• Restorative Dentistry and Endodontics
• /
• v.38 no.2
• /
• pp.85-89
• /
• 2013

When a patient with a fractured anterior tooth visits the clinic, clinician has to restore the tooth esthetically and quickly. For esthetic resin restoration, clinician can use 'Natural Layering technique' and an index for palatal wall may be needed. In this case report, we introduce pre-restoration index technique on a Class IV defect, in which a temporary filling material is used for easy restoration. Chair-side index fabrication for Class IV restoration is convenient and makes a single-visit treatment possible.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.390-390
• /
• 2008

In this paper, we have designed and fabricated optical waveguides based on the Mach-Zehnder Interferometer (MZI) for application to sensor. The evanecent-wave sensor based on the MZI principle has sufficiently high sensitivity to measure the change of the refractive index on surface of a waveguide. The waveguides were optimized at a wavelength of 1550 nm and fabricated according to the design rule of 0.45 delta%, which is the difference of refractive index between the core and clad. The fabrication of MZI optical waveguides was performed by a conventional Planar Lightwave Circuit (PLC) fabrication process. The fabricated MZI optical waveguide device was measured. According to the measurement result, the insertion loss of MZI optical waveguide device was below 3.5 dB and the polarization dependent loss (PDL) was within 0.1dB. In addition, we analyzed optical properties of MZI sensor according to the refractive index change of the sensor arm.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.12 s.177
• /
• pp.16-21
• /
• 2005

Photonic crystals, periodic structure with a high refractive index contrast modulation, have recently become very interesting platform for the manipulation of light. The existence of a photonic bandgap, a frequency range in which the propagation of light is prevented in all directions, makes photonic crystal very useful in application where the spatial localization of light is required, for example waveguide, beam splitter, and cavity. However, the fabrication of 3 dimensional photonic crystals is still difficult process. A concept that has recently attracted a lot of attention is a planar photonic crystal based on a dielectric membrane, suspended in the air and perforated with two dimensional lattice of hole. The fabrication of Si master with pillar structure using hot embossing process is investigated for two dimensional, low-index-contrast photonic crystal waveguide. From our research we show that the multiple stamp copy process proved to be feasible and useful.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.498-501
• /
• 2005

Photonic crystals, periodic structure with a high refractive index contrast modulation, have recently become very interesting platform for manipulation of light. The existence of a photonic bandgap, a frequency range in which propagation of light is prevented in all direction, makes photonic crystal very useful in application where spatial localization of light is required for waveguide, beam splitter, and cavity. But fabrication of 3 dimensional photonic crystal is still difficult process. a concept that has recently attracted a lot of attention is a planar photonic crystal based on a dielectric membrane, suspended in the air, and perforated with 2 dimensional lattice of hole. We show that the polymer slabs suspended in air with triangular lattice of air hole can exhibit the in-plane photonic bandgap for TE-like modes. The fabrication of Si master with pillar structure using hot embossing process was investigated for 2 dimensional low-index-contrast photonic crystal waveguide.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.14 no.4
• /
• pp.307-320
• /
• 1989

This paper presetns new design of the Modified Chemical Vapor Deposition(MCVD) system for optical fiber preform fabrication. It contains a glass working lathe, raw material supplier and exhaust gas treatment apparatus as fundamental instruments for MCVD process, graded index fiber design, characteristic of process and the experimenta arrangement to measure the refractive index profile of MCVD preforms, respectively. From the investigation results, it is shown that an ideal graded index fiber preform does not exhibit a center dip or bump.

• Korean Journal of Optics and Photonics
• /
• v.7 no.4
• /
• pp.375-385
• /
• 1996

Recently interest in the fabrication of LD operated by low current is gradually increasing as fabrication techniques of MQW-LD are progressed. In this viewpoint, theoretical estimation for decreasing the amount of threshold current will be helpful to design and make LD in case that active layer of conventional bulk type RWG-LD structure is replaced with MQW structure. Therefore, the optimum design condition of RWG MQW-LD was obtained from theoretical analysis in order to operate in the weakly index-guided LD and low threshold current. The lateral effective index step has been obtained in RWG MQW-LD structure. Waveguide mechanism including this index step has been investigated by solving the carrier diffusion equation and lateral wave equation. From these theoretical results, the optimum design condition of RWG MQW-LD have been suggested.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.840-845
• /
• 2005

This paper presents a robust optimal design method for a periodic structure type of MEMS resonator that is vulnerable to mode localization. The robust configuration of such a MEMS resonator to fabrication error is implemented by changing the regularity of periodic structure. For the mathematical convenience, the MEMS resonator is first modeled as a multi pendulum system. The index representing the measure of mode variation is then introduced using the perturbation method and the concept of modal assurance criterion. Finally, the optimal intentional mistuning, minimizing the expectation of the irregularity measure for each substructure, is determined for the normal distributed fabrication error and its robustness in the design of MEMS resonator to the fabrication error is demonstrated with numerical examples.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.8 s.101
• /
• pp.931-938
• /
• 2005

This paper presents a robust optimal design method for a periodic structure type of MEMS resonator that is vulnerable to mode localization. The robust configuration of such a MEMS resonator to fabrication error is implemented by changing the regularity of periodic structure For the mathematical convenience, the MEMS resonator is first modeled as a multi-pendulum system. The index representing the measure of mode variation is then introduced using the perturbation method and the concept of modal assurance criterion. Finally, the optimal intentional mistuning, minimizing the expectation of the irregularity measure for each substructure, is determined for the normal distributed fabrication error and its robustness in the design of MEMS resonator to the fabrication error is demonstrated with numerical examples.

• Proceedings of the Optical Society of Korea Conference
• /
• 1999.08a
• /
• pp.140-141
• /
• 1999

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.962-965
• /
• 1999

We designed and fabricated a travelingwave CPW(coplanar waveguide) electrode for LiNbO$_3$ optical modulator. To Investigate the variation of microwave refractive index of these electrodes, we prepared the CPW electrode samples as a function of electrode thickness and measured the TDR and S-parameter. From this results, we could know the electrode conditions of index matching to 2.20 for 1550nm optical wave index for applying LiNbO$_3$ optical modulator and described. Also, we discussed the some properties of CPW electrode for applying LiNbO$_3$ optical modulator.