• Journal of the Korean Society of Safety
• /
• v.7 no.3
• /
• pp.66-72
• /
• 1992

An experimental study was carried out to analyse the explosion characteristics of flammable gas-air mixtures. Used flammable gases were hydrogen, methane, acethylene, ethylene and pro-pane, explosion Pressure, explosoin pressure rising rate, and flame propagation velocity were measured experimentaly. The maximum explosion pressure and rising rate of flammmalbe gas air mixtures were appeared at the range of slightly higher concentration than the stoichiometric concentration. Initial pressure before explosion was controlled from 0.6 to 2.0kg/cm absolutly. Explosion pressure was increased with increment of the initial pressure, and the relationship between initial pressure and explosion pressure was Pe = KPi. The effect of vessel size on explosion characteristics was also analysed In this experiment. Explosion pressure was increased with in-creasing the vessel size, otherwise explosion pressure rising rate was decreased. When we locate a dummy material in vessel explosion pressure was decreased with increasing the dummy volume but exlosion pressure rising rate was increased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.5
• /
• pp.718-724
• /
• 2000

A model for depicting the rocket engine combustion process is presented and several experiments near a design point are provided with a FOOF type of unlike impinging injector for a propellant combination of Jet A-1 fuel and liquid-oxygen. The model is based on the assumption that the vaporization is the rate-controlling combustion process. The effects of initial drop size and initial drop velocity are systematically shown and discussed. It is seen that in the midst of considered parameters the change of initial drop size is more sensitive to the performance. The proposed model describes qualitative trends of combustion process well despite of its simplicity.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.1
• /
• pp.138-144
• /
• 1990

In order to understand the probabilistic nature of fatigue crack propagation, not only the calculation of failure probability and parameter sensitivity, but also the clarification of probabilistic nature of various parameters should be executed. Therefore a method to evalute synthetically the effect of each parameter on the distribution of fatigue crack propagation life is required. In this study, the effects of the initial crack size and other paramaters on the distribution of fatigue crack propagation life are discussed according to the appropriate normalization of the life distribution, the validity of this method is also shown. Such an investigation as the present work may be useful to understand the nature of the life distribution and to utilize the probailistic fracture mechanics.

• 대한공업교육학회지
• /
• v.32 no.2
• /
• pp.199-216
• /
• 2007

Stream Control Transmission Protocol(SCTP) is a transport layer protocol to support the data transmission. SCTP is similar to Transmission Control Protocol(TCP) in a variety of aspects. However, several features of SCTP including multi-homing and multi-streaming incur the performance difference from TCP. This paper highlights the data transfer during the initial slow start phase in SCTP congestion control composed of slow start phase and congestion avoidance phase. In order to compare the mean transfer time between SCTP and TCP, we experiment with different performance parameters including bandwidth, round trip time, and data length. By varying data length, we also measure the corresponding initial window size, which is one of factors affecting the mean transfer time. For the experiment, we have written server and client applications by C language using SCTP socket API and have measured the transfer time by ethereal program. We transferred data between client and server using round-robin method. Analysis of these experimental results from the testbed implementation shows that larger initial window size of SCTP than that of TCP brings the reduction in the mean transfer time of SCTP compared with TCP by 15 % on average during the initial slow start phase.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.6
• /
• pp.738-745
• /
• 2014

In this paper, It is performing to the elastic and elasto-plastic large deformation series analysis using a numerical method for the initial deflection effect of the aluminum alloy rectangular plate in the elasto-plastic loading area patch loading size. It is assumed a boundary condition to be a simply supported condition and consider the initial deflection amplitude, aspect ratio. It examined the critical elastic buckling load and post-buckling behaviour of aluminium alloy A6082-T6 rectangular plate. It used a commercial program for the elastic and elasto-plastic deformation series analysis. If the initial deflection amplitude is smaller, the in-plane rigidity with increasing to load is reduced from the start and occurs significantly more increasing the amplitude. More higher the aspect ratio, the initial yield strength is gradually decreased, and the plate thickness thicker and occurs larger than the thin walled plate a reduction ratio of the initial yield strength of the patch loading size as 0.5.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.11
• /
• pp.3952-3958
• /
• 2011

The effect of sintering temperature on the electrochemical property of $LiMn_2O_4$ was investigated. Results showed that the particle size was increased at higher sintering temperatures while the initial capacity was decreased after high temperature sintering. Capacity fading, on the other hand, was suppressed at lower sintering temperatures since the sintering at higher temperatures (${\geq}800^{\circ}C$) increased the Mn ions with a lower oxidation state ($Mn^{+3}$), which induced structural instability during cycling due to dissolution of Mn ions into the electrolyte. In particular, $LiMn_2O_4$ sintered above $830^{\circ}C$ showed severe capacity fading (capacity loss was 38% of initial capacity) by lower coulombic efficiency due to the abnormally increased particle size.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.339-342
• /
• 2005

We present an efficient block-based motion estimation algorithm with motion analysis. The motion analysis determines a size of search pattern and a maximum repeated count of search pattern. In case of large movement in large image, we reduce search points and the local minimum which caused by low performance. The proposed algorithm employs with searching step of 2. The first step determines an initial search point with neighbor block vector and a size of initial search pattern. The second step determines a size of search pattern and a maximum repeated count with motion analysis. We improve motion prediction accuracy while reducing required computational complexity compared to other fast block-based motion estimation algorithms.

• Journal of Powder Materials
• /
• v.7 no.4
• /
• pp.205-211
• /
• 2000

Distribution of $Y_2BaCuO_5$ (211) Particles within $YBa_2Cu_3O_{7-x}/$ (123) grains of melt infiltration processed YBCO oxides was investigated. Processing parameters were a temperature, atmosphere (air and $O_2$) and initial 211 size. The 211 particles were distributed randomly within the 123 grains when the initial 211 size was large, while they made x-like pattern and/or butterfly-like patterns when the 211 size was small. The 211 patterns were more clearly observed in the samples prepared at higher temperatures and under $O_2$ atmosphere. The 211 distribution was explained in terms of the interfacial energy relationship among the solid, particle and melt.

• International Journal of Automotive Technology
• /
• v.3 no.3
• /
• pp.95-99
• /
• 2002

The characteristics of soot vaporization induced by a high-energy Pulsed laser were studied in an ethylene-air laminar flame. A system consisting of two pulsed lasers was used for the experiments. The pulse from the first laser was used to vaporize the soot particles, and the delayed pulse from the second laser was used to measure the residual soot volume fraction. Laser-induced soot vaporization was characterized according to the initial particle size distribution. The results indicated that soot particles could not be completely vaporized simply by introducing a high intensity laser pulse. Residual soot volume fractions present after vaporization appeared to be insensitive to the initial soot particle size distribution. Since the soot vaporization effect is more pronounced in the region of high soot concentrations, this laser-induced soot vaporization technique may be a very useful tool for measuring major species in highly sooting flame.

• Proceedings of the Korean Society of Life Science Conference
• /
• 2002.09a
• /
• pp.9-17
• /
• 2002

Renaturation of Lysozyme by size exclusion chromatography(SEC) to improve yield as well as the initial and final protein concentration has been studied in detail, Although urea decreases the rate of proteins refolding, it can suppress protein aggregation to sustain pathway of correct refolding at high protein concentration, and there existed an optimum urea concentration in renaturation buffer. Lysozyme was successfully refolded from initial protein concentration of up to 100mg/m1 by SEC, the yield was more than 40%. And the refolding of Interferon-${\gamma}$ was further investigated.