• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2002.05a
• /
• pp.38-38
• /
• 2002

Kinetic indentation technique was studied and a method to evaluate wear and fatigue behaviors of irradiated small specimen was suggested. The method is based on both the proportion of elastic and plastic deformation and values obtained by micro-hardness test. The parameters obtained from the diagram of load-indentation depth-time are required to evaluates wear and fatigue properties. Considering the irradiated test specimen, it is one of possible and useful methods to estimate the irradiated wear and fatigue behaviors of the small size specimen. This article briefly describes the status of irradiated material study in domestic research reactor.

• Journal of Power System Engineering
• /
• v.8 no.2
• /
• pp.12-17
• /
• 2004

In this study, to verify the reliability of the indentation for measuring welding residual stresses to get in method we compared the results of the method with those measured by the saw cutting method. Also for the same purpose we used a 4-point bending test and confirmed the reliability of indentation method. The specimens used in this experiment are made with the same conditions for hot reheater pipes and cold reheater pipes used in the electric power plant. Therefore we could know that the results of the methods showed the reliability of the method to obtain welding residual stresses.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.294-297
• /
• 2009

The frictional behaviors of Cermets/Cr-Ceramics and Cu-Al coatings of piston ring were investigated. Friction tests were carried out by pin-on-disk test and materials properties of coating layer were analyzed by nano indentation tester. Higher friction coefficient was obtained at harder coating with rougher surface. In case of hard-coating, the scratch depth, width and pile-up height had close relationship with indentation hardness. So the scratch width, depth and pile-up height increases with decreasing friction coefficient. But in case of soft-coating, the friction coefficients are strongly dependent on the morphological characteristics after nano scratching more than indentation hardness.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.268-271
• /
• 2010

In this paper, forward and reverse analysis is introduced in order to estimate the elastic-plastic properties from a power-law hardening bulk specimen materials with one simple spherical indentation impression test. In order to verify the reliability of the reverse analysis, we have simulated about a large range of materials that essentially cover all engineering materials, using ABAQUS(6.91) program. Then, we could obtained the fitting functions and plastic parameters from the numerical analysis results. Next, through the procedure of reverse analysis we can obtain the yield stress and power-law exponent. Finally, obtain good agreement between the result from reverse analysis and initial input data from experiment.

• Journal of the Korean Ceramic Society
• /
• v.48 no.5
• /
• pp.396-403
• /
• 2011

In this study, we investigated the mechanical behaviors of layered thermal barrier coatings by indentations. Various single and double-layered thermal barrier coatings were deposited by air plasma spray process using different type of commercialized YSZ (Yttria stabilized zirconia) starting powders. Indentation stress-strain curve, load-displacement curve and hardness of the single and the double-layered thermal barrier coatings were obtained experimentally and analyzed. The indentation damages at the same loads were compared, and thus, the results depend on the structure of each coating. The result indicates improvement in damage resistances from tailoring of layered structures in the component of gas turbine system is expected.

• Journal of the Korean Ceramic Society
• /
• v.56 no.1
• /
• pp.77-83
• /
• 2019

MgO-C refractories are used in basic furnaces and steel ladles due to their many desirable properties, such as excellent thermal shock resistance via low thermal expansion, and high thermal conductivity. However, the mechanical and thermal properties of the refractory continuously deteriorate by spalling phenomena and pore generation due to the oxidation of graphite, used as a carbon source, indicating that the characteristics and performance of MgO-C refractories need to be improved by using a new material or composition. In this study, the use of a Hertzian indentation test as a method for determining the damage and fracture behavior of an MgO-C refractory is described. The results highlight that Hertzain indentation tests can be one of the important evaluation tools for quasi-plastic damage accumulation of MgO-C refractories during falling process of scrap metal.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.05a
• /
• pp.248-254
• /
• 2002

The most controversial topics in plasma sprayed ceramic coating system are recently mechanical properties such as bond strength, cohesive strength, toughness and so on. Determination of bond strength of coatings is one of the most important problems. In the industry, the bond strength of coating system has been estimated by Pull-off test(ASTM standard C633-79). But, without a fixed jig and specimen, it is impossible to obtain the bond strength. Therefore, it is necessary to study the critical fracture load on interface of the coating by indentation test. Because the critical fracture load plays an important role in evaluating the bond strength for plasma sprayed ceramic coating system. So, we have estimated critical fracture load in plasma sprayed ceramic coating system, and it was shown that inverse relationship between the cross-section hardness of coating and the critical fracture load(Pc). In case of the high load(1kgf, 2kgf) in $Al_{2}O_{3}+13%TiO_{2}$, it was found that the critical point(Pco), which the coating was broken on.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.5
• /
• pp.8-15
• /
• 2018

Films with special properties (e.g., water-repellent films, optical films, anti-reflection films, and flexible films) are referred to as functional films. Recently, there has been interest in fine patterning methods for film fabrication. In particular there have been many studies that use a UV nanoimprint process involving a UV curing method. In this paper, a polymer film was fabricated by the UV nanoimprint process with a micro-pattern, and its durability was evaluated by a wear test and a nano-indentation test. The film mechanical properties (such as coefficient of friction, hardness, and modulus of elasticity) were measured. Moreover, the choice of PUA type resin used in the UV nanoimprint process was confirmed to impact the durability of the thin film. Despite making the polymer film samples using the same method and PUA type resin, different coefficient of friction, hardness, and modulus of elasticity values were obtained. PUA 4 resin had the most favorable coefficient of friction, hardness, and modulus of elasticity. This material is predicted to produce a high durability functional film.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1744-1748
• /
• 2007

In this study, the Johnson-Kendall-Roberts (JKR) theory was combined with the instrumented indentation technique (IIT) to evaluate work of adhesion and modulus of elastomeric polymer. Indentation test was used to obtain the load-displacement data for contacts between Tungsten Carbide indenter and elastomeric polymer. And the JKR contact model, contrived to take viscoelastic effects of polymer into account, was applied to compensate the contact area and the elastic modulus which Hertzian contact model would underestimate and overestimate, respectively. Besides, we could obtain the thermodynamic work of adhesion by considering the surface energy in this contact model. In order to define the relation between JKR contact area and applied load without optical measuring of contact area, we used the relation between applied load and contact stiffness by examining the correlation between JKR contact area and stiffness through dimensional analysis with 14 kinds of elastomeric polymer. From this work, it could be demonstrated that the interfacial work of adhesion and elastic modulus of compliant polymer can be obtained from a simple instrumented indentation testing without area measurement, and provided as the main algorithm of compliant polymer characterization.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.9
• /
• pp.951-959
• /
• 2007

In this study, the Johnson-Kendall-Roberts(JKR) theory was combined with the instrumented indentation technique (IIT) to evaluate work of adhesion and modulus of elastomeric polymer. Indentation test was used to obtain the load-displacement data for contacts between Tungsten Carbide indenter and elastomeric polymer. And the JKR contact model, contrived to take viscoelastic effects of polymer into account, was applied to compensate the contact area and the elastic modulus which Hertzian contact model would underestimate and overestimate, respectively. Besides, we could obtain the thermodynamic work of adhesion by considering the surface energy in this contact model. In order to define the relation between JKR contact area and applied load without optical measuring of contact area, we used the relation between applied load and contact stiffness by examining the correlation between JKR contact area and stiffness through dimensional analysis with 14 kinds of elastomeric polymer. From this work, it could be demonstrated that the interfacial work of adhesion and elastic modulus of compliant polymer can be obtained from a simple instrumented indentation testing without area measurement, and provided as the main algorithm of compliant polymer characterization.