• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.373-381
• /
• 2017

Kyeonggi Provincial Government is considering double decker bus service to solve the problem of heavy rush hour traffic. However, the height-to-width ratio is more than 1.16 times larger than that of a general high-speed single decker bus, and the center of gravity is higher. This could cause driving stability problems, such as turnover and breakaway from the lane, especially under strong side-wind conditions at high speed. In this numerical study, the driving characteristics of a model double decker bus were reviewed under side-wind and superelevation conditions at high driving speed. The rolling, pitching, and yawing moment of the model bus were calculated with CFD numerical simulation, and the results were compared to the recovery angular moments of the model bus to evaluate the dynamic stability under given driving conditions. As the model vehicle moves on a straight level road, it is stable under any side-wind conditions. However, on a curved road under side-wind conditions, it could reach unstable conditions dynamically. There is a chance that the bus will turn over when it moves on a curved road with a radius of gyration less than 100 m under side-wind (15 m/s). However, there is a very small chance of breakaway from the lane under any driving conditions.

• Wind and Structures
• /
• v.22 no.2
• /
• pp.253-272
• /
• 2016

The paper concerns with the method and results of wind tunnel investigations of the Strouhal number (St) of a stationary iced cable model of cable-supported bridges with respect to different angles of wind attack. The investigations were conducted in the Climatic Wind Tunnel Laboratory of the Czech Academy of Sciences in $Tel{\check{c}}$. The methodology leading to the experimental icing of the inclined cable model was prepared in a climatic section of the laboratory. The shape of the ice on the cable was registered by a photogrammetry method. A section of an iced cable model with a smaller scale was reproduced with a 3D printing procedure for subsequent aerodynamic investigations. The St values were determined within the range of the Reynolds number (Re) between $2.4{\cdot}10^4$ and $16.5{\cdot}10^4$, based on the dominant vortex shedding frequencies measured in the wake of the model. The model was oriented at three principal angles of wind attack for each of selected Re values. The flow regimes were distinguished for each model configuration. In order to recognize the tunnel blockage effect the St of a circular smooth cylinder was also tested. Good agreement with the reported values in the subcritical Re range of a circular cylinder was obtained. The knowledge of the flow regimes of the airflow around an iced cable and the associated St values could constitute a basis to formulate a mathematical description of the vortex-induced force acting on the iced cable of a cable-supported bridge and could allow predicting the cable response due to the vortex excitation phenomenon.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.6
• /
• pp.99-108
• /
• 2010

In this study, the characteristics of flow within and around a crossroad connected symmetrically with four roads are numerically analyzed by using a two-dimensional well-balanced HLLC finite volume model. As results of simulations and analyses, the numerical model employed in this study describes relatively well the complex water surface in a crossroad according to the conditions of inflow and road slope. Moreover, the predicted temporal and spatial variations of water depths in a crossroad and outflows at two downstream boundaries agree relatively well with laboratory measurements.

• Journal of Biosystems Engineering
• /
• v.31 no.4 s.117
• /
• pp.334-341
• /
• 2006

This study designed to develop a mower which can reach to side of a tractor or inclined road side and operate weeding. The prototype consists of 4 parts; the base and turning equipment, the boom, the arm, the weeder. The hydraulic actuators were divided into two operations, weeding and operation of boom and they were controlled by electrical equipment. Weeding was very effective when pressure set up at $15{\ell}/min$ using weeding, as $2.27kg{\cdot}m$, 2,210rpm. Weeding range of flail mower was 1.1 to 2.6m from the center of turning equipment at a flat. In case of disk mower, it was 1.5 to 2m. As a result of operation test, flail mower was appropriate for weeding at fence and short weeds, disk mower was appropriate for long weeds.

• Journal of the Korean Society of Safety
• /
• v.30 no.5
• /
• pp.67-73
• /
• 2015

In this paper, the simple truss model was modified to predict the punching shear strength of long-span prestressed concrete (PSC) deck slabs under wheel load including the effects of transverse prestressing and long span length between girders. The strength of the compressive zone arounding punching cone was evaluated by the stiffness of inclined strut which was modified by considering aging effective modulus. The stiffness of springs which control lateral displacement of the roller supports consists of the steel reinforcement and prestressing which passed through the punching cone. Initial angle of struts was determined by the experimental observation to compensate for uncertainties in the complexities of the punching shear. The validity of computed punching shear strength by modified simple truss model was shown by comparing with experimental results and the experimental results were also compared with existing punching shear equations to determine level of predictability. The modified simple truss model appeared to better predict the punching shear strength of PSC deck slabs than other available equations. The punching shear strength, which was determined by snap-through critical load of modified simple truss model, can be used effectively to examine punching shear strength of long span PSC deck slabs.

• International Journal of High-Rise Buildings
• /
• v.3 no.3
• /
• pp.167-171
• /
• 2014

TORANOMON HILLS is the main building of a large-scale re-development project located in the center of Tokyo. This high-rise building has a height of 247 m and 52 floors above ground, 5 floors below ground, and $62m{\times}80m$ in plan. It is used as hotel, residential facilities, offices, shops and conference facilities. The super structure is mainly a rigid steel frame with response-control devices, using concrete-filled steel tube columns. The underground section is a mixed structure composed of steel, steel-reinforced concrete and reinforced concrete framings. The piled-raft foundation type is used. The remarkable feature of this high-rise building is that the motorway runs through the basements of the building, which makes it stand just above the motorway. This condition is an important factor of the building design. The plan shape is designed to fit along the curve of the motorway. Special columns at the corners are required to avoid placing columns in the motorway. This special column is a single inclined column in the lower floors that branches into two columns in the mid-floors to suit the column location in the upper floors. The cast steel joint is used for the branching point of each special column to securely transfer the stress.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.18 no.3
• /
• pp.329-334
• /
• 2008

It is well-known that a kind of wheel drive mechanism is usefully employed in various service robots. One of the essential requirements for such robots is regarded as the capability of climbing that enables them to run on an inclined road smoothly. So, this paper considers the capability of climbing in a wheel drive robotic mechanism and proposes a necessary discriminating condition to determine the specification of a driving actuator which will be employed. Consequently, it is expected that the proposed discriminating condition can be applied to wheel drive robotic mechanisms in the design aspect.

• Wind and Structures
• /
• v.37 no.5
• /
• pp.331-346
• /
• 2023

This work investigates the effects of transverse inclination on an aeroelastic prism through forced-vibration wind tunnel experiments. The aerodynamic characteristics are tri-parametrically evaluated under different wind speeds, inclination angles, and oscillation amplitudes. Results show that transverse inclination fundamentally changes the wake phenomenology by impinging the fix-end horseshoe vortex and breaking the separation symmetry. The aftermath is a bi-polar, one-and-for-all change in the aerodynamics near the prism base. The suppression of the horseshoe vortex unleashes the Kármán vortex, which significantly increases the unsteady crosswind force. After the initial morphology switch, the aerodynamics become independent of inclination angle and oscillation amplitude and depend solely on wind speed. The structure's upper portion does not feel the effect, so this phenomenon is called Base Intensification. The phenomenon only projects notable impacts on the low-speed and VIV regime and is indifferent in the high-speed. In practice, Base Intensification will disrupt the pedestrian-level wind environment from the unleashed Bérnard-Kármán vortex shedding. Moreover, it increases the aerodynamic load at a structure base by as much as 4.3 times. Since fix-end stiffness prevents elastic dissipation, the load translates to massive stress, making detection trickier and failures, if they are to occur, extreme, and without any warnings.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.8 no.3
• /
• pp.229-238
• /
• 2015

This study was conducted to develop electronic control system of weeding implement that can operated at various areas such as slope land and inclined road side. The weeding implement consists of five main parts; the electronic control system, the hydraulic system, the main frame, the boom and arm mechanism, and the rotary type weeder. And the weeding implement was developed to be attached by three-point hitch of tractor considering the use of electronic control system. As a result, the electronic control test was conducted with the weeding implement attached to tractor in slope land. The results of the electronic control system test showed satisfactory weeding performance.

• Resources Recycling
• /
• v.17 no.1
• /
• pp.3-11
• /
• 2008

The treatment of domestic municipal solid waste has inclined to incineration process instead of disposal in landfills. So, the amount of ash generated by incineration of municipal solid waste is gradually increased. The incineration ash divides into bottom ash and fly ash. The bottom ash which accounts for about 90% of the incineration ash consists of ceramics, glasses and metals. And it can be used as the recycling product by the stabilization process. For example, the bottom ash is used as secondary building material or for other similar purposes such as road sub-bases and noise barrier in USA, Europe and Japan. But, the stabilization-treatment technique of bottom ash sti11leaves much to be desired in Korea. Thus, the domestic study of recycling about bottom ash must be improved through investigation about the chemical property and technique of stabilization.