• Journal of Biosystems Engineering
• /
• 제27권1호
• /
• pp.33-38
• /
• 2002

The indicated power of Stirling engine was affected by the heat exchange effectiveness of the regenerator. The temperature difference of working fluid between the expansion and the compression space of Stilting engine depends on the heat exchange effectiveness of the regenerator. The influence of the temperature ratio of expansion space to compression space of Stirling engine on the indicated power was analyzed by using Schmidt analysis in this study. In the Stirring engine, as the temperature ratio increased, the indicated power generally decreased. Therefor, it is necessary to develope the regenerator of high effectiveness. The actual indicated power was shown 64.9 percent of the predicted indicated power in maximum and 47.2 percent of that in minimum due to increased dead volume of engine, the loss of flow friction and heat transfer in the regenerator.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권4호
• /
• pp.368-373
• /
• 2015

향후 박용기관의 일정 부분은 LNG 또는 합성가스를 사용한 Gas Engine으로의 이행이 예상되고 있으며 이에 대한 선행연구로서 SI기관의 시뮬레이션에 대한 연구가 요구된다. SI기관의 도시성능 예측을 위하여 상용 성능해석 소프트웨어인 GT-POWER를 이용한 모델링을 시도하였다. 이를 위해 흡 배기 계통의 모델링은 기존 연구에서 최적화된 모델링을 적용하였다. 연소과정 모델링과 열전달과정 모델링에 있어서는 현장에서 가장 적용이 용이한 모델인 SI Wiebe 연소모델과 Modified Woschni 열전달 모델을 적용하였다. 여러 운전조건에서 크랭크 각에 따른 연소실 압력 변화와 최고압력 및 도시평균유효압력 등의 계산결과를 실험결과와 비교한 결과 양자가 잘 일치함을 확인하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제33권7호
• /
• pp.1052-1059
• /
• 2009

The effects of varying the inlet flow angle on the output power of a Francis hydraulic turbine were studied numerically and the result was compared to the experimental results conducted at Korea Institute of Energy Research to determine the brake power of the turbine for each set of operating conditions. The loss of mechanical power of the model turbine was determined by comparing the numerical and experimental results, and thus the turbine efficiency or energy conversion efficiency of the model turbine could be estimated. From the result, it was found that the maximum brake efficiency of the turbine is approximately 46% at an induced angle of 35 degrees. The maximum indicated mechanical efficiency of the turbine is approximately 93% at an induced angle of 25~30 degrees.

• Nuclear Engineering and Technology
• /
• 제55권8호
• /
• pp.3017-3029
• /
• 2023

In the late in-vessel phase of a nuclear reactor severe accident, the internal heat transfer and crust evolution during the debris bed melting process have important effects on the thermal load distribution along the vessel wall, and further affect the reactor pressure vessel (RPV) failure mode and the state of melt during leakage. This study coupled the phase change model and large eddy simulation to investigate the variations of the temperature, melt liquid fraction, crust and heat flux distributions during the debris bed melting process in the hypothetical severe accident of HPR1000. The results indicated that the heat flow towards the vessel wall and upper surface were similar at the beginning stage of debris melting, but the upward heat flow increased significantly as the development of the molten pool. The maximum heat flux towards the vessel wall reached 0.4 MW/m². The thickness of lower crust decreased as the debris melting. It was much thicker at the bottom region with the azimuthal angle below 20° and decreased rapidly at the azimuthal angle around 20-50°. The maximum and minimum thicknesses were 2 and 90 mm, respectively. By contrast, the distribution of upper crust was uniform and reached stable state much earlier than the lower crust, with the thickness of about 10 mm. Moreover, the sensitivity analysis of initial condition indicated that as the decrease of time interval from reactor scram to debris bed dried-out, the maximum debris temperature and melt fraction became larger, the lower crust thickness became thinner, but the upper crust had no significant change. The sensitivity analysis of in-vessel retention (IVR) strategies indicated that the passive and active external reactor vessel cooling (ERVC) had little effect on the internal heat transfer and crust evolution. In the case not considering the internal reactor vessel cooling (IRVC), the upper crust was not obvious.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.3050-3055
• /
• 2007

A wind turbine is one of the most popular energy conversion systems to generate electricity from the natural renewable energy source and an axial-flow type wind turbine is the most popular system for the electricity generation in the wind farm nowadays. In this study, a cross-flow type turbine has been studied for the application of wind turbine for electricity generation. The target capacity of electric power generation of the model wind turbine developing on the project is 12 volts, 130A/H (about 1.56kW). The important design parameters of the model turbine impeller are the inlet and exit angle of the turbine blade, number of blade, hub/tip ratio and the exit flow angle of the casing. In this study, the radial equilibrium theorem was used to decide the inlet and exit angle of the impller blade and CFD technique was used to have the performance analysis of the designed model power turbine to find out the optimum geometry of the CPT impeller and casing. The designed CPT with 24 impeller blades at ${\alpha}=82^{\circ}$, ${\beta}=40^{\circ}$ of turbine blade angle was estimated to generate 284.6 N.m of indicated torque and 2.14kW of indicated power.

• 대한방사선기술학회지:방사선기술과학
• /
• 제41권5호
• /
• pp.457-462
• /
• 2018

The purpose of this study was to compare image quality of indirect digital radiography (IDR) system using the International Electro-technical Commission standard (IEC 62220-1), and to suggest the analysis of noise power spectrum (NPS) which were applied to IEC 62220-1 in medical imaging. In this study, Pixium 4600 (Trixell, France) which is indirect flat panel detector (FPD) was used. The size of image receptor (IR) is $7{\times}17$ inch (matrix $3001{\times}3001$) which performed 14bit processing and pixel pitch is $143{\mu}m$. In IEC standard, NPS evaluation were applied to RQA3, RQA5, RQA7 and RQA9. Because of different radiation quality, each region of interesting (ROI) were compared. The results of NPS indicated up to $3.5mm^{-1}$ including low Nyquist frequency. RQA5 indicated the lowest NPS and the others indicated higher NPS results relatively. NPS result of ROI a38 was higher than ROI a92 and this result indicated that there are more noise in left (cathode) than right (anode). This study were to evaluate NPS by using different radiation quality and setting the each ROI, and to suggest the quantitative methods of measuring NPS.

• 한국산학기술학회논문지
• /
• 제12권6호
• /
• pp.2691-2697
• /
• 2011

본 논문은 대학교 육상단거리 선수와 태권도 선수의 근력, 근 파워를 비교하기 위하여 등속성 근력검사기기를 이용하여 기초체력, 슬관절의 근력($60^{\circ}$/sec), 근 파워($180^{\circ}$/sec)를 분석하여 육상 단거리 선수와 태권도 선수의 근기능 특성을 밝히고자 하는데 목적으로 수행되었다. 기초체력은 육상 단거리 선수가 태권도 선수에 비해 높게 나타났으며, 기초체력 중 좌악력과 순발력에서 통계적으로 높게 나타났다. 슬관절의 근력은 육상 단거리 선수가 태권도 선수에 비해 높게 나타났으나, 근 파워에서는 태권도 선수가 육상 단거리 선수에 비해 통계적으로 차이가 높게 나타났다. 이와 같은 결론을 종합해 볼 때, 육상 단거리 선수와 태권도 선수는 근력뿐만이 아니라 순발력을 필요로 하고 있으며, 등속성 근 기능의 측정에서는 태권도 선수는 체중조절을 요구하는 경기의 특성 때문인지 평균파워와 체중당 평균파워에서만 통계적으로 높게 나타났다. 그러므로 차후 연구에서는 각각의 운동 종목별 근 기능을 분석을 하는 것이 필요한 실정이며, 태권도 선수와 유사한 특성을 가진 투기종목에서도 근 기능을 분석하는 연구가 필요 할 것으로 사료된다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.447-447
• /
• 2005

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 춘계학술발표대회 개요집
• /
• pp.144-146
• /
• 2005

Measurements of Thermoelectric power (TEP) were used to evaluate microstructural analysis in HSLA steel weldments. The measurements of TEP for weld microstructure across weldment have shown good correlation with hardness profile. The different TEP values indicated that changes in weld microstructure can be correlated with TEP values measured.

• Journal of Nutrition and Health
• /
• 제22권3호
• /
• pp.159-166
• /
• 1989

The effect of blanching time and power settings of microwave oven on the ascorbic acid retention in seven kinds of vegetables were investigated. The vegetable were blanched for 120 or 180 sec. at three different power setting, 650 watt(high power), 500 watt(medium power) and 160 watt(low power). The retentions of ascorbic acid in cabbage, garland chrysanthemum, mungbean sprout, amaranth and carrot were higher when they were blanched at the high power than those blanced at the lower power stettings. Blanching of spinach and yul-moo(small korean radish) showed that the vitamin was more retained by the medium power heating. Blanching at the low power revealed that the ascorbic acid retention was reduced remarkably as the blanching time increased. From the scoring difference tests the 10-panel members indicated that the texture of three-tested vegetables was more acceptable when they were blanched at the high power setting.