• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 A
• /
• pp.418-420
• /
• 2003

The fault current limiting characteristics at the initial fault time for flux-lock type high-Tc superconducting fault current limiter(SFCL) were investigated. The amplitude of initial fault current of the flux-lock type SFCL was dependent on the inductance ratio of coil 1 and 2. After fault current limiting mode was analyzed, we compared the calculated value with the experimental one for the initial fault current. The effect of initial fault current due to the inductance ratio of coil 1 and 2 on fault current limiting characteristics was discussed.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2014년도 전력전자학술대회 논문집
• /
• pp.329-330
• /
• 2014

This paper presents an analysis of the interleaved effects for the secondary winding distribution of a toroidal transformer. The equations to calculate the leakage inductance are derived using the MMF diagram for the distributed secondary windings. The simulation and experimental results are provided to show the effect of the leakage inductance reduction.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2003년도 종합학술발표회 논문집 Vol.13 No.1
• /
• pp.163-167
• /
• 2003

In this paper, an air-suspension type RF MEMS inductor is fabricated, and an appropriate de-embedding scheme for 3-dimenstional MEMS structure is applied and verified with inductance calculation algorithm. With the presented de-embedding method, parasitics from contanct pads and feeding lines are effectively and accurately de-embedded using open and short calibration procedure, and only spiral and posts can be characterized as a high-Q inductor structure. The validity of the de-embedding method is verified by the comparison of the measured and calculated inductances of two 1.5 and 2.5 turn square spiral inductors. The open-short de-embedded inductance error is below 5% each case in comparison with the calculated value based on H.M. Greenhouse's algorithm.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 추계학술대회 논문집 학회본부
• /
• pp.6-9
• /
• 1997

The study is analyzed the thrust fon:e of moving type Linear DC Motor(MM-LDM). The MM-LDM consists of a stator (platen) and mover (forcer). One of the method for calculating tile thrust of an MM-LDM is to analyze the energy gradient which is determined by the distribution of magnet flux. However, this method is very difficult when used to calculate the thrust force of this kind of LDM. The stored energy in the MM-LDM can be obtained by measuring the self-inductance and mutual-inductance of equivalent circuit of the MM-LOM and this energy gradient gives the thrust. The calculation of thrust force included in this motor shows that the mutual inductance has large influence on the generation of thrust force.

• 한국전기전자재료학회논문지
• /
• 제16권1호
• /
• pp.83-87
• /
• 2003

In the present paper we suggested a parallel branch structure of aluminum spiral inductor for the use of RF integrated circuit at 1∼3 GHz. The inductor was implemented on p-type silicon wafer (5∼15Ω-cm) under the standard CMOS process and it showed a enhanced qualify(Q) factor by more than 10 % with no degradation of inductance. The effect of the structure modification on the Q factor and the inductance was scrutinized comparing with conventional spital inductors

• 반도체디스플레이기술학회지
• /
• 제21권2호
• /
• pp.95-100
• /
• 2022

In this paper, a power loss analysis technique of a high-frequency transformer of a bidirectional DAB (Dual Active Bridge) converter is reported. To miniaturize the transformer of the dual active bridge converter, a resonant inductor was designed with an air gap included low-coupled rate state core to combine leakage inductor with the resonant inductor which is required for soft-switching. In this paper, leakage inductance and magnetizing inductance, core material, type of winding and winding method are included in the dual active bridge transformer loss analysis process to enable optimal design at the initial design stage. Transformer loss analysis for dual active bridge with a switching frequency of 200 kHz and maximum output of 5 kW was executed, and elements necessary for design based on the number of turns on the primary side were graphed while maintaining the transformer turns ratio and window area. In particular, it was possible to determine the optimal number of turns and thickness of the transformer, and ultimately, the total loss of the transformer could be estimated.

• 한국산학기술학회논문지
• /
• 제8권3호
• /
• pp.454-459
• /
• 2007

본 논문에서는 비정질 $Al_2O_3$ 코아 재료를 응용한 단순 solenoid 형태의 소형 고성능 RF 칩 인덕터를 연구하였다. 인덕터 크기는 $0.86{\times}0.46{\times}0.45mm^3$이고, $27{\mu}m$ 직경의 Cu를 코일로 사용하였다. RF 칩 인덕터의 인덕턴스(L), 양호 인자(Q), 임피던스(Z), 커패시턴스(C)와 등가회로 파라미터 등의 주파수 특성은 RF impedance/Material Analyzer (HP16193A test fixture가 장착된 HP4291B)로 측정되었다. $9{\sim}12$회의 권선수를 가진 RF 칩 인덕터들의 인덕턴스 값은 $21{\sim}34nH$ 범위를 가진다. 이들의 자기공진주파수(SRF)는 $5.7{\sim}3.7GHz$ 영역을 나타낸다. 또한 자기공진주파수가 증가함에 따라 인덕턴스 값이 감소하는 경향을 보이고 있다. 인덕터의 SRF는 인덕턴스가 증가함에 따라 감소하며, Q의 값은 $900MHz{\sim}1.7GHz$ 주파수 범위에서 최대 $38{\sim}49$까지 얻어졌다.

• 한국정보전자통신기술학회논문지
• /
• 제12권2호
• /
• pp.142-149
• /
• 2019

전기자동차를 무선으로 충전하기 위하여서는 전기에너지를 전송하기 위한 코일이 꼭 필요하다. 코일의 형태는 기본적인 원형 코일에서부터 두 코일 간의 커플링 효과를 높이기 위한 DD 형상의 코일 등 여러 종류가 있다. 하지만 코일 간 커플링이 좋은 DD 형상의 코일은 송수신 측 전력변환장치의 구조가 복잡해지는 단점이 있어 사용에 제한이 있다. 본 논문에서는 자유공간에서 2개의 코일을 이용하여 무선으로 전력을 전송할 때 제작이 편리한 스파이럴 인덕터의 인덕턴스 값을 계산하고 적절한 크기의 인턱터를 설계하는 방법을 제시하였다. 공진기에서 XLm 값이 부하저항 값과 비슷하여질 때 bifurcation 현상이 나타나므로, 이 현상이 덜 일어나도록 XLm 값을 최소부하저항 값과 같도록 선택하여 공진기에 필요한 인덕턴스 값을 계산하였다. 계산된 인덕턴스 값을 스파이럴 인덕터로 구현하기 위하여 스파이럴 인덕터에서 인덕턴스 값과 인턱터의 크기, 턴 수, 총 코일 길이와의 관계를 알아보았다. 또한, 두 개의 코일의 수평 이격에 따른 결합계수 k 값의 변화를 알아본 후 적절한 인덕터를 선정하였다.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2006년도 High Temperature Superconductivity Vol.XVI
• /
• pp.80-80
• /
• 2006

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2004년도 High Temperature Superconductivity Vol.XIV
• /
• pp.58-58
• /
• 2004