• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.10
• /
• pp.102-109
• /
• 2000

In the present study, gas-assisted molding and structural vibration analysis of hollow long cylinder with the variation of gas injection pressure are performed. Though there are so many parameters such as delay time, injection pressure, and gas pressure on gas-assisted molding, the latter has the most dominant effect on this process. Therefore, the present paper deals with the effects of gas pressure on the dynamic stiffness of the model by means of vibration analysis and then suggests the fundamental materials which can be directly adapted to manufacturing lines.

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.3
• /
• pp.102-108
• /
• 1992

To clarify the structure of a diesel spray, a transient non-evaporating diesel spray injected under different ambient pressure and different injection pressure was studied. Spray tip penet- ration and spray angle were measured by taking the high speed shadowgraph of spray and Sauter mean Diameter(SMD) was also measured by light scattering technique at different positions along the spray axis and at different time from the start of injection. The effects of the operating parameters on the spray shape and SMD were investigated. By increasing the injection pressure, the spray tip penetration and the spray angle increased and the change of the ambient pressure also resulted in the considerable change in the shape of the spray. The analysis of SMD measurement showed that the atomization is a process that continues in sp- ace and time. As the injection pressure increases SMD decreases rapidly and with the increa- se of the ambient pressure the atomization process ends faster than the lower ambient press- ure and at lower pressure the atomization process continues to much farther downstream and far afterward.

• Proceedings of the KSAR Conference
• /
• 2002.06a
• /
• pp.50-50
• /
• 2002

During fertilization, morphological and molecular events in male and female chromatin are precisely controlled in time. However, little information is available on onset of pronuclear formation and first S-phase entry in the pig following intracytoplasmic sperm injection. To assess species specific paternal effect on the pronuclear formation and initiation of first S-phase in the pig, we examined time of onset of male and female pronuclear formation and onset of DNA synthesis in the oocytes following pig or mouse sperm injection. (omitted)

• Journal of Electrochemical Science and Technology
• /
• v.11 no.3
• /
• pp.248-256
• /
• 2020

In this study, pyrocatechol violet (Pcv) is proposed for the first time as an efficient electrocatalyst for oxidation of sulfide and flow injection analysis (FIA) of sulfide. A graphite pencil electrode (GPE) was modified with Pcv via immersion of the GPE into 0.01 M Pcv solution for 15 min. Cyclic voltammograms (CVs) demonstrated that Pcv/GPE exhibits a good electrocatalytic performance due to shift in the potential from +400 at bare GPE to +70 mV at Pcv/GPE and obtaining an enhancement in the peak current compared with the bare GPE. A linear range between 0.25 and 250 μM sulfide with a detection limit of 0.07 μM was obtained from the recorded current-time curves in Flow Injection Analysis (FIA) of sulfide. Sulfide in water samples was also successfully determined using the proposed FI amperometric methods.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.3
• /
• pp.224-229
• /
• 2016

Recently, polymeric micro-fluidic biochips with numerous micro patterns on the surface were fabricated by injection molding for realizing low-cost mass production of devices. To evaluate the effects of process parameters on large-scale micro-structure replication, a $50{\times}50mm^2$ tool insert with surface structures having a patterns of trapezoidal shapes (height: $30{\mu}m$) was employed. During injection molding, PMMA was used; packing phase parameters and mold temperature were investigated. The replicated surface textures were quantitatively characterized by confocal laser microscopy with 10-nm resolution. The degree of replication at low mold temperatures was found to be higher than that at high mold temperature at the beginning of the packing stage. Thereafter, the degree of replication increased to a greater extent at higher mold temperatures; application of higher mold temperatures improved the degree of replication.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.10a
• /
• pp.226-229
• /
• 2008

When methane hydrate is artificially formed to store and transport large quantity of natural gas, its reaction time may be too long and the gas consumption in water becomes relatively low, the reaction rate between water and methane gas is low. Therefore, the present investigation focuses on the rapid production of hydrates and increases the gas consumption by injecting water into methane gas utilizing nozzle. the hydrate in water injection using a nozzle formed rapidly more than that in gas injection, and the gas consumption of methane hydrate in water injection is about three to four times greater than that in gas injection according to subcooling.

• Design & Manufacturing
• /
• v.2 no.3
• /
• pp.6-9
• /
• 2008

This paper describes the process of structure analysis and injection molding analysis to manufacture the forming injection dies for huge glass insert. Factors such as filling time, filling pressure, material temperature, shrinkage, warpage were investigated by using the analysis software, Moldflow. Runner system and cavity structure were designed and manufactured through the results of deformation analysis data for glass insert. Filling time and filling pressure were analyzed in 3.756sec and 43.37MPa.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.293-296
• /
• 2008

Injection molding operation consists of filling, packing, and cooling phase. The highest pressure is involved during the packing phase among the operation phases. Cavity pressure depends upon velocity to pressure switchover time and magnitude of packing pressure. The cavity pressure is directly related to stress concentration in the cavity of mold. Thus the observation and control of cavity pressure is very important to prevent mold cracking. In this study, cavity pressures were observed for operational conditions using the commercial CAE software, Moldflow. Operational conditions were velocity to pressure switchover time and packing pressure. Cavity pressures were also measured directly during injection molding. Simulation and experimental results showed good agreement.

• Corrosion Science and Technology
• /
• v.20 no.3
• /
• pp.143-151
• /
• 2021

In this study, optimal shot peening process conditions were investigated for improving the cavitation erosion resistance of gray cast iron under a marine environment. Shot peening was performed with variables of injection pressure and injection time. The durability was then evaluated through cavitation erosion test which was conducted according to the modified ASTM G-32 standard. The tendency of cavitation erosion damage according to shot peening process condition was investigated through weight loss rate, surface and cross-sectional analysis of the specimen before and after the test. As a result, the shot peening process condition that could minimize cavitation erosion was when the injection pressure was the lowest and when the injection time was the shortest. This was because the flake graphite exposed on the gray cast iron surface could be easily removed under such condition. Therefore, the notch effect can be prevented by surface modification. In addition, the cavitation erosion damage mechanism of gray cast iron was discussed in detail.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.21 no.2
• /
• pp.469-485
• /
• 1994

The present study was undertaken to examine the relationship between time required for each step in the treatment process for pedodontic patients. and age of the patients, and experience of special training for pedodontics and career of dental practitioners. Information of these matters was gained from 580 questionnaires collected from 69 practitioners (62 male and 7 female). The questionnaires included questions about the patients' sex(303 male and 207 female) and age. The patients were categorized into 5 different age groups : Group 1, age $1{\sim}3$-year ; Group 2, $4{\sim}6$-year ; Group 3, $7{\sim}9$-year ; Group 4, $10{\sim}12$-year ; Group 5, $13{\sim}15$-year. The questions about the dental practitioners were the years of experience in private dental practice(5 years or more than 5 years) and whether or not they took the special training for pedodontics in the authorized institutes. The practitioners were asked to answer the questions about Frankl scale of the patients' behavior during the treatment, and time spent for managing the patients to be subjected to local anesthetic injection (the first behavior control), time for the injection, and time for the subsequent treatment. The results obtained by analyzing the information collected from the questionnaires were as follows : 1. The younger the patients, the lower the Frankl scale was counted at the time of the first behavior control, injection, and the subsequent treatment(p<0.001). 2. The lowest Frankl scale was scored during the injection regardless of the age of the patients. 3. Time for management and treatment was decreased in the order of age Groups 1 and 2< Group 3 < Groups 4 and 5. 4. The patients showed a more positive frankl scale in response to the treatment performed by those who were more-experienced in dental practice as compared with those were less-experienced. 5. Pedodontic training experience of the practitioners did not appear to influence the patients with respect to the treatment time and Frankl scale.