, D=516mm, H=1680mm). Height to diameter ratio (H/D =1,2,3), flow rate(Q= 8,10,12LPM), inlet-outlet temperature differences(${\Delta}T=20,25,30^{\circ}C$), and geometry of inlet-outlet port were the parameters. In particular, three kind of distributors were used for geometry of inlet-outlet port. As a result, it was possible to get extraction efficiency of 95% by using the distributor having variable diameter but keeping a constant diameter of perforation. So it is recommendable to design the distributor so that the main pipe decrease in diameter toward the dead end.

• 설비공학논문집
• /
• 제14권6호
• /
• pp.503-511
• /
• 2002

Heat flow characteristics during hot water extraction process was studied experimentally. Data were taken at various outlet port type for the fixed inlet port type, inlet-outlet temperature differences and mass flow rates. In this study, the temperature distribution in a storage tank and an outlet temperature were measured to predict a degree of stratification in the storage tank, and a useful rate of hot water was analysed with respect to the variables dominating a extraction process. Experimental results show that the degree of stratification and useful rate of hot water are all high in a low flow rate in case of using modified distributor I (MDI) as the outlet port type.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.706-710
• /
• 2008

The experiment of dome port cover under shock impact is performed with shock tube. The dome port cover blocked intake air duct up from the solid propellant during air breathing vehicle speed reach Mach 2.0. When the air breathing vehicle reach Mach 2.0, the inlet cover is removed and the dome port cover is broken to pieces by detonator or pressure of inlet air. Thus the dome port cover not only must stand the pressure of combustion chamber but also easy to break from the RAM pressure. In this study, a fracture evaluation on the $Al_2O_3$ ceramic spherical dome and circular plate port under impact has been presented. Ceramic were supported by the rigid body and a couple of O-ring. The Mooney-Rivlin model have been used to describe behaviors of both O-ring. And spherical dome and circular plate fracture results of the LS-DYNA code using Johnson-Holmquist(JH-2) constitutive equation was compared.

• 태양에너지
• /
• 제10권3호
• /
• pp.3-12
• /
• 1990

본 실험연구에서는 탱크의 직경에 대한 높이의 비(H/D)가 3이고 유입 유량이 8LPM, 유입수의 온도와 기존 저장수와의 온도차, ${\Delta}T=30^{\circ}C$일때, 운동량교환을 최소화하여 가장 좋은 성층을 얻었고 또한 실험에서 사용한 유입구(Inlet Port)의 경우 수정 Richardson수(Modified Richardson Number), Ri가 0.004(Q=10LPM, ${\Delta}T=30^{\circ}C$) 이하의 값에서는 완전 혼합(Fully Mixing)이 발생하고 H/D가 작아질수록 혼합층의 두께($H^*/H$)가 증가하여 성층 축열에는 바람직하지 못하였다. 그리고 성층은 성층을 촉진시키기 위하여 Distributor를 사용했을 때가, Distributor를 사용하지 않은 유입구(Inlet Port)의 경우 보다 잘 형성되어 저장효율이 Distributor를 사용한 경우(Q=8LPM, ${\Delta}T=30^{\circ}C$, H/D=3)에 Distributor를 사용하지 않은 유입구(Inlet Port)의 최저효율 63%(Q=12LPM, ${\Delta}T=30^{\circ}C$, H/D=3인 경우)보다는 31% 정도, 최대효율 84%(Q=8LPM, ${\Delta}T=30^{\circ}C$, H/D=3인 경우)보다는 11% 정도 높은 95%까지 저장 효율을 증가시킬 수 있었다. 더 나아가서 단면이 균일한 원형 Distributor(A=D=Constant)의 경우에, 유량이 8LPM인 경우에 관내의 압력차가 작아 부분혼합(Partial Mixing)이 감소하여 안정된 성층을 얻을 수 있었다. 그리고, Distributor의 직경을 다음식과 같이 $$\frac{D}{D_L}=(\frac{x}{L})^{1/2}(1+\frac{fL}{2D})-\frac{fx}{2D_L}$$ 길이에 대하여 변화시켜 Distributor를 제작함으로써, 보다 안정된 열성층과 높은 열저장 효율을 얻을 수 있을 것으로 예상한다.

• 한국자동차공학회논문집
• /
• 제17권2호
• /
• pp.42-48
• /
• 2009

This paper is the second of 2 companion papers which investigate in-cylinder swirl generation characteristics according to inlet valve angle. Two DOHC 4 valve engines, one has wide intake valve angle and the other has narrow valve angle, were used to compare the characteristics of swirl motion generation in the cylinder. One intake port was deactivated to induce swirl flow. A PIV (Particle Image Velocimetry) was applied to measure in-cylinder velocity field according to inlet valve angle during intake stroke. The results show that the flow patterns of narrow valve engine are much more stable and well arranged compared with the normal engine over the entire intake and compression stroke except early intake stage, and very strong swirl motion is generated at the end of compression stage in this engine nevertheless using straight port which is unfavorable for swirl generating. In the wide valve angle one, however, strong swirl motion induced during intake stroke is destroyed as the compression progresses.

• 한국자동차공학회논문집
• /
• 제9권5호
• /
• pp.54-61
• /
• 2001

It is reported that during the cold starting, especially in gasoline engine, the engine response and the effect of HC emission can be improved by prompting atomization and reducing the quantity of fuel adhered to the range of injector tip, inlet port, and inlet valve. The purposes of this study are to promote atomization of fuel before air-fuel mixture in the inlet port. In order to achieve its goal, the glow plug is to evaluate the feasibility of for the early fuel evaporator and the spray behavior characteristics of gasoline, injected on the surface of glow plug with room temperature(2$0^{\circ}C$) and high temperature(25$0^{\circ}C$) is to examine. Particle motion analysis system(PMAS) was used to measure the SMD and the dropsize distribution of impinging spray and free spray. The results of this experiment, evaporation rate of impinging spray was higher than that of free spray, and the higher evaporation rate win, the smaller peak dropsize was. Especially, during early spray SMD of impinging spray was still smaller than that of fee spray.

• 대한기계학회논문집B
• /
• 제27권7호
• /
• pp.837-844
• /
• 2003

The exhaust gas flow in the inlet collector of close coupled catalyst(CCC) adapted to the exhaust manifold is very complex flow because the exhaust gas is a pulsation flow with several port flow. The distribution of gas flow and temperature in inlet collector effect to the efficiency of catalytic converter. In this study, it measures temperatures on several point in inlet collector with two kind of inlet collector volume. And it analyzes with CFD to exhaust manifold and close coupled catalyst for temperature and flow. Comparing to measured and analyzed result, it find increasing of collector volume effects to catalyst temperature distribution and uniformity of catalytic converter