• Journal of Korea Foundry Society
• /
• v.13 no.5
• /
• pp.441-449
• /
• 1993

SiC particulate reinforced magnesium matrix composites were fabricated by melt stirring method. The effet of several factors on mechanical properties and the efficiency of melt stirring method from the viewpoint of these properties were investigated. The tensile strength increased and the elongation decreased with decrease of the particle size or the increase of the paticulate volume fraction for pure magnesium matrix and Mg-5%Zn alloy matrix composites. A longer stirring time improved the tensile strength of these composites. The tensile strength of Mg-5%Ca alloy matrix composites which shows no uniform paticulate distribution was a little lower than that of matrix alloy. Rapid solidification rate is preferred for the improved tensile strength of these composites. The pure magnesium matrix and Mg-5%Zn alloy matrix composites have tensile strength of about 400MPa. This value agrees with the tensile strength of some magnesium matrix composites fabricated by liquid infiltration method or powder metallurgy method at the same volume fraction of reinforcements of whisker or particle. Therefore, the melt stirring method which has the advantages of simple process is considered to be efficient in fabricating magnesium matrix composites.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.44 no.2
• /
• pp.67-74
• /
• 2002

The purpose of this study was to investigate the effects of ponding depth treatment on water balance in paddy fields. Three ponding depth treatments, very shallow, shallow, and deep were used. The experimental plots were three 80m $\times$ 8m rectangular plots. Daily values of rainfall amount, ponding depth, irrigation water, drainage water, evapotranspiration, and infiltration were measured in the field. The ponding depth was continuously observed by water level logger during the growing season. The ET was measured by 1-m diameter PVC lysimeters. Irrigation water volume was measured by 75 mm pipe flowmeters and the drainage water volume by 75 mm pipe flowmeters and a recording Parshall flume. The results showed that irrigation water depths were 688.9 mm, 513.6 mm, and 624.4 mm in very shallow, shallow, and deep ponding, respectively. The effective rainfall amounts (effective ratio) were 243.7 mm(48.8%), 344.6 mm(68.9%), and 272.9 mm(54.6%) in very shallow, shallow, and deep ponding, respectively. The three treatments did not show any statistical difference in growth and yields. But the shallow depth treatment showed the largest yield.

• Journal of Industrial Technology
• /
• v.3
• /
• pp.95-101
• /
• 1983

This study aims at the determination of the coefficienties of runoff and infiltration affecting runoff. The rating curve is more available than the peak flood runoff to determine flood control plan of flood control reservoir and the volume of hydroelectric power plant, or to make multipurpose dam. In hydrologic analysis and design, it is necessary to develop relations between precipitation and runoff, possible using some of the factors affecting runoff as parameters. In order to calculate the runoff discharge, the runoff process constituting elements are divided to the surface runoff, the subsurface runoff and the groundwater runoff. By comparing the computed hydrograph with the measured hydrograph, determinned the watershed TANK Model constant Varying the tank model constant for approximating the computed hydrograph to the measured hydrograph.

• The Journal of the Petrological Society of Korea
• /
• v.5 no.1
• /
• pp.21-34
• /
• 1996

Contact-metamorphosed calc-silicate hornfels of the Hwanggangni formation adjacent to Daeyasan granite in Goesan are characterized by the mineral assemblages. tremolite-clinozoisite-alkali feldspar-calcite, diopside-grossular-vesuvianite, and wollastonite-diopside-phlogopite-grossular-vesuvianite, indicating low $X_{CO_2}$ condition during contact metamorphism. Two trends of fluid-rock interactions are recognized; combination of infiltration and buffering in the outer portion of the aureole and fluid-dominated behavior in the most part of the aureole. Modal abundance of diopside produced during metamorphism was measured in order to estimate fluid/rock ratios and permeabilities with the assumption that equivalent volume of fluids estimated from the fluid/rock ratios flow through the rock body. The calculated fluid/rock rations and permeabilities range from 0.6 to 9 and $10^{-19}$ to $10^{-17}$ meabilities in the calc-silicate hosted contact aureoles and expected values during progressive metamorphism by theories.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2002.09a
• /
• pp.386-389
• /
• 2002

It may be necessary to apply a daily fever to operate the municipal solid waste landfill. The daily cover helps to control nuisance factors such as the escape of odors, dusts and airborne emissions, and can control the population of disease vectors. Also it may be reduce the infiltration of rain, decreasing the generation of leachate and the potential for surface water and groundwater contamination. Because of its usual availability and traditional usage as the municipal solid waste landfill, soil remains as the most common daily cover material. However, soil tends to reduce the volume of dumping waste c;3pacity in the landfill, it also reduces a period of using in the landfill. Therefore, it is necessary to research about Alternative Daily Cover Materials (ADCMs) because of the limitation of landfill sites. Recently, The types of ADCMs are classified into geosynthetics, forms, spray-ons, indigenous materials. In this study, the authors have tested the spray type of Alternative Daily Cover(ADC) using by flyash, alum with cement. The development. of ADCMs will be highly effective in terms of prolongation using landfill.

• Biomolecules & Therapeutics
• /
• v.23 no.2
• /
• pp.195-200
• /
• 2015

We tested the hypothesis that micro-computed tomography (micro-CT) analysis provides a better quantitative readout of the therapeutic potential of methotrexate (MTX) for treating collagen-induced arthritis (CIA) in rats and compared to conventional histopathological examination. Rats were divided into three groups: Group 1 (G1) was treated with 0.9% saline, whereas groups 2 (G2) and 3 (G3) were boosted with type II collagen at days 0 and 7. Following the first collagen immunization, rats in G1 and G2 were treated with 0.9% saline and those in G3 were treated with 1.5 mg/kg MTX from day 14 to 28. All rats were sacrificed on day 28, at which point and all hind knee joints were analyzed by micro-CT and histopathological examination. Micro-CT analyses showed that bone volume and trabecular number were significantly decreased in G2 and G3 compared to G1 (p<0.01), as was percent bone volume (p<0.05 and p<0.01, respectively). However, bone surface/bone volume was significantly increased in G2 and G3 compared to G1 (p<0.05 and p<0.01, respectively). Trabecular separation was significantly increased in G3 compared to G1 (p<0.05). Histopathological examination showed that knee joints of rats in G2 and G3 showed severe joint destruction with inflammatory cell infiltration. However, cartilage destruction was slightly reduced in G3 compared to G2. Taken together, these results suggest that MTX treatment reduced cartilage destruction in rats with CIA, and micro-CT analyses made it possible to quantify arthritic bony lesion.

• Journal of Korean Society on Water Environment
• /
• v.34 no.3
• /
• pp.308-315
• /
• 2018

SWMM-LID was calibrated with flow monitoring data in LHI to evaluate runoff after LID application. The flow rate in the B basin was estimated to be 0.94 and 6.15 for O/S and $D_v$, respectively. In the A and C basins, the difference between the observed and simulated data was greater than in the B basin. As a result of runoff reduction efficiency by the application of LID facilities, the change of infiltration increased from 34.6 % to 45.8 % in the entire watershed, and the runoff decreased from 58.8 % to 46.3 %. In the runoff reduction of each LID facility, rain garden E showed the highest effect with 99.9 % and bioretention B showed the lowest effect with 27.5 %. In order to evaluate the efficiency of each LID facility, a comparison is made between the pore volume (V) of the LID and the catchment area (A). The runoff showed a runoff reduction effect of about 70 % above the 0.1 volume/area (V/A) value. As a result of examining the runoff reduction with LID facilities by the LID module of SWMM, a reasonable design is possible by reflecting the appropriate LID volume to drainage area.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.8 no.3
• /
• pp.105-115
• /
• 2008

Urbanization results in increased runoff volume and peak flowrate and shortening in time of concentration, which may cause frequent flooding downstream. There are various types of flow retardation methods including detention ponds, retention ponds, and infiltration ponds. In general, hydrologic models to design the detention pond are classified into planning model and design model. This study is comparing and analyzing of planning model to design the detention pond in urban area. Detention ponds data of Disaster Impact Assessment Report on 22 sites were analyzed to investigate proper planning models in this study. From this research, following conclusions are derived, 1) In case of on-line detention pond, Lee model(1991) is the best planning model and similar to real storage volume. 2) In case of off-line detention pond, Abt and Grigg model is much more proper model compared to other models.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.05b
• /
• pp.1199-1203
• /
• 2005

Combined sewer overflows(CSOs) are themselves a significant source of water pollution. Therefore, the control of urban drainage for CSOs reduction and receiving water quality protection is needed. Examples in combined sewer systems include downstream storage facilities that detain runoff during periods of high flow and allow the detained water to be conveyed by an interceptor sewer to a centralized treatment plant during periods of low flow. The design of such facilities as stormwater detention storage is highly dependant on the temporal variability of storage capacity available(which is influenced by the duration of interevent dry periods) as well as the infiltration capacity of soil and recovery of depression storage. As a result, a contiunous approach is required to adequately size such facilities. This study for the continuous long-term analysis of urban dranage system used analytical Probabilistic model based on derived probability distribution theory. As an alternative to the modeling of urban drainage system for planning or screening level analysis of runoff control alternatives, this model have evolved that offer much ease and flexibility in terms of computation while considering long-term meteorology. This study presented rainfall and runoff characteristics or the subject area using analytical Probabilistic model. Runoff characteristics manifasted the unique characteristics of the subject area with the infiltration capacity of soil and recovery of depression storage and was examined appropriately by sensitivity analysis. This study presented the average annual COSs and number of COSs when the interceptor capacity is in the range 3xDWF(dry weather flow). Also, calculated the average annual mass of pollutant lost in CSOs using Event Mean Concentration. Finally, this study presented a dicision of storage volume for CSOs reduction and water quality protection.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.332-332
• /
• 2010

We have successfully demonstrated the inkjet printing method to create $Al_2O_3$ films withouWe have successfully demonstrated the inkjet printing method to create $Al_2O_3$ films without a high temperature sintering process. In order to remove the coffee ring effect in the ink drop, we have introduced a co-solvent system in order to create Marangoni flow in the ink drop, which leads to the dense packing of ceramic powders on the substrate during inkjet process. The packing density of the Inkjet-printed $Al_2O_3$ films is around 60% (max. 70%) which is very high compared to the value obtained from the same material films by other conventional methods such as film casting, dip coating process, etc. The voids inside the films (which are around 40% of the entire film volume) are filled with the polymer resin (Cyanate ester) by the infiltration process. This resin infiltration is also implemented by the inkjet printing process right after the Ah03 film ink-jetting process. The microstructures of the printed $Al_2O_3$ films are investigated by Scanning Electron Microscope (SEM) to understand the degree of packing density in the printed films. The inkjet-printed $Al_2O_3$ films have been characterized to investigate its thickness and roughness. Quality factor of the printed $Al_2O_3$ film is also measured to be over 300 at 1MHz.