• Proceedings of the Korean Vacuum Society Conference
• /
• 2001.07a
• /
• pp.70-70
• /
• 2001

• Journal of the Korean institute of surface engineering
• /
• v.32 no.3
• /
• pp.276-280
• /
• 1999

Electrical properties of electrochromic (EC) InN thin films prepared by rf ion plating were studied. There was a correlation between the electrical properties and the electrochromism in the InN films, particularly, carrier concentration changes were responsible for the electrical resistivity changes of the films due to the electrochromism. These carrier concentration changes were caused by chemisorbed hydroxyl groups and protons. From these results, it was proved that the carrier concentration changes of the InN films was responsible for the electrochromism in the visible and near-infrared region.

• Journal of Sensor Science and Technology
• /
• v.4 no.1
• /
• pp.3-8
• /
• 1995

n-ITO/p-PSL heterojunction photodetector have been fabricated on the Si wafer by using ITO(indium tin oxide) and PSL(porous silicon layer). They were anodized selectively by using silicon nitride and Ni-Cr/Au and were passivated by using ITO as well as being isolated by using mesa structure. With white light from 0 to 3000 Lux, the photocurrent varied linearly with incident light intensity. The reverse characteristics of fabricated devices were very stable up to a bias voltage of -40V and dark current density was about $40nA/mm^{2}$. When the device was exposed by Xe lamp whose wavelength range from 400nm to 1100nm, the maximum photo responsivity was about 0.6A/W between 600 and 700nm. Variation of the characteristics of fabricated devices after 5 weeks was negligible.

• Korean Journal of Materials Research
• /
• v.18 no.10
• /
• pp.535-541
• /
• 2008

Growth behavior of InGaN/GaN self-assembled quantum dots (QDs) was investigated with respect to different growth parameters in low pressure metalorganic chemical vapor deposition. Locally formed examples of three dimensional InGaN islands were confirmed from the surface observation image with increasing indium source ratio and growth time. The InGaN/GaN QDs were formed in Stranski-Krastanow (SK) growth mode by the continuous supply of metalorganic (MO) sources, whereas they were formed in the Volmer-Weber (V-W) growth mode by the periodic interruption of the MO sources. High density InGaN QDs with $1{\sim}2nm$ height and $40{\sim}50nm$ diameter were formed by the S-K growth mode. Dome shape InGaN dots with $200{\sim}400nm$ diameter were formed by the V-W growth mode. InN content in InGaN QDs was estimated to be reduced with the increase of growth temperature. A strong peak between 420-460 nm (2.96-2.70 eV) was observed for the InGaN QDs grown by S-K growth mode in photoluminescence spectrum together with the GaN buffer layer peak at 362.2 nm (3.41 eV).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.162-162
• /
• 2010

InSb has received great attentions as a promising candidate for the active layer of infrared photodetectors due to the well matched band gap for the detection of $3{\sim}5\;{\mu}m$ infrared (IR) wavelength and high electron mobility (106 cm2/Vs at 77 K). In the fabrication of InSb photodetectors, passivation step to suppress dark currents is the key process and intensive studies were conducted to deposit the high quality passivation layers on InSb. Silicon dioxide (SiO2), silicon nitride (Si3N4) and anodic oxide have been investigated as passivation layers and SiO2 is generally used in recent InSb detector fabrication technology due to its better interface properties than other candidates. However, even in SiO2, indium oxide and antimony oxide formation at SiO2/InSb interface has been a critical problem and these oxides prevent the further improvement of interface properties. Also, the mechanisms for the formation of interface phases are still not fully understood. In this study, we report the quantitative analysis of indium and antimony oxide formation at SiO2/InSb interface during plasma enhanced chemical vapor deposition at various growth temperatures and subsequent heat treatments. 30 nm-thick SiO2 layers were deposited on InSb at 120, 160, 200, 240 and $300^{\circ}C$, and analyzed by X-ray photoelectron spectroscopy (XPS). With increasing deposition temperature, contents of indium and antimony oxides were also increased due to the enhanced diffusion. In addition, the sample deposited at $120^{\circ}C$ was annealed at $300^{\circ}C$ for 10 and 30 min and the contents of interfacial oxides were analyzed. Compared to as-grown samples, annealed sample showed lower contents of antimony oxide. This result implies that reduction process of antimony oxide to elemental antimony occurred at the interface more actively than as-grown samples.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.389-392
• /
• 2009

Metal oxides have been proposed as an alternative channel material to hydrogenated amorphous silicon in thin film transistors (TFTs) because their higher mobility and stability make them suitable for transistor active layers. Thin films of indium zinc oxide (IZO) were deposited using a High Target Utilization Sputtering (HiTUS) system on various dielectrics, some of which were also deposited with the HiTUS. Investigations into bottom-gated IZO TFTs have found mobilities of 8 $cm^2V\;^1s^{-1}$ and switching ratios of $10^6$. There is a variation in the threshold voltage dependent on both oxygen concentration, and dielectric choice. Silica, alumina and silicon nitride produced stable TFTs, whilst hafnia was found to break down as a result of the IZO.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.280-280
• /
• 2014

We report the fabrication and electroluminescent characteristics of GaN/InxGa1-xN microdonut-shaped light-emitting diode (LED) microarrays as variable-color emitters. The diameter, width, height, and period of the GaN microdonuts were controlled by their growth parameters and the geometrical factors of the growth mask patterns. For the fabrication of microdonut LEDs, p-GaN/p-AlxGa1-xN/u-GaN/u-InxGa1-xN heteroepitaxial layers were coated on the entire surface of n-GaN microdonuts. The microdonut LED arrays showed strong light emission, which could be seen with the unaided eye under normal room illumination. Additionally, magnified optical images of microdonut LED arrays exhibited microdonut-shaped light emissions having spatially resolved blue and green colors. Their electroluminescence spectra had two dominant peaks at 460 and 560 nm. With increasing applied voltage, the intensity of the blue emission peak increased much faster than that of the green emission peak, indicating that the color of the LEDs is tunable. We also demonstrated that EL spectra of the devices could be controlled by changing the size of microdonut LEDs. What we want to emphasize here with the microdonut LEDs is that they have additional inner sidewall facets which did not exist for other typical three-dimensional structures including nanopyramids and nanorods, and that InxGa1-xN single quantum well formed on the inner sidewall facets had unique thickness and chemical composition, which generated additional EL color. The origin of the electroluminescence peaks was investigated by structural characterizations and chemical analyses.

• Korean Journal of Materials Research
• /
• v.22 no.11
• /
• pp.636-641
• /
• 2012

In this study, we have investigated highly efficient nanoscale surface corrugated light emitting diodes (LEDs) for the enhancement of light extraction efficiency (LEE) of nitride semiconductor LEDs. Nanoscale indium tin oxide (ITO) surface corrugations are fabricated by using the conformal nanoimprint technique; it was possible to observe an enhancement of LEE for the ITO surface corrugated LEDs. By incorporating this novel method, we determined that the total output power of the surface corrugated LEDs were enhanced by 45.6% for patterned sapphire substrate LEDs and by 41.9% for flat c-plane substrate LEDs. The enhancement of LEE through nanoscale surface corrugations was studied using 3-dimensional Finite Different Time Domain (FDTD) calculation. From the FDTD calculations, we were able to separate the light extraction from the top and bottom sides of device. This process revealed that light extraction from the top and bottom sides of a device strongly depends on the substrate and the surface corrugation. We found that enhanced LEE could be understood through the mechanism of enhanced light transmission due to refractive index matching and the increase of light scattering from the corrugated surface. LEE calculations for the encapsulated LEDs devices also revealed that low LEE enhancement is expected after encapsulation due to the reduction of the refractive index contrast.