• 한국분무공학회지
• /
• 제15권2호
• /
• pp.61-66
• /
• 2010

Fuel spray characteristics of the gasoline engine injector has been studied experimentally. To provide fundamental performance data of 4-hole and 12-hole injectors, spray fuel-mass distribution, wall wetting fuel amount and visualization of injectors have been tested and measured with various fuel supply pressure conditions. Spray visualization has been performed to analyze spray formation, spray angle, stream width and penetration length. Test result shows that wall wetting is greatly influenced by the induction air amount and spray atomization. Spray visualization shows that the 12-hole injector has robust performance characteristics with various fuel supply pressure conditions compared with the 4-hole injector. 4-hole injector generates relatively less wall-wetting fuel amount than 12-hole injector does.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.478-483
• /
• 2003

This paper describes spray characteristics of a swirl injector which is intended for use in a HCCI engine. Many optical diagnostics such as laser diffraction methods, and high speed camera photography are applied to measure the spray drop diameter and to investigate the spray development process. The effect of fuel properties on the spray characteristics was investigated using three different fuels because HCCI combustion is tolerant of the chemical composition of various fuels. From these results, the HCCI injector formed a hollow cone sheet spray rather than a liquid jet and the atomization efficiency is high for the low-pressure injector. The SMD of test injector was ranged from $15{\mu}m$ ${\mu}m$ We also found that the spray breakup characteristics were dependent on the fuel properties such as density, viscosity, and surface tension.

• 한국항공우주학회지
• /
• 제34권8호
• /
• pp.79-86
• /
• 2006

액체로켓엔진에서 고주파 연소불안정을 제어하기 위하여 인젝터 길이 변화를 줄 수 있는 백홀 스월 인젝터를 분석하였다. 음향흡수자로서 백홀 인젝터의 효과를 분석하기위하여 백홀 인젝터는 1/4 파장 공명기로 해석하였다. 이론적 접근과 음향 실험의 결과로부터 가변적 변위를 갖는 백홀 스월 인젝터가 연소실의 불안정 모드를 감소시킴을 알 수 있었다. 실험적으로 감쇠율을 측정하여 감쇠효과를 측정하였다.

• 한국자동차공학회논문집
• /
• 제3권6호
• /
• pp.134-144
• /
• 1995

The solenoid actuated hydrogen injector and the capacitive peak-hold type driving circuit were designed and made, and the hydrogen supply system for in-cylinder injection was constructed with these. The performance of the injector was investigated through measuring the pintle lift profiles and the injection quantities, and the performance of the hydrogen supply system was confirmed through the experiments at the single cylinder engine. The injection quantity increased linearly as the duration of driving signal increased. At the single cylinder engine, the hydrogen injector was operated stably. The hydrogen flow rate of the injector with the peak-hold type driving circuit could be controlled precisely at high engine speed or low load condition only with the variation of signal duration.

• 한국자동차공학회논문집
• /
• 제3권6호
• /
• pp.123-133
• /
• 1995

An injection control valve(ICV) was designed to control the fuel flow between a common rail and an injector with two commercial solenoids. To improve the performance of ICV, the characteristic method was applied. With this method, the flow characteristics in the ICV and the injector were studied and the parameters which affect the injection characteristics were also studied. From this study, following results were obtained. The injection duration can be controlled and with modifications of the effective valve stroke of ICV, the injection quantity and duration can be reduced to desired amount. Also the injection quantity and pressure can be controlled by reducing the hole size of the injector without the variation of the injection duration. For some conditions, the desired injection characteristics can be obtained by the changes of the valve timing, the effective valve stroke, the open pressure of the injector and the hole size of the injector.

• 한국분무공학회지
• /
• 제8권2호
• /
• pp.7-15
• /
• 2003

The effects of fuel density and fuel viscosity on spray characteristics were investigated under two different gas turbine fuels and various fuel supply pressure conditions through measurement of SMD, number density and volume flux by using PDPA system in dual orifice injector for gas turbine engines. In this study, we found out that the droplet size and spray structure are strongly depend on fuel density for dual orifice injector. The spray characteristics of high density fuel in dual orifice injector are similar with the characteristics of low density fuel in single orifice injector. The shear region between primary main fuel stream and secondary main fuel stream is examined in low density fuel condition but not exist in high density fuel condition, then this shear region is very important in quality of gas turbine spray. There are worth consideration for the effect of fuel density on spray characteristics in frontal device design to improve combustion efficiency.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권12호
• /
• pp.633-638
• /
• 2001

The paper presents the fabrication and test of a micro scent injector module. A micro scent injector module consists of an injector fabricated by micromachining, a scent cartridge and a controller. If a scent injection signal triggers the controller, it heats the scent liquid in the injector chamber and a scent liquid is vaporized. The increased vapor pressure opens a normally closed boss valve, and the scent vapor is injected through the opened nozzle. The liquid volume injected by the fabricated module is about $1\muell$ for one second at 2 W.

• International Journal of Aeronautical and Space Sciences
• /
• 제12권1호
• /
• pp.57-62
• /
• 2011

The effects of swirl chamber's diameter and length on injector's dynamic characteristics were investigated through an experimental study. A mechanical pulsator was installed in front of the manifold of a swirl injector which produces pressure oscillations in the feed line. Pressure in the manifold, liquid film thickness in the orifice and the pressure in the orifice were measured in order to understand the dynamic characteristic of the simplex swirl injector with varying geometry. A direct pressure measuring method (DPMM) was used to calculate the axial velocity of the propellant in the orifice and the mass flow rate through the orifice. These measured and calculated values were analyzed to observe the amplitude and phase differences between the input value in the manifold and the output values in the orifice. As a result, a phase-amplitude diagram was obtained which exhibits the injector's response to certain pressure fluctuation inputs. The mass flow rate was calculated by the DPMM and measured directly through the actual injection. The effect of mean manifold pressure change was insignificant with the frequency range of manifold pressure oscillation used in this experiment. Mass flow rate was measured with the variation of injector's geometries and amplitude of the mass flow rate was observed with geometry and pulsation frequency variation. It was confirmed that the swirl chamber diameter and length affect an injector's dynamic characteristics. Furthermore, the direction of geometry change for achieving dynamic stability in the injector was suggested.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
• /
• pp.451-454
• /
• 2006

This paper describes the results of cold flow test and hot firing tests of an uni-element coaxial swirl injector and hot firing tests of a subscale combustor, as to the development effort of coaxial swirl injector for high performance liquid rocket engine combustor. A major design parameter for coaxial swirl injector is the recess number of a bi-swirl injector. The results of hot firing tests of the uni-element injector combustor and the sub-scale combustor are analyzed to investigate the effect of the recess number influencing on the combustion performance and pressure fluctuation. The test results of a cold flow test of the unielement combustor shows that it was shown that the change in recess number has significant effect on mixing characteristics and efficiency, while the effect of recess number on atomization characteristic is not The results of a series of firing tests using unielement and subscale combustor show that the recess length significantly affects the hydraulic characteristics, the combustion efficiency, and the dynamics of the liquid oxygen/kerosene bi-swirl injector. As a point of combustion performance, combustion efficiencies are 90% for unielement combustor and 95% for subscale combustor. The difference in the characteristic velocities between the unielement combustor and the subscale combustor may be caused by the difference in thermal loss to the combustor wall and the relative lengths of the combustion chamber. For a mixed type coaxial swirl combustor, the pressure drop across the injector increases as recess number becomes larger. The low frequency pressure fluctuation observed in unielement combustor can be related to the propellant mixing characteristics of the coaxial bi-swirl injector. The effect of the recess number on the pressure fluctuation inside the combustion chamber is more significant in un i-element combustor than the subscale combustor, of which the phenomena are also observed in time domain and frequency domain.

• 한국추진공학회지
• /
• 제20권2호
• /
• pp.39-45
• /
• 2016

동축형 다공성재 분사기에서는 기체가 분사기 중심을 지나는 액체 제트 주위를 둘러싼 다공성재를 통해 액체 제트를 향해 분사된다. 분사 방법의 차이로 인한 전단동축 분사기와 동축형 다공성재 분사기의 분열 메커니즘 차이를 살펴보기 위해, 전단동축 분사기와 동축형 다공성재 분사기를 사용하여 수류시험과 2-D 축대칭 수치해석을 진행하였다. 같은 유량조건에서의 가시화 이미지와 분무 평균입경을 비교하였으며, 수치해석을 통해 분사기 내부에서의 속도 분포가 액체 제트에 어떤 영향을 끼치는지 고찰하였다. 결과적으로, 기체의 유량이 늘어날수록 분사기 내부 속도가 낮음에도 동축형 다공성재 분사기의 미립화 및 혼합 성능이 전단동축 분사기에 비해 유리함을 확인할 수 있었다.