• 한국전자통신학회논문지
• /
• 제19권2호
• /
• pp.445-452
• /
• 2024

본 논문에서는 회전형 관성항법장치의 핵심 기술인 최적 회전 절차를 설계하기 위하여 회전 동작별 항법 오차를 분석하는 내용을 다룬다. 회전형 관성항법장치는 관성측정기를 주기적으로 회전시킴으로써 관성센서 오차가 유발하는 항법 오차가 자체적으로 상쇄되도록 고안되었다. 적절히 연이어진 회전 동작은 최대한의 항법 오차를 상쇄시키며, 이를 최적 회전 절차라고 한다. 본 논문에서는 이러한 최적 회전 절차를 설계하기 위하여 회전형 관성항법장치에서 구현 가능한 회전 동작을 구분하고, 각 회전 동작 시 발생되는 항법 오차에 대해 분석한다. 또한 이를 조합하여 회전 절차를 수행할 때 발생되는 항법 오차의 특성을 분석함으로써 최적 회전 절차를 구성하기 위한 조건을 제시한다.

• 한국군사과학기술학회지
• /
• 제9권4호
• /
• pp.71-80
• /
• 2006

Strapdown Inertial navigation systems consist of an inertial sensor assembly(ISA), electronic modules to process sensor data, and a navigation computer to calculate attitude, velocity and position. In the ISA, most gryoscopes such as RLGs and FOGs, have digital output, but typical accelerometers use current as an analog output. For a high precision inertial navigation system, sufficient stability and resolution of the accelerometer board converting the analog accelerometer output into digital data needs to be guaranteed. To achieve this precision, the asymmetric error and A/D reset scale error of the accelerometer board must be properly compensated. If the relation between the acceleration error and the errors of boards are exactly known, the compensation and estimation techniques for the errors may be well developed. However, the A/D Reset scale error consists of a pulse-train type term with a period inversely proportional to an input acceleration additional to a proportional term, which makes it difficult to estimate. In this paper, the effects on the acceleration output for auto-pilot situations and the effects of A/D reset scale errors during horizontal alignment are qualitatively analyzed. The result can be applied to the development of the real-time compensation technique for A/D reset scale error and the derivation of the design parameters for accelerometer board.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.1095-1098
• /
• 1996

In this work, attitude determination with Inertial Reference Unit as attitude sensor is considered. Usually, the attitude error from IRU increases because of gyro rate bias and noise. Therefore, other attitude sensors(sun sensor, horizon sensor, star tracker) are needed to compensate for error from IRU. In this paper, we use the extended Kalman filter for attitude estimation of spacecraft with IRU and star tracker.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2002년도 ICCAS
• /
• pp.32.4-32
• /
• 2002

We consider inertial navigation system (INS) sensor redundancy and propose a method which uses singular value decomposition to detect and isolate faults when even two sensors have faults simultaneously. When redundant sensor configuration is given, such as symmetric configuration in INS, the range space and null space of configuration matrix are determined. We use null space of configuration matrix and define 21 reference fault vectors which include 6 one-fault vectors and 15 two-fault vectors. Measurements are projected into null space of measurement matrix and compared with 21 normalized reference fault vectors, which determines fault detection and isolation.

• 제어로봇시스템학회논문지
• /
• 제19권3호
• /
• pp.190-194
• /
• 2013

This paper presents experimental results of the attitude control for a two-rotor system with 3-DOF(degree-of-freedom). Two DC motors are equipped at the two ends of a rectangular beam to generate lift force and the relation between motor voltage and lift force is found experimentally. And inertial sensors are mounted at the center of the beam to measure the roll angle and a complementary filter is designed to get the angle during DC motors driving. A controller with nonlinear compensation, integrator and state feedback to achieve asymptotic tracking for a step input and reject input disturbance is designed and experimented.

• International Journal of Aeronautical and Space Sciences
• /
• 제11권3호
• /
• pp.234-239
• /
• 2010

The utilization of micro-electro-mechanical system (MEMS) gyros and accelerometers in low-level inertial measurement unit (IMU) influences cost effectiveness in a positive way under the condition that device error characteristics are fully calibrated. The conventional calibration process utilizes a rate table; however, this paper proposes a new method for achieving reference calibration data from the natural motion of pendulum to which the IMU undergoing calibration is attached. This concept was validated with experimental data. The pendulum angle measurements correlate extremely well with the solutions acquired from the pendulum equation of motion. The calibration data were computed using the regression method. The whole process was validated by comparing the measurement from the 6 sensor components with the measurements reconstructed using the identified calibration data.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.856-859
• /
• 1996

In this paper, a coarse alignment algorithm for strapdown inertial navigation system is proposed and evaluated analytically. The algorithm computes roll and pitch angles of the vehicle using accelerometer outputs, and then determines yaw angle with gyro outputs. It is referred, as two-step coarse alignment in this work. With the geometric relation between sensor outputs and roll, pitch and yaw angles, the algorithm error is analytically derived and compared with the previous coarse alignment algorithm introduced by Britting. The results show that the proposed two-step coarse alignment algorithm has better performance for pitch angle computation.

• International Journal of Aeronautical and Space Sciences
• /
• 제12권4호
• /
• pp.371-378
• /
• 2011

In this paper, the wavelet denoising techniques using thresholding method are applied to the low cost micro electromechanical system (MEMS)-global positioning system(GPS) integrated system. This was done to improve the navigation performance. The low cost MEMS signals can be distorted with conventional pre-filtering method such as low-pass filtering method. However, wavelet denoising techniques using thresholding method do not distort the rapidly-changing signals. They can reduce the signal noise. This paper verified the improvement of the navigation performance compared to the conventional pre-filtering by simulation and experiment.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.120-122
• /
• 2004

Wearable input device that can make free-space typewriting possible is introduced. We named this device as $SCURRY^{TM}$. To measure the angular velocity of hand and the acceleration rates at the ends of fingers, we buried MEMS inertial sensors in this keyboard. We processed sensor signals to get the information on hand movement and finger-click motion. With this signal processing, apparent finger movements were depicted over the virtual keyboard shown on output device of a target computing system. In this paper, a finger-click recognition method is proposed to improve the recognition performance for finger clicking of $SCURRY^{TM}$. The proposed method is composed of three parts including feature extraction part, valid click part, and cross-talk avoidance part. The experiments were conducted to verify the effectiveness and efficiency of the proposed algorithms.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.51-55
• /
• 1997

This study is devote to developing navigation filter for detecting sensor failure in multi-sensor navigation system. In multi-sensor navigation system, Kalman filter is generally used to fuse data of each sensors. Sensor failure is fatal in case that the sensor is used as external measurement of Kalman filter therefore detection and recovery of sensor failure is one the important feature of navigation filter. Generally each sensors have its specific feature in measuring navigational information. Fuzzy theory is proposed to detect external sensor failure and provide valid external measurement to Kalman filter avoiding filter divergence and instability. This idea is applied to Autonomous Underwater Vehicle(AUV) which has two navigation sensor i. e self contained inertial sensor and acoustic external sensor. 2 dimensional simulation result shows acceptable failure detection and recovery