• Design & Manufacturing
• /
• v.10 no.3
• /
• pp.8-13
• /
• 2016

Despite technological advance, there have been several troubles in photo reaction injection molding (photo RIM) to produce ultra thin light guide panels (LGPs). In this study, micro leakage problem at cavity edge during photo RIM was investigated numerically. In order to obtain optimal processing conditions, we regulated inlet pressure of injected resin at the cavity edge and figured out micro leakage behaviors. At low inlet pressure (less than 100 Pa), though the micro leakage problem was not occurred, another problem, short shot due to not enough driving force, was appeared More than 1,000 Pa of the inlet pressure, injected resin was rapidly leaked through the micro gap at the cavity edge. Finally, we obtained optimal inlet pressure around 600 ~ 1,000 Pa. At this region, injected resin fully filled the cavity without micro leakage behavior. Based on the present study, further comparative investigations with experimental photo RIM should be performed to find optimal processing conditions for produce ultra thin LGPs.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.26 no.5
• /
• pp.209-214
• /
• 2016

Foam reaction injection molding (FRIM) is a widely used process for manufacturing polyurethane foam with complex shapes. Numerical model for polyurethane foam forming reaction during FRIM process has been intensively investigated by a number of researchers to precisely predict final shapes of polyurethane foams. In this study, we have identified a problem related with a previous theoretical model for polyurethane foam forming reaction. Thus, previous theoretical model was modified based on experimental and computational results.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.6
• /
• pp.1494-1499
• /
• 2008

Plastic materials are utilized to the most important material of automobile interior-parts due to special characteristics that it is light, good strength and do not transmute quality even if pass long time. This study presented a preliminary analysis of fill time, weld line, air trap etc. for the plastic injection molding process of automobile gearbox cover through simulation using Moldflow.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.474-479
• /
• 2005

Experimental and theoretical studies of internal cavity pressure during injection molding of a spiral tube cavity were carried out. The frozen layer thickness and the evolution of internal cavity pressure were calculated using a commercial software (C-MOLD). The evolution of the internal cavity pressure was recorded during injection molding of polystyrene into a spiral tube mold. To explain the differences observed between the calculated and measured internal cavity pressure, a pressure correction factor (PCF) was introduced based on the plane stress theory. This factor was determined by analyzing the stress state in the melt and calculating the frozen layer thickness near the mold wall. The corrected and experimental pressures have been compared to validate the applicability of the pressure correction factor.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.7 no.1
• /
• pp.53-61
• /
• 2008

In this research, the layout and geometry of U-type ribs in the part, including significant process conditions, are automatically optimized to reduce part warpage with robustness in consideration. The optimization procedure are based on an iterative redesign methodology integrated with computer aided injection molding simulation, Taguchi's Design of Experiment(DOE), and a direct search-based optimization method. The robustness of a design alternative is efficiently measured by introducing composite noise factor and Taguchi's signal-to-noise ratio. As a solution search methodology, the modified design space reduction method based on orthogonal arrays is employed to exploit an optimal robust design alternative. To illustrate the proposed methodology, a case study is performed on simulation results, where an optimal robust design alternative is obtained with a moderate number of iterations.

• Transactions of Materials Processing
• /
• v.18 no.2
• /
• pp.122-127
• /
• 2009

The injection mold with multi-cavity is essential for mass production of plastic products. Multi-cavity molds are designed to geometrically balanced runner system to uniformly fill to each cavity. However, despite geometrical balanced runner system, filling imbalances between cavity to cavity have always been observed in injection molding. To solve these problems, many studies such as Melt Flipper, RC Pin, and others have been presented. The results of these studies have been an effect on filling balances in multi-cavity molds. But, those have had a limitation that additional insert parts must have existed in the mold. In this study, a new runner system is suggested for filling balance between cavity to cavity using "Melt-Buffer" with simple change of runner shape. A series of simulation to confirm feasibility of Melt-Buffer's effects was conducted using injection molding CAE program. Also, a series of injection molding experiment was conducted using plastic materials such as ABS and PP. As results of this study, feasibilities of filling balances by Melt-Buffer were confirmed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.06a
• /
• pp.769-770
• /
• 2007

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.2
• /
• pp.216-222
• /
• 2013

This paper deals with the issue of kinematic modeling and analysis of a toggle mechanism. Based on the mathematic model of a conventional five-point type toggle mechanism. New five-point type toggle mechanism has been analyzed by computer simulation method. A sensitivity ratio has been defined and analyzed to compare its performance with four-point type toggle mechanism. A cycloidal motion has been applied to the cross head as an input and the motion of the moving platen is considered as an output. The effect of link design parameter as well as the type of toggle has been investigated by computer simulation to be available for industrial applications of injection molding machines.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.2 no.2
• /
• pp.115-119
• /
• 2001

The design and manufacture of injection molded polymeric parts with desired properties is a costly process dominated by empiricism, including the repeated modification of actual tooling. This paper presents an knowledge-based synthesis system which can predict the mechanical performance of a molded product and diagnose the design before the actual mold is machined. The knowledge-based system synergistically combines a rule-based system with CAE programs. Hueristic know]edge of injection molding. flow simulation, and mechanical performance prediction is formalized as rules of an expert consultation system. The expert system interprets the analytical results of the process simulation, predicts the performance, evaluates the design and generates recommendation for optimal design alternatives.

• Korea-Australia Rheology Journal
• /
• v.12 no.1
• /
• pp.83-92
• /
• 2000

In resin transfer molding (RTM) process, preplaced fiber mat is set up in a mold and thermoset resin is injected into the mold. An important interest in RTM process is to minimize cycle time without sacrificing part quality or increasing cost. In this study, the numerical simulation and optimization process in filling stage were conducted in order to determine the optimum gate locations. Control volume finite element method (CVFEM) was used in this numerical analysis with the coordinate transformation method to analyze the complex 3-dimensional structure. Experiments were performed to monitor the flow front to validate simulation results. The results of numerical simulation predicted well the experimental results with every single, simultaneous and sequential injection procedure. We performed the optimization analysis for the sequential injection procedure to minimize fill time. The complex geometry of an automobile bumper core was chosen. Genetic algorithm was used in order to determine the optimum gate locations with regard to 3-step sequential injection case. These results could provide the information of the optimum gate locations in each injection step and could predict fill time and flow front.