• 소성∙가공
• /
• 제14권7호
• /
• pp.624-627
• /
• 2005

In this paper, we investigated the possibility of replicating patterned media by nano-injection molding process with a metallic nano-stamper. The original nano-master was fabricated by I-beam lithography and ICP etching process. The metallic nano-stamper was fabricated using a nanoimprint lithography and nano-electroforming process. Finally, the nano-patterned substrate was replicated using a nano-injection molding process without additional etching process. The replicated patterns using nano-injection molding process were as small as 50nm in diameter, 150nm in pitch, and 50nm in depth.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.32-36
• /
• 2001

Recently, reaction injection molding has been used broadly for rapid prototyping, because of its convenience and versatility. Since the properties of molded products are dependent on the process variables and the production is very short(less than 2minutes), the control of process variables is important. Generally, the two significant process variables are degree of cure and temperature of the reactants. In this paper, the relation between the degree of cure and the temperature of reactants was investigated to find the optimal curing condition of reaction injection molding for rapid prototyping. The degree of cure during reaction injection molding was measured by the Lacomtech sensor and dielectrometry equipment employing Wheatstone bridge type circuit.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.83-84
• /
• 2006

Due to the capability of net shaping for complex 3D geometry, powder injection molding (PIM) is widely used for automotive parts, electronics and medical industry. In this study, an ultrasonic dental scaler tip produced by machining process was redesigned for the PIM process. An injection mold was designed and manufactured to produce the dental scaler tip by the PIM process.

• 소성∙가공
• /
• 제15권2호
• /
• pp.158-163
• /
• 2006

The demand for the miniaturization and high-precision of machine part has recently increased in new technology like biotechnology(BT) and nanotechnology(NT). The purpose of this study is to analyze the molding characteristics according to injection conditions by measuring the filling height in micro injection molding of the polypropylene(PP) and cyclic olefin copolymer(COC). The result shows that the filling effect of COC is better than that of PP in micro rib structure with injection molding process.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.214-219
• /
• 2005

Pressure distribution in the cavity during injection molding affects part quality. In this study pressure distributions in the runner, near gate in the cavity, and end of ail in the cavity have been measured using direct pressure sensors for various molding conditions. Molding conditions were injection speed, injection pressure, packing time from filing stage, and packing pressure. Through experiments it was realized that the packing time from filling stage and packing pressure are the dominant factors on the part quality such as part shrinkage. Experimental results have been compared with computer simulations.

• 소성∙가공
• /
• 제8권3호
• /
• pp.276-283
• /
• 1999

This study focuses on part quality and cycle times under gas-assisted injection molding (GIM) of box shape molded parts. The position of the gas channel was established near to parting line at the end of last locations to fill. Applied hot runner and valve gates, the gas was introduced directly into the mold cavity via gas pin. As GIM was applied, the conclusion reached as follows. I) The quality of appearance was improved by reducing sink marks and scratches of texture. ii) The reliability was improved by preventing warpages and reinforcing rigidity through optimum gas channel layout. iii) It is enable to use small size of injection molding machine step by step as GIM was accomplished low pressure and reduced clamp forces against CIM. iv) The productivity were improved by reducing cycle times.

• Design & Manufacturing
• /
• 제2권2호
• /
• pp.33-37
• /
• 2008

This paper describes the optimization of injection molding conditions to minimize sink marks. Sink marks, which refer to a small depression on the surface opposite a thick wall thickness, are often encounted in injection molded plastic parts. Part geometry, material properties and processing conditions during injection molding can affect the sink mark depth. We designed the runner system which is possible balanced filling to cavities using CAE program and then obtained optimal processing conditions by Taguchi's Robust Design technique. By actual injection molding using optimized mold and molding conditions, it confirmed that sink mark depth decreased zero compared to 1mm level in the conventional mold and process.

• 한국정밀공학회지
• /
• 제25권7호
• /
• pp.111-115
• /
• 2008

This paper describes the optimization of injection molding conditions to minimize sink marks. Sink marks, which refer to a small depression on the surface opposite a thick wall thickness, are often encounted in injection molded plastic parts. Part geometry, material properties and processing conditions during injection molding can affect the sink mark depth. We designed the runner system which is possible balanced filling to cavities using CAE program $Moldflow^{TM}$ and then obtained optimal processing conditions by Taguchi's Robust Design technique. By actual injection molding using optimized mold and molding conditions, it confirmed that sink mark depth decreased zero compared to 1mm level in the conventional mold and process.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.60-63
• /
• 2005

In this paper, we investigated the possibility of replicating patterned media by nano-injection molding process with a metallic nano-stamper. The original nano-master was fabricated by E-beam lithography and ICP etching process. The metallic nano-stamper was fabricated using a nanoimprint lithography and nano-electroforming process. Finally, the nano-patterned substrate was replicated using a nano-injection molding process without additional etching process. The replicated patterns using nano-injection molding process were as small as 50 nm in diameter, 150 nm in pitch, and 50 nm in depth.

• Design & Manufacturing
• /
• 제13권3호
• /
• pp.29-34
• /
• 2019

Cell phone injection is characterized by its small size and thinness. In addition, the product has a short cycle time, requiring a very short production schedule. To produce more accurate products faster, data from experience in producing similar products is required. In this study, two mobile phone models are presented. In this study, the quality problems caused by molding analysis and actual injection molding were analyzed and made into a database. As a result, it was considered that all the defects in the molding analysis do not affect the product in some cases, rather than appear as defects in the actual product. All defects shown in the molding analysis can be made into a database, and based on this data, it will be possible to obtain an effect that can predict more accurately whether it will cause problems after injection.