• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2010.04a
• /
• pp.195-206
• /
• 2010

Xylan can be applied to improve the strength properties of paper; however the optical properties, such as brightness, are decreased significantly. To solve that problem, an applicable bleaching process is therefore desired. The aim of this research was to investigate the impact of hydrogen peroxide bleaching on hardwood kraft pulp pretreated with birchwood xylan by measuring optical properties (whiteness, brightness, opacity) as well as physical properties (tensile index, tearing index, bulk) of handsheets made from the bleached pulp. Hydrogen peroxide bleaching, as a kind of totally chlorine free (TCF) bleaching method, is quite important industrially for chemical pulp. In our work, the process variables of peroxide bleaching including bleaching temperature, time, initial pH and $MgSO_4$ dosage were studied. The results showed that both good mechanical properties and optical properties could be achieved when the operating parameters were controlled properly and therefore hydrogen peroxide bleaching was proved to be a suitable method for bleaching hardwood kraft pulp with adsorption of birchwood xylan.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.37 no.2 s.110
• /
• pp.21-29
• /
• 2005

Increase in the utilization rate of recycled paper has significantly increased the problem associated with stickies. Despite the effort to eliminate contaminants from recycled furnishes, stickies are still the most serious obstacle in using recycled paper. The amount of micro stickies that are too small to be eliminated by screening, tends to increase significantly as the closure level of white water system is increased and the quality of raw material deteriorates. To establish a process efficient in removing micro stickies is strongly required. In this study, the surface characteristic of micro stickies was investigated with contact angle measurement. Surface energies of MCC, PSA film and model micro stickies were 53.37 mN/m, 29.75mN/m, and 29.63mN/m, respectively. This indicates that the surface characteristic of MMS is very similar to PSA. Thus, solvent coating of PSA and evaporation of the solvent provided excellent model micro stickies for flotation experiment.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.39 no.4
• /
• pp.1-6
• /
• 2007

Paper is a composite consisted of various solid materials including pulp, filler and other additives. The pore is also one of components consisting the paper structure. Thus the characterization of pore structure of paper is very helpful in the understanding the structural properties of paper. Mercury intrusion technique is frequently used for the characterization of the porous paper, giving access to parameters such as pore size and pore distribution. But some researchers pointed out the problem that the distortion of the pore structure can be occurred by the application of high pressure during mercury intrusion. Thus in this study, we tried to evaluate the potential of SEM and image analysis method as means for analyzing pore structure of the paper. The new pore analysis technique with SEM and image analysis does not require the application of high pressure, and gave better relation between the measured pore characteristics and the bulk of sheet than mercury intrusion method.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.365-372
• /
• 2006

In this paper, the possibility of statistical modeling from the pulp and peroxide bleaching condition variables to predict optical properties of a bleached chemimechanical pulp used in a newsprint paper machine at Mazandaran Wood and Paper Industries Company (MWPI) was studied. Due to the variations in the opacity and the brightness of the bleached pulp at MWPI and to tackle this problem, it was decided to study the possibility of modeling the bleaching process. To achieve this purpose, Multi-variate Regression Analysis was used for model building and it was found that there is a relationship between independent variables and pulp brightness as well as pulp opacity, consequently, two models were constructed. Then, model validation was carried out using new data set in the bleaching plant at MWPI to test model predictive ability and its performance.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.11a
• /
• pp.17-27
• /
• 2006

Paper could be situated in a cooled environment seasonally or regionally otherwise it is forced to be in a controlled circumstance. In this paper, printing problems on a cooled paper are investigated and characterized in terms of paper properties. For this purposes, various kinds of sample are cooled down under a specially designed freezing device and printed for observing their printability. Causes for poor ink transfer on a cooled paper are suggested due to condensation, surface inactivity, and rheological change in ink film. Paperboards with higher amount of binder, thick and/or multi coat layers are more vulnerable to poor ink trap. Severe drying could cause the same effect as that of higher binder formulation. It is shown that more absorptive porous structure is desirable for better ink receptivity in a cooled status. Printing on a dampened surface may be an indicator for ink transferability on a cooled paper. Finally, desirable directions for papermaker and printshop are suggested.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.6
• /
• pp.57-65
• /
• 2015

Microfibrillated cellulose (MFC) or Nanofibrillated cellulose (NFC) has been used to reduce the use of raw pulp and to improve paper strength. The problem of MFC preparation is high manufacturing cost. In this study, it was carried out to prepare MFC after enzyme beating and estimated properties of MFC. Endo-D was the best beating efficiency among three type of endo-glucanase. As the grinder pass number increased, the viscosity and the fines of MFC suspension increased while the crystallinity and the porosity of MFC sheet decreased. Also enzyme beating MFC was higher value in the crystallinity and lower value in the viscosity than non-enzyme MFC. In addition, the aspect ratio of MFC was the highest at 5 pass. MFC addition improved the handsheet strength and the air permeability but worsened the drainage.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.39 no.1 s.119
• /
• pp.25-29
• /
• 2007

Print mottle is the spotty and cloudy appearance of the ink on the substrate. Print mottle is influenced significantly by the characteristics of the paper with regard to homogeneity of its structure and its coating. The print mottle can be counteracted, in particular by altering the absorption characteristics of the inks, by changing sequence in which the inks are printed, or by using a advanced coated paper. In this study, we investigated the effect of ink dispersion to the print mottle through trial printing test and also analyzed the correlation between properties of coated paper and subjective results by statistic method. The result of this study is expected to be applied the basic data to solve the problem of printing mottle.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.489-494
• /
• 2006

The strain distribution in the vicinity of a hole in a tensile strip was measured using an image correlation method. The objective of this study is to evaluate the capability of predicting the strain component response using a constitutive model that was developed for use with paper materials. The need for a special constitutive model for paper derives from the characteristics of pronounced anisotropy and the fact that the material behaves differently under compressive loading than it does under tensile loading. The results of the simulation showed that predictions of strain distribution around the hole were in agreement with the experimental result trends, however, the agreement deteriorated as the edge of the hole was reached. It was observed that there is extensive inelastic strain that takes place around the hole prior to failure of the tensile strip. The simulation results showed that any difference between tensile and compressive behavior that may exist for paper material does not have any significant effect for the problem of this study because the level of compressive stress is quite low in comparison with compressive failure values.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.134-139
• /
• 2002

Motorcycle industry, for its competitive position, depends on part design technology. This part design has a bulky amount of data and asks the accumulation of advanced technical skill and experience, and fragmentary technical application is not enough to get to the kernel of a problem. Therefore, the improvement of proper productivity - the starting point of engineering design - and useful Design Methodology for products manufacturing are needed. Thus this paper is aimed to create a program that outputs dynamic characteristics of a vehicle when the data from fully understanding on motorcycle's brake system and induced formula for brake design are inputted.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.1
• /
• pp.101-110
• /
• 2003

Motorcycle industry, for its competitive position, depends on part design technology. This part design has a bulky amount of data and asks the accumulation of advanced technical skill and experience, and fragmentary technical application is not enough to get to the kernel of a problem. Therefore, the improvement of proper productivity - the starting point of engineering design - and useful Design Methodology for products manufacturing are needed. Thus this paper is aimed to create a program that outputs dynamic characteristics of a vehicle when the data from fully understanding on motorcycle's brake system and induced formula for brake design are inputted. This paper is intended to show a creative design method by the thermal analysis data through FEM study and using shape design parameters derived from our programs.