• 한국기계기술학회지
• /
• 제13권2호
• /
• pp.71-78
• /
• 2011

A kart is a vehicle without the suspension system and the differential gear. The kart frame as an elastic body plays the role of a spring. By the cornering of a kart, rolling, pitching and twisting motions are induced in the kart frame. Also the slip or noncontact of the wheel and a permanent deformation of the kart frame can be induced. In order to examine closely this phenomenon, measurement on height-displacements with various sensors and tracking system and analysis on the kart frame twisting characteristics with the rolling and pitching angle are needed. According to the measurement result, while driving in a curve at high speed the kart frame is quite twisted. Analysis on the measurement results shows that a kart used primarily in high speed requires a frame with low torsional stiffness and a frame material with high tensile strength and large elongation.

• Wind and Structures
• /
• 제6권2호
• /
• pp.127-140
• /
• 2003

An investigation into the effect of corner cuts on the Strouhal number of rectangular cylinders with various dimensional ratios and various angles of attack is described. The Strouhal number given as a function of corner cut size is obtained directly from the aerodynamic behavior of the body in a uniform flow through a series of wind-induced vibration tests. For a quick verification of the validity of the Strouhal numbers obtained in this way, they are compared with the approximated the Strouhal numbers based on Shiraishi's early research. The test results show that the Strouhal number of the model with various corner cuts has a fluctuating trend as the angle of attack changes. For each cutting ratio as the angle of attack increases at each cutting ratio above $15^{\circ}$, the Strouhal number decreases gradually, and these trends are more evident for larger corner cut sizes. However, a certain corner cut size which is effective in reducing the wind-induced vibration can be identified by larger Strouhal numbers than those of other corner cut sizes. Three distinct characteristics of Strouhal number variation can be identified in three regions which are termed as Region I, II, and III based on the general trend of the test results. It is also found that the corner cut is effective in one region (Region-II) and less effective in another one (Region-III) when only the vortex-induced vibration occurs.

• Tribology and Lubricants
• /
• 제27권1호
• /
• pp.34-39
• /
• 2011

In this study, finite element analysis of particle-surface collision using 2-dimensional elements was performed to observe the effects of abrasive size and impact angle. The result of the simulation on the change in abrasive size revealed that larger abrasive particle induced larger contact stress due to force transfer through slurry fluid as the particle moved and pushed the fluid. This observation brought an important finding that the slurry fluid could make the workpiece surface soften and then change the mechanical properties of the surface layer such as elastic modulus and yield strength. As for the impact angle, it was found that the contact stress increased with the angle of impact and jumped up at a specific angle. Such result would be attributed to the complex effects of the impact velocity and angle.

• Clinical and Experimental Reproductive Medicine
• /
• 제16권1호
• /
• pp.107-112
• /
• 1989

In order to compare the nocturnal penile erection and the erection induced by intracavernosal injection of papaverine, digital palpation of penis, erectile angle, and the rigigram using $Rigiscan^{(R)}$ were evaluated in 38 erectile dysfunction patients(13 psychogenic, 18 vasculogenic, 1 neurogenic, 3 vasculo-neurcgenic, and 3 undetermined). The following results were obtained. 1. Among the 32 patients of the nocturnal penile erection > 40% on rigigram, only 15 patients(46.9 %) demonstrated rigidity > 4+, a sufficient rigidity for sexual intercourse, on papaverine test. 2. The maximal degree of rigidity was also measured by the erectile angle of the penis. Among the 32 patients of nocturnal penile erection > 40% on rigigram, 23 patients(71.9%) had an angle > $45^{\circ}$. 3. Sixteen patients(42.1%) demonstrated similar increase in the maximal circumferential expansion of the distal portion of the penis on nocturnal penile erection and papaverine-induced erection. Nineteen patients showed larger circumferential expansion on nocturnal penile erection than on papaverine-induced erection. Fifteen patients showed similar circumferential increase of the basal portion of the penis on nocturnal penile erection and artificial erection, while 12 patients(31.6 %) showed larger circumferential increase on artificial erection than on nocturnal penile erection. 4. In the 15 patients of nocturnal penile erection > 40 % on rigigram and > 4+ on papaverine test, the duration of maintenance of the maximum erection on nocturnal penile erection and artificial erection proved to be not proportional. Thus, the arthficial erection induced by papaverine and the nocturnal penile erection can not to be said to be of same in nature and therefore, in order to make more definite diagnosis, both tests should be done and compared.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 춘계학술발표대회 논문집
• /
• pp.235-239
• /
• 2005

In this research, we investigated the frequency characteristic of low-velocity impact induced damage signals on graphite/epoxy composite laminates using high-speed fiber Bragg grating(FBG) sensor system. Appling the FBG sensors to damage assessment, we need to study the response of FBG sensors as the damage signals of the different incident angles because FBG shows different directional sensitivity. In order to discriminate an impact induced damage signal from that of undamaged case, drop impacts with different energies were applied to the composite panel with different incident angle to the FBG sensor. Finally, detected impact signals were compared using frequency distributions of wavelet detail components in order to find distinctive signal characteristics of composites delamination.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.303-310
• /
• 2002

The bending vibration and thermal flutter instability of spacecraft booms modeled as circular thin-walled beams of closed cross-section and subjected to thermal radiation loading is investigated in this paper. Thermally induced vibration response characteristics of a composite thin walled beam exhibiting the circumferantially uniform system(CUS) configuration are exploited in connection with the structural flapwise bending-lagwise bending coupling resulting from directional properties of fiber reinforced composite materials and from ply stacking sequence. The numerical simulations display deflection time-history as a function of the ply-angle of fibers of the composite materials, damping factor, incident angle of solar heat flux, as well as the boundary of the thermal flutter instability domain. The adaptive control are provided by a system of piezoelectric devices whose sensing and actuating functions are combined and that an bonded or embedded into the host structure.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.640-643
• /
• 2006

In this paper, electro-mechanical coupling of cellulose-based Electro-Active Paper (EAPap) actuator is investigated by measuring induced strain and mechanical properties with and without electric excitation. The maximum induced in-plane strain is measured at the orientation angle of 45? samples. The elastic modulus and strength of EAPap are increased with electric excitation and the orientation angle of $45^{\circ}$ samples shows the largest increment of mechanical properties. From the observations, shear piezoelectricity is considered as the major piezoelectric mode of EAPap.

• 대한기계학회논문집A
• /
• 제30권9호
• /
• pp.1134-1141
• /
• 2006

This paper presents the model for evaluating restraint effect of pressure induced bending (PIB) on the circumferential through-wall crack opening displacement (COD), which considers plastic behavior of crack. This study performed three-dimensional elastic-plastic finite element (FE) analyses for different crack angle, restraint length, pipe geometry, stress level, and material conditions, and evaluated the influence of each parameter on the PIB restraint effect on COD. Based on these evaluations and additional perfectly-plastic FE analyses, a closed-form model to evaluate the restraint effect of PIB on the plastic crack opening of circumferential through-wall crack, was proposed as functions of crack angle, restraint length, radius to thickness ratio, axial stress corresponding to an internal pressure, and normalized COD evaluated from linear-elastic crack opening condition.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.383-388
• /
• 2001

Effects of particle property variation of cone crack shape according to impact velocity in silicon carbide materials were investigated. The damage induced by spherical impact having different material and size was different according to materials. The size of ring cracks induced on the surface of specimen increased with increase of impact velocity within elastic contact conditions. The impact of steel particle produced larger ring cracks than that of SiC particle. In case of high impact velocity, the impact of SiC particle produced radial cracks by the elastic-plastic deformation at impact regions. Also percussion cone was formed from the back surface of specimen when particle size become large and its impact velocity exceeded a critical value. Increasing impact velocity, zenithal angle of cone cracks in SiC material was linearly decreasing not effect of impact particle size. An empirical equation, $\theta=\theta_{st}-\upsilon_p(180-\theta_{st})(\rho_p/\rho_s)^{1/2}/415$, was obtained from the test data as a function of quasi-static zenithal angle of cone crack($\theta_{st}$), the density of impact particle(${\rho}_p$) and specimen(${\rho}_s$). Applying this equation to the another materials, the variation of zenithal angle of cone crack could be predicted from the particle impact velocity.

• 한국전기전자재료학회논문지
• /
• 제13권2호
• /
• pp.151-156
• /
• 2000

Effects of alignment layers on pretilt nagle generation and electrical characteristics in nematic liquid crystal(NLC) by using photo-alignment techniques on polyimide PI) surface with side chain were studied. The generated pretilt angle of the NLC on rubbed PI surface with 1-layer is almost the same as that with the 2-layers. However, the generated pretilt angle of the NLC on photo-induced PI surface with 2-layers is larger than that with the 1-layer. The different mechanism of pretilt generation in NLC was observed on the rubbing and photo-alignment method. Therefore, the pretilt angle of the NLC on photo-induced PI surface is attributed to surface roughness due to photo-dissociation on the polymer with UV light irradiation on PI surface. We observed the same characteristics of voltage-transmittance (V-T) and response time for 1- and 2-layers on PI surface. Consequently, we sugest that the VHR of photo-aligned TN-LCD is higher than that of the rubbing-aligned TN-LCD.