• 제목/요약/키워드: In-water cleaning

검색결과 648건 처리시간 0.033초

합성섬유 충진 여과수로를 이용한 건설사업장의 흙탕물 처리 및 배수구 보호에 관한 실험적 연구 (Experimental Study on Synthetic Fiber Filled Channel for Treating Turbid Water at the Construction Sites and Protecting Drain System)

  • 원경과;청징;박기수;김영철
    • 한국물환경학회지
    • /
    • 제32권6호
    • /
    • pp.537-545
    • /
    • 2016
  • In order to cope with the new and strict government regulations for turbid water discharge from construction sites, this study tested whether synthetic fiber filters can replace conventional best management practices. The filter efficiency was about 10 to 60% with a varying filter depth of 5 to 15cm, presuming extreme storm flow conditions to be in the range of 800 to 1500m/day of filtration rates. Fiber filter acts exactly like a granular filter, i.e. the separation efficiency is directly and inversely proportional to filter depth and rate, respectively. Based on the operational data, we suggested the Log-Log design relationship, which can be used to determine the filter depth and area. Compared to the widely used gravel filter which treats the turbid water at the construction site, about 20% higher efficiency was obtained under similar operating conditions. Cleaning the filter through a simple hand-washing method at the time of break-through, achieved about 90% soil recovery.

괴화추출물에 의한 견섬유의 염색성 (Dyeing of Silk with Chinese Scholar Tree Extract)

  • 배정숙;김성숙
    • 한국염색가공학회지
    • /
    • 제12권3호
    • /
    • pp.183-191
    • /
    • 2000
  • The dyeing of silk fabric with chinese scholar tree extract was investigated. The colorant was extracted with distilled water, and concentrated under reduced pressure, and, finally spray-dried. The optimum temperature and dyeing time for the dyeing of silk with the scholar tree extract was $60^\circ{C}$ and 60 minutes respectively. In mordant dyeing, pre-mordanting method was most effective for color yield, and 1~2 % of mordant concentration was acceptable. Fastness of the dyed silk fabric to laundering and rubbing was shown to be good, but fastness to light, dry cleaning, and perspiration were varied with used mordants.

  • PDF

몰리브덴 선광광미 응집여과액 재활용을 위한 부유선별 특성 (Flotation for Recycling of a Waste Water Filtered from Molybdenite Tailings)

  • 박철현;전호석;한오형;김병곤;백상호;김학순
    • 한국광물학회지
    • /
    • 제23권3호
    • /
    • pp.235-242
    • /
    • 2010
  • 동원 NMC 선광장의 부유선별 프로세스를 유지하면서 광미여과액을 순환수로 활용하기 위한 pH 조절 연구를 수행하였다. 휘수연석(molybdenite)과 석영의 등전점(IEP)은 각각 pH 3 이하와 pH 2.7이었으며 안정화(분산)된 영역은 pH 5~10이었다. 순환수 현탁액의 경우, 잔류응집제의 의해 휘수연석의 제타전위는 pH 4 이상에서 -10 mV 이하로 감소하였다. pH 조절에 의한 부유선별 결과, 알칼리 영역에서 폴리머 사슬의 신장 및 확장, 칼슘 양이온($Ca^{2+}$)의 가교(ion bridge), 그리고 일부 무극성 폴리머/소수성 입자의 상호작용에 의한 응집 현상으로 부선효율이 급격히 저하되었다. 반면 약산성 영역(pH 5.5~6)은 수소이온에 의해 음이온성 폴리머가 중화되고 고분자 사슬의 기능이 약화됨에 따라 부선효율이 향상되었다. 조선부선 이후 정선부선의 최적조건인 pH 5.5, 포수제(kerosene) 20 g/t, 기포제(AF65) 50 g/t, 억제제($Na_2SiO_3$) 300 g/t, 정선횟수 2회에서 Mo 품위와 회수율이 각각 52.7%와 90.1%인 최종 정광을 얻어 광미여과액을 분쇄-조선-정선 공정에 지속적으로 재활용할 수 있는 기술을 개발하였다.

이젝터를 이용한 다관식 열교환기 파울링 자동제거장치의 구동특성에 관한 실험적 연구 (An Experimental Study of Operating Characteristics on Fouling Auto Removal Apparatus of Multi Pass Type Heat Exchanger using Ejector)

  • 김재돌
    • 동력기계공학회지
    • /
    • 제13권6호
    • /
    • pp.63-69
    • /
    • 2009
  • The experiment was performed to check operating characteristics of fouling auto removal apparatus for multi pass type heat exchanger using ejector. The results showed as following. The ejector suction flow rate increased with the head of operating pump of ejector. Proper suction flow rate showed $7.2{\sim}10.2m^3/h$ for ball collection in case of pump head 35~50m. The head of ejector outlet pipe is below 4.1m in case of 40m, the head of operating pump of ejector to confirm ejector suction flow rate 8.4m3/h. Lattice space of ball separator is allowed 6~10.3mm in ranges of ball diameter are 15~25mm and when mass flow of cooling water is 3.0m/sec. Average of passing time of balls is 1.2~2.8sec depend on the velocity of flow and the size of balls.

  • PDF

저에너지 대면적 전자빔 발생장치 개발에 관한 연구 (A Study on the Low-energy Large-aperture Electron Beam Generator)

  • 조주현;최영욱;이홍식;임근희;우성훈;이광식
    • 대한전기학회논문지:전기물성ㆍ응용부문C
    • /
    • 제48권12호
    • /
    • pp.785-790
    • /
    • 1999
  • This research has been carried out to develop a low-energy large-aperture pulsed electron beam generator (LELA), 200keV 1A, for industrial applications. One of the most important feature of this electron beam generator is large electron beam cross section of $190cm^2$. Low energy electron beam generators have been used for water cleaning, flue gas cleaning, and pasteurization, etc. In these applications the cross sectionof the e-beam is related to reaction efficiency. Another important feature of this LELA EB generator is easy maintenance because of its simple structure and relatively low vacuum operation compared to the conventional EB generators. The conventional EB generators need to be scanned because the small cross section thermal electron emitters are used in the conventional EB generators which have small EB cross section. In this research, we use the secondary electrons generated by ion bombardment on the HV cathode surface as a electron source. Therefore we can make any shape of EB cross section without scanning.

  • PDF

자화장치와 퀀텀스틱을 이용한 노후터널의 배수공내 침전물 방지 방법 (The Control Method of Scale in Drainage Pipe of Deteriorated Tunnel used Magnetic Field and Quantum Stick)

  • 남중우;이창기;이종휘;도종남;천병식
    • 한국지반환경공학회 논문집
    • /
    • 제12권11호
    • /
    • pp.59-64
    • /
    • 2011
  • 배수공의 막힘 현상은 노후화된 터널의 가장 큰 문제점으로 보수 대책 공법이 시급한 실정이다. 현재는 Water Jet Cleaning과 배수공내 초고압수를 분사하는 방식 등으로 배수공내 생성된 스케일을 제거하고 있다. 하지만 이러한 공법은 비용이 비싸고 주기적으로 관리가 필요하다는 단점을 가지고 있다. 본 연구에서는 이러한 문제점을 해결하고 영구적으로 배수공내 침전물 생성을 방지하기 위하여 자화장치와 퀀텀스틱 신기술을 적용하여 배수공내 스케일의 주성분인 탄산칼슘($CaCO_{3}$) 침전물을 SEM분석과 XRD분석을 통하여 관찰하였다. SEM분석과 XRD분석 결과, 자화장치를 적용하였을 경우 탄산칼슘($CaCO_{3}$)의 생성입자가 Calcite에서 Aragonite로 변화하는 것을 볼 수 있었으며, 퀀텀스틱의 경우에도 육안으로 관찰하였을 경우 스케일의 생성량이 확연히 줄어들었음을 볼 수 있었다. 전반적으로, 자화장치와 퀀텀스틱을 이용하여 배수공 내 침전물 생성을 방지하는데 효과가 있음을 확인할 수 있었다.

Development of a Sunscreen Stick Formulation which is Water Resistant but Easily Washable

  • Choi, Minsung;Song, Seungjin;Kang, Nae-Gyu
    • Korea Journal of Cosmetic Science
    • /
    • 제2권1호
    • /
    • pp.21-31
    • /
    • 2020
  • The aim of this study is to develop a sunscreen stick formulation technology with excellent water resistance and washability. Consumers' needs for sunscreen products are diversifying. Water resistance and ease of washing are both important factors in sunscreen products. However, it is difficult to develop a sunscreen formulation that satisfies these two factors at the same time, because these two elements are in conflict. Fatty acid has a hydrophobic property against the water with low or neutral pH, but when it contacts with soapy water which has high pH, saponification occurs and the fatty acids become surfactants and can be dispersed in the water. Using the reaction characteristics of fatty acids, we can make sunscreen that is highly resistant to water or sweat, but is only selectively removed from soapy water. We found that the sunscreen stick containing fatty acids had better water resistance and washability than the sunscreen sticks without fatty acid. The sunscreen stick containing fatty acids showed a tendency to improve water resistance by scattering ultraviolet rays of long wavelength area by forming insoluble precipitation with divalent ions in tap water after immersion. In addition, an increase in the fatty acid content tended to also increase the ease of cleaning the sunscreen stick. Solid fatty acid was advantageous in improving water resistance than liquid fatty acid, but there was no difference between solid fatty acids and liquid fatty acid in washability. When it comes to stability, the sunscreen stick using liquid fatty acids maintained a high hardness and melting point, and showed no sweating. Based on this study, it is possible to develop an easy washable sunscreen stick formulation technology that has excellent water resistance but is selectively removed only in soapy water.

천수용 다기능 해양폐기물 수거시스템 개발(PART II : 시스템 구성 및 성능시험) (Development of Multi-purpose Marine Wastes Cleaning Systems for the Shallow Waters(PART II : System Development and Performance Evaluation))

  • 조용진;문일성;신명수;유정석;강창구
    • 한국해양환경ㆍ에너지학회지
    • /
    • 제5권2호
    • /
    • pp.62-67
    • /
    • 2002
  • 본 연구는 '천수용 다기능 해양폐기물 수거시스템 개발(PART I 초기 개념설계)'의 후속연구로서, 천수용 다기능 해양폐기물 수거시스템의 시스템 구성 및 성능시험 결과에 대하여 논한다(조[2003]). 수거깊이 15미터 이내의 항내 침적폐기물의 수거를 위한 다관절 수거시스템과 100미터 이내의 예인식 수거시스템이 개발되었다(해양수산부[2001]). 다관절 수거시스템은 부유폐기물, 침적 잔여폐기물의 수거, 작업의 고효율화를 위한 스틸와이어커터 시스템도 포함이 되어 다기능화 되어있다. 이 시스템의 시제품을 제작하여 수심이 낮은 해역에서 실해역 시운전을 수행, 시스템의 성능검증을 수행하였다. 결과로서, 개발된 시스템은 안전하고 원활하게 작동되어 시스템의 타당성을 입증하였다.

  • PDF

Ash 세정제에 따른 CDPF의 물리화학적 특성 (Physicochemical Characteristics of CDPF according to Ash a Cleaning agent)

  • 서충길
    • 한국산학기술학회논문지
    • /
    • 제18권4호
    • /
    • pp.641-647
    • /
    • 2017
  • 디젤 엔진은 가솔린기관에 비해 강력한 파워와 연료의 경제성 및 $CO_2$ 배출양이 적어 상용차뿐만 아니라 일반승용차에서도 시장의 수요가 지속적으로 증가하고 있다. 디젤 엔진의 연소특성상 국부적인 고온반응 영역에서 질소산화물과 확산연소 영역에서 입자상물질이 많이 배출되므로 엄격해진 배기규제를 충족시키기 위해서 자동차와 선박등 촉매후처리장치 장착의 비중이 점차 증가하고 있다. 그 중 입자상물질 저감장치로써 입자상물질필터가 장착되어 왔으나 PM중 약 50%가 연료와 엔진오일에서 석출된 재 성분이 침적되면 필터를 손상시키므로 고온의 연소방식이 아닌 세정제를 이용한 제거기술이 절실히 필요하다. 이 연구의 목적은 디젤 엔진용 촉매코팅된 디젤입자상물질필터에 침적된 재를 세정을 함에 있어서 촉매의 물질의 물리화학적인 특성을 연구하는 것이다. 30분 동안 세정제에 담근 S4 샘플은 침투력이 강한 성분으로 인하여 입자들끼리 응집되고 수축되었다. 재에 침투력이 강한 침투제와 물과 기름을 혼합시켜주는 계면활성제 성분이 적절하게 제조된 S1 샘플의 세정특성이 가장 좋았다. 침투제인 수산화칼륨과 규산나트륨 성분이 첨가된 S4 샘플의 와쉬코트 손실률은 약 13%로 증가하였다. 촉매코팅된 디젤입자상물질필터의 와쉬코트 손실률이 약 13% 이하조건에서 유해가스 성분을 저감시킬 수 있었다.

저수조의 효율적 관리를 위한 수질실태에 관한 연구 (A Study on the Water Quality for Efficient Management in the Water Tanks)

  • 박현건;류승철;전수임
    • 한국환경과학회지
    • /
    • 제18권12호
    • /
    • pp.1339-1347
    • /
    • 2009
  • This study tried to investigate and analyze the actual state such as the regional, classified, and material characteristics of the water quality in order to research the several factors by which the filtrated water of the total 250 cases can be polluted in the water tank. The 215 points (86%) clean the water tanks twice a year regularly and J-city has done the best job of cleaning the water tanks. The fifty points (20%) of the total 250 investigation points examine the water quality of the water tanks every year, however, the 175 investigation points (70%) do not execute the inspection of water quality. In the case of the regional characteristics in the water quality, the 23 points (46%) in H-county, the 17 points (34%) in S-county, and the 16 points (32%) in G-city are incongruent in the standard, and the incongruity ratio of the water quality in J-city is the lowest. The result of the classified incongruity shows that total coliforms were found at the 61 investigation points, mesophilic bacteria were found at the 27 points, and turbidity was found at the 12 points. In the case of the material incongruity, concrete was found at the 63 investigation points as the most distinguished factor, and FRP (fiberglass reinforced plastic) at the 23 points, SMC (sheet molding compound) at the 12 points, and stainless steel was found at the 2 points.