• Geomechanics and Engineering
• /
• 제19권6호
• /
• pp.513-522
• /
• 2019

This study presents an elasto-plastic (EP) solution for drained cavity expansion on the basis of unified strength failure criterion and considers the influence of initial stress state. Because of the influence of initial consolidation of soil mass, the initial stress may be anisotropic in the natural soil mass. In addition, the undrained hypothesis is usually used in the calculation of cavity expansion problem, but most of the cases are in the drained situation in practical engineering. Eventually, the published solution and the presented solution are compared to verify the suitability of the study.

• 한국기계가공학회지
• /
• 제15권1호
• /
• pp.122-128
• /
• 2016

The purpose of this study was to develop improved strength of an arm and a boom on over-load environment, which causes damage in the initial design statement. To develop improved strength of an excavator front group, we calculated load conditions using the MATLAB program, and using these conditions, we performed a structural analysis of an excavator front group for the maximum digging force condition. Finally we performed a topology optimization to reduce weights of an arm and a boom, and we re-modeled an arm and a boom based on the topology design results and re-performed the structural analysis. The strength of the re-design is higher than the initial design but its weight is almost the same as the initial design.

• Journal of Welding and Joining
• /
• 제19권3호
• /
• pp.311-316
• /
• 2001

This paper presents that the affecting factors to the solderability and initial reliability. It is the factor that the coefficient of thermal expansion between package and PCB(Printed Circuit Board), the quantity of solder paste and reflow condition, and Au thickness of the solder ball pad on polyimide tape. As the reflow soldering condition for 48 ${\mu}BGA$ is changed, it is estimated that the quantity of Au diffusion at eutectic Sn-Pb solder surface and initial bonding strength of eutectic Sn-Pb solder and lead free solder. It is the result that quantitative measurement of Au diffusion quantity is difficult, but the shear strength of eutectic Sn-Pb solder joint is 842 mN at first reflow and increases 879 mN at third reflow. The major failure mode in solder is judged solder fracture. So, Au diffusion quantity is more affected by reflow temperature than by the reflow times.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 제4회 박판성형 심포지엄
• /
• pp.35-40
• /
• 2003

In order to develope springback control technology for high-strength steel sheets, some studies have been conducted: dome stretching test, stepped s-rail forming and springback measurement, and optimally shaped initial blank design. First, to find out the formability of TRIP60, dome stretching test was performed. Next the stepped s-rail die, which was designed to form a channel type panel with large twist and wall curl, was manufactured and used to know the effect of controlling forming variables, such as blank holding force and flange amount on the springback. Furthermore, new measurement method of the springback was introduced to define wall curl and twist in geometrically complex panels. Finally, the optimally shaped initial blank was employed to verify one of the best ways to control the springback in channel type, high strength sheet panels.

• Geomechanics and Engineering
• /
• 제34권2호
• /
• pp.197-208
• /
• 2023

Rate-dependent mechanical response of sand, subjected to loading of medium to high strain rate range, is of interest for several civilian and military applications. Such rate-dependent response can vary significantly based on the initial density state of the sand, applied confining pressure, considered strain rate range, drainage condition and sand morphology. A numerical study has been carried out employing a recently proposed visco-plastic constitutive model to explore the rate-dependent mechanical behaviour of Toyoura sand under drained triaxial loading condition. The model parameters have been calibrated using the experimental data on Toyoura sand available in published literature. Under strain rates higher than a reference strain rate, the simulation results are found to be in good agreement with the experimentally observed characteristic shearing behaviour of sand, which includes increased shear strength, pronounced post-peak softening and suppressed compression. The rate-dependent response, subjected to intermediate strain rate range, has further been assessed in terms of enhancement of peak shear strength and peak friction angle over varying initial density and confining pressure. The simulation results indicate that the rate-induced strength increase is highest for the dense state and such strength enhancements remain nearly independent of the applied confinement level.

• Journal of Welding and Joining
• /
• 제18권4호
• /
• pp.87-95
• /
• 2000

Residual stresses and deformations due to welding have effects on the strength of structures. In this paper, the compressive strength of basic welded structures is studied and the effects of the residual stresses and deformations on the compressive strength of beams, plates and shells are investigated,. Theoretical analysis for the basic structures is carried out and simplified methods to calculate the compressive strength are proposed. The proposed methods yield simple formulas to calculate the compressive strength, of which results are much helpful. The accuracy of the proposed method is revealed by comparison with experimental results.

• 한국강구조학회 논문집
• /
• 제10권2호통권35호
• /
• pp.153-160
• /
• 1998

각형 강관(${\boxe}-75{\times}75{\times}3.2,\;{\boxe}-100{\times}100{\times}4.2,\;{\boxe}-125{\times}125{\times}6.0$) 기둥의 단면 치수와 초기 변형을 측정하였다. 인장시험, 단주 압축강도 실험, 그리고 세장비 $46{\sim}84$ 사이의 기둥에 대한 압축강도 실험을 수행하였다. 유한요소법에 의한 기둥의 압축 강도를 산출하였다. 단면의 공칭 치수에 대한 측정값의 오차는 무시할 정도이며, 초기변형은 각 단면별로 세장비 100에 해당하는 기둥길이에 대해 초과 확률 2.5% 값이 각각 1/490, 1/1121, 1/1395로 나타났다. 인장시험 결과 강재의 항복강도는 최소 규정 강도보다 30% 이상 높다. 기둥 실험 결과 얻은 각형 강관 기둥의 압축강도는 단주 압축강도를 강재의 항복강도로 간주하고 비교하면 유한요소 해석 결과나 AISC, Eurocode의 강도 곡선과 거의 같거나 약간 높은 값이나, 강재의 최소 규정강도를 기준으로 비교하면 실험 결과가 훨씬 높은 강도를 보이는 것으로 나타났다.

• 콘크리트학회논문집
• /
• 제13권2호
• /
• pp.153-160
• /
• 2001

본 연구에서는 콘크리트 부재에서의 축압축강도에 대한 크기효과를 검토하였다. 이를 위하여 두 가지 대표적인 압축파괴모드 중의 하나인 모드 I 파괴에 대한 실험적 연구를 이중 캔틸레버 보를 이용하여 수행하였다. 각 캔틸레버의 축에 대한 작용하중의 편심거리와 초기 균열길이를 변화시킴에 의하여 콘크리트의 축압축강도에도 크기효과가 존재하는 지의 여부를 확인하였고, 최소자승법을 이용하여 수정된 크기효과법칙의 새로운 실험상수들을 제시하였다. 연구결과로부터 초기 균열이 있는 콘크리트 부재의 축압축강도에도 크기효과가 존재함을 확인하였다. 하중의 편심거리에 있어서는 균열선단에서의 인장과 압축응력의 영향이 매우 중요하며 이 경우에 뚜렷한 크기효과가 나타났다. 즉 균열선단에서 인장응력의 영향이 증가하면 콘크리트의 크기효과는 증가한다. 그러나 초기 균열길이의 경우, 축압축강도의 크기효과에 미치는 영향은 존재하지만 균열길이에 따른 차이는 뚜렷하지 않았는데 이는 고강도 콘크리트 부재의 경우 부재의 세장비 차에도 불구하고 파괴진행영역의 크기가 서로 비슷한데 그 원인이 있는 것으로 판단된다.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1993년도 가을 학술발표회논문집
• /
• pp.68-73
• /
• 1993

The geometrical initial imperfection is generally described that a dome digeresses from ideal shape. In actual domes the mode and amplitude for initial imperfection appear variously and affect buckling-strength sensitively. This study investigates the buckling characteristics of single-layer latticed domes with triangular network subjected to initial imperfection. Additionally, this study is to get the data that are to formulate the general equation taking initial imperfection into consideration.

• EDISON SW 활용 경진대회 논문집
• /
• 제5회(2016년)
• /
• pp.167-174
• /
• 2016

Recently laminated plates like composite materials has been used in a various field to grow the specific strength of the composition. However, delamination area caused by barely visible impact damage has potential risk that it can raise buckling of the delaminated plate. Because it can interrupt compressive behavior of laminated plates and reduce their strength, the whole structure can't be constituted by these materials. Many studies assume that behavior of the delaminated plate which is in lamanated plates equals theoretical buckling but their actual motion doesn't coincide because of initial imperfections of materials like deflection, residual stress, eccentricity and so on. In this paper, we change laminated plates with initial delamination into a beam of rectangular cross section with the initial crack and analyze compressive behavior according to initial imperfections through finite element method(FEM). Consequently analysis results show that behavior of laminated plates involving delamination differs from ideal buckling of the delaminated plate in actual conditions and we can predict its motion through imperfections relationship.