• 대한치과보철학회지
• /
• 제42권1호
• /
• pp.11-20
• /
• 2004

Problem : The several studies were reported to the effects of individual tooth tray with the parallel tooth, but not reported to the effect of individual tooth tray with severe undercut in impression making. Purpose : The purpose of this study is to examine the effect of individual tooth tray; 1) the accuracy of impression in terms of distance. 2) reproducibility of pocket. Material and methods : In this study, a metal model with 3 teeth including tooth prepared 30-degree undercut and gingival crevice of the depth 5mm, width 0.4mm was cast. Impressions of the metal model were taken in 5 times used 4 kinds of impression materials with individual tooth tray and another impression taking were made with conventional method without individual tooth, used same materials, procedure. The stone models were made. Distances between abutments were measured with a Micromeasurescoup-mm. Result : The following results were obtained ; 1. In the comparisonof inter-abutment distance between parallel tooth without individual tooth tray, 4elastomeric materials have not significant difference to the metal model(p>0.05). 2. In the comparisonof inter-abutment distance with undercut tooth without individual tooth tray, 4elastomeric materials have a significant difference to the metal model(p<0.05), especially polyether's dimensional change is large. 3. If individual tooth tray was used to take impression in abutment teeth with severe undercut, more stable results was achieved easily than conventional method. (p>0.05). 4. It is not true that the pressure of impression material with individual tooth tray increased to gingival sulcus. Conclusion : By the results, I knew the fact that individual tooth tray was useful impression method on the teeth with severe undercut for the dimensional stability. Also, I could not confirm the fact that individual tooth tray would increase the penetrating pressure into cervice.

• 대한치과보철학회지
• /
• 제37권5호
• /
• pp.567-580
• /
• 1999

Accurate reproduction of intraoral tissue is essential in the fabrication of fixed prosthesis. This selection of impression material and method is very important. In this study, vinyl polysiloxane type impression material $Panasil^{(R)}$ was used. Three impression methods ; one-step technique, individual tray technique, and individual tooth tray technique using the vinyl polysiloxane type bite registration material $Futar^{(R)}$ Occlusion, were used to take horizontal and vertical impression. Improved stone models were fabricated. The amount of occlusal surface discrepaneies, interabutment distance discrepancies, amount of marginal defect were evaluated with the $X-PLAN360d^{(R)}$ and photoscanning. The results were as follows. 1. There was no significant difference in occlusal surface according to the directions and techniques of impression taking. 2. There was no significant difference in interabutment distance discrepancies according to the directions and techniques of impression taking 3. There was no significant difference in marginal discrepancies according to the direction of impression taking but there was significant difference between one-step technique and individual tray technique, individual tooth tray technique (P<0.05). Taken together, these results suggest that individual tray technique and individual tooth tray technique are more accurate for impression taking than one-step technique.

• 대한치과보철학회지
• /
• 제38권2호
• /
• pp.242-254
• /
• 2000

Accurate impression is very important to achieve desirable prosthesis and there are many factors in taking a good impression. For example, types of impression material, types of impression tray, impression taking methods and so on. Recently individual tooth tray technique is accepted as obtaining good impression that can be applied to multiple abutment impression, heavy salivated patient, to minimize the effect of natural teeth s undercuts and to reduce pain during cord packing procedures. The purpose of this study was to compare the accuracy according to materials and forms of the individual tooth tray which is clinically applied nowadays. Used materials in experiment were divided into 3 types (acrylic resin. $Futar^{(R)}$ occlusion. $Blu-mousse^{(R)}$) and forms were divided into 2 types (forming occlusal vent hole or not and forming marginal vent space or not). Stone master model from impression body and metal master model were measured by $X-PLAN360d^{(R)}$ to compare occlusal surface discrepancy and marginal discrepancy. The results were as follows: 1. In comparison of occlusal surface discrepancy and marginal discrepancy according to materials, groups with three materials showed no statistical difference 2. In comparison of occlusal surface discrepancy and marginal discrepancy according to occlusal vent hole, groups with occlusal vent hole showed significantly less marginal discrepancy than groups with no occlusal vent hole(p<0.05). 3. In comparison of occlusal surface discrepancy and marginal discrepancy according to 0.5mm-marginal-vent-space, groups with no 0.5mm-marginal-vent-space showed significantly less marginal discrepancy than groups with 0.5mm-marginal-vent-space (p<0.05). In summary these results suggest that individual tooth tray made of 3 types of materials with occlusal vent hole and individual tooth tray made of acrylic resin with no marginal vent space showed good accuracy of impression. In addition, individual tooth tray which is made of bite registration materials may be more useful because of advantage in facility and timesaving aspect of fabrication.

• 대한치과보철학회지
• /
• 제43권5호
• /
• pp.622-632
• /
• 2005

Statement of problem: Silicone Index Tooth Tray impression system which does not use gingicord has a shortcoming. It takes time to remove internal wall of Silicone Index Tooth Tray for space of wash impression material. Purpose: This study was to evaluate whether providing certain space to impression body can prevent from doing complicated laboratory work. Material and methods: After mounting metal dies with shoulder and chamfer margins arbiturarily, SITT was produced using $Blu-mousse^(R)$. In one experimental group, wash impression was taken using $Fit-tester^(R)$ without removing interior surface of SITT and in the other group, wash impression was taken using $Fit-tester^(R)$ providing 0.5mm space in the SITT and then compared the differences in two groups. Results: 1. There was no significant difference between a group which did not allow space and a group which granted equal 0.5mm space. 2. There was no significant difference between gingival diameter, occlusal diameter of metal die that has shoulder margin and gingival diameter, occlusal diameter of metal die that has chamfer margin. 3. There was no significant difference between a group which did not take pick-up impression and a group which took pick-up impression through relining method using SITT 4. There was no significant difference between a group that poured immediately after taking primary impression and a group that poured after removing poured stone die. Conclusions: When taking an impression of an abutment using SITT impression system, it is considered to obtain clinically identical results between a group that did not grant a 0.5mm space within SITT for wash impression and a group which invest a space. Furthermore, it is considered possible to produce an individual die through secondary pouring.

• 대한치과보철학회지
• /
• 제59권4호
• /
• pp.508-514
• /
• 2021

본 증례는 기존 의치를 스캔 후 프린팅한 복제 의치를 폐구인상시 개인트레이로 사용하였고 이에 기공 과정을 줄이고, 진료시간을 단축시킬 수 있었으며, 안모 평가가 용이하고 치아 배열을 비롯한 총의치 제작과정에 있어 기공 과정이 원활하게 이뤄질 수 있었다. 또한 일반적인 개구인상법을 이용한 제작과정에 비해 내원 횟수를 줄일 수 있었으며 기존 의치의 수직고경을 비롯한 여러 정보를 의치 제작 시 활용함으로써 환자의 새 의치 적응도를 높일 수 있었다.

• 대한치과보철학회지
• /
• 제44권5호
• /
• pp.503-513
• /
• 2006

Statement of the problem: The cold-cured resins used in fabrication of the provisional crown and fixed partial dentures could cause pulpal damage by heat generated during exothermic polymerization reactions. Purpose: In this in vitro study investigates the how external conditions such as material of the matrix, thickness of the matrix and thickness of dentin affect the temperature of the tooth during polymerization reaction of the cold-cured resins. Material and methods : To measure the temperature of the resin, metal die was maintained to the temperature of $37^{\circ}C$ with water bath to simulate the temperature of thetooth and thermocouple was placed in the center of the metal die. Acrylic pipe was cut in height of 1, 2, 3, 6, 10 mm and placed on the metal die and mixed resin was pored in the acrylic pipe As the resin polymerized temperature was recorded with the thermometer. Temperature of the resin using matrix was recorded by using the individual tray relieved in different thickness 2, 5, 7, 10 mm. The material of the matrix was irreversible hydrocolloid impression material, vinyl polysilloxane impression material and vacuum-formed template Temperature rise of the resin using different thickness of tooth section was record ed by placing tooth section on the metal die and placing resin over the tooth section. Results : Conclusion : 1. Temperature rise increased as the thickness of the resin increased but there was no significant differences over 3 mm thickness of the resin. 2. The lowest temperature rise was showed in irreversible hydrocolloid impression material and vinyl polysilloxane impression material vacuum-formed template as in orders. 3, Temperature rise of the resin decreased regardless of the thickness of the matrix when vinyl polysilloxane impression material was used as the matrix. 4 When irreversible hydrocolloid impression material was used as matrix, the temperature rise of the resin decreased as the thickness of the matrix increased and there was no temperature rise when thickness of the matrix reached 10 mm, 5. The temperature rise of the resin did not decreased when Polypropylene vacuum-formed template was used as the matrix. 6, The temperature of the resin increased as the thickness of the dentin decreased.

• 대한치과보철학회지
• /
• 제62권1호
• /
• pp.6-19
• /
• 2024

Computer aided design/Computer aided manufacturing (CAD-CAM) 기술의 발전에 따라 이를 활용한 총의치 제작 방법이 대두되고 있으며, 그 중 하나로 의치상과 인공치의 색조를 모두 포함하는 모놀리식 블록을 절삭하는 디지털 의치 시스템이 소개되었다. 본 증례는 74세 남성, 73세 여성 두 환자에서 전통적인 기존 의치 제작법, 디지털 방식의 모놀리식 블록을 절삭한 의치 제작법으로 각각 총 두 쌍의 상·하악 의치를 제작하여 비교한 증례이다. 디지털 방식의 총의치 제작 과정으로는 CAD-CAM 프로그램으로 개인 트레이를 디자인 및 3D프린팅 하여 최종인상 및 악간 관계 채득하였다. 이후 동일한CAD-CAM프로그램으로 총의치 디자인 및 시적의치를 3D 프린팅 하여 시적 하였다. 최종적으로는 모놀리식 블록(Ivotion, Ivoclar Vivadent, Schaan, Liechtenstein)을 밀링 기계(PrograMill PM7, Ivoclar Vivadent, Schaan, Liechtenstein)로 절삭하여 총의치 제작 및 장착하였다. 해당 증례에서는 CAD-CAM 시스템을 이용한 총의치 제작과 동시에 전통적 방법으로도 총의치를 제작하여2쌍의 의치의 안정 및 적합성, 발음, 저작, 심미성과 환자의 만족도를 비교, 분석하여 이를 보고하고자 한다.

• 대한치과교정학회지
• /
• 제39권2호
• /
• pp.105-111
• /
• 2009

법랑질 탈회는 교정 치료 중에 발생하는 대표적인 부작용으로서 특히 교정용 브라켓에 대한 세균 부착이 그 원인이 될 수 있다. 본 연구의 목적은 서로 다른 표면 특성을 가진 세 종류의 브라켓을 구강 내 장착했을 때 각 재료의 표면에 대한 mutans streptococci 부착 정도를 측정하여 브라켓 재료에 따른 법랑질 탈회 및 치아 우식 발생 가능성을 분석하는 것이었다. 상하악 및 치아 부위별 mutans streptococci 부착 정도의 차이를 배제하고 브라켓 원재료에 따른 차이만을 검출하기 위하여 균형완전블록 실험계획을 설계하였다. 피실험자인 30세 여성의 구강 내에 장착할 수 있는 tooth positioner 형태로 3세트의 플라스틱 맞춤 트레이를 제작하였으며, 이 트레이에 직육면체의 형태($4{\times}3{\times}2\;mm$)로 제작한 stainless steel, monocrystalline sapphire, polycrystalline alumina 조각을 세트마다 서로 다른 순서로 전치부와 구치부 순면에 부착하였다 이렇게 제작된 3종류의 실험장치를 12시간 동안 피 실험자의 구강 내에 장착한 후, 각 브라켓 재료 표면에 형성된 치태를 채취하여 bacitracin이 포함된 mitis salivarius배지에서 48시간 배양 후 colony counting을 통해 그 표면에 부착된 mutans streptococci 양을 비교하였다. 이와 같은 방법으로 3세트의 실험장치에 대해서 각각 5회씩 총 15회의 실험을 시행하였다. 그 결과 상하악 및 치아 부위별 및 브라켓 재료별 세균 부착 정도는 모두 유의한 차이를 보이지 않았다. 결론적으로 본 연구의 결과 in vivo condition에서 브라켓 재료의 차이는 mutans streptococci 부착에 영향을 미치지 못하는 것으로 보였다.