• 한국정밀공학회지
• /
• 제20권1호
• /
• pp.91-98
• /
• 2003

Removal of gas in a mold has been a big problem in pressing mold or in injection mold. Air vent has been used to solve the problem, but it has weak points such as the increased cost, the increased number of process, and vent marks on the surface of a product. In this study, the sintering method and rapid tooling method are used for making porous metal mold. Porous metal mold has many open pores, which are very small. When porous metal mold is used for pressing mold or injection mold, all process would be made short, produce cost would be down, and vent marks would be not leaved on the surface of a product. Characteristic of porous material varies from sintering conditions, which are the length of sintering time, sintering temperature and sintering atmosphere etc. This study will find optimized sintering condition for the porous metal mold.

• 한국정밀공학회지
• /
• 제20권6호
• /
• pp.123-129
• /
• 2003

Recently, the life cycle of products is rapidly shortened and then the disposal of the used mold applied in development of the product is a difficult thing. In this study, we proposed the feasibility of new three plate type mold structure for recycling by analyzing of the existing standard mold base. And in order to apply new three plate mold structure in mold design and making. we constructed the specifications for mold parts such as runner stripper plate, cavity plate, core plate and slide core unit. Also, we confirmed the possibility of recycling mold base by testing a used three plate mold for audio front panel.

• Design & Manufacturing
• /
• 제15권4호
• /
• pp.1-7
• /
• 2021

A study on in-mold punching technology for hole piercing during molding of hollow plastic parts was conducted. Considering the non-linearity of the HDPE plastic material, mechanical properties were obtained according to the change in temperature and load speed. A standard specimen for the in-mold punching test was designed to implement the in-mold punching process, and the specimen was obtained through injection molding. In order to analyze the influence of process variables during in-mold punching, an in-mold punching mold capable of controlling variables such as temperature and support pressure of the specimen was designed and manufactured. Mold heating characteristics were confirmed through finite element analysis, and punching simulations for changes in process conditions were performed to analyze punching characteristics and reflected in the experiment. Through simulations and experiments, it was found that the heating temperature, punch shape, punching speed, and pressure of the back side of the specimen were very important during in-mold punching of HDPE materials, and optimal conditions were acquired within a given range.

• 소성∙가공
• /
• 제17권7호
• /
• pp.528-533
• /
• 2008

Cavity in the mold is exposed to high pressure during injection molding operation. Injection molded articles with deep depth are often demanded as design variety increases. Subsequently mold becomes weak and deformation increases as the mold depth increases. Thus the injection molds for deep depth articles should be designed to hold out high pressure or stress concentration and large deformation. Through this study, equation for mold design was examined and suggested novel method to determine equation for mold design with deep depth. Novel equation developed in this study was modified from beam theory considering cantilever and two points bending situation while previous equation was modified from just cantilever bending situation. The validity of novel equation was verified through computer simulations for various mold side and wall thickness.

• Design & Manufacturing
• /
• 제7권1호
• /
• pp.40-44
• /
• 2013

My company develops, manufactures injection mold and produces thin-walled cosmetics and food containers. Without high quality and low production cost, it is hard to compete in the market. To be competitive, a company has to utilize mold with as many cavities as possible to lower manufacturing cost. Eject plate abrasion and deformation cut down mold lifespan, troubles during injection lower productivity and foreign substances in molds cause abrasion. This study focuses on how to improve mold life and productivity, and to slow down mold abrasion.

• 펄프종이기술
• /
• 제48권3호
• /
• pp.66-72
• /
• 2016

The applicability of rice husk fiber as a raw material for eco-friendly pulp mold was evaluated in this study. The higher demand of environmental friendly packaging material resulted in the more interest for the natural fiber based pulp mold. The rice husk which is an abundant agricultural byproduct in Asia could be defiberized by an alkaline digestion process. The changes in the pulp mold making process and the properties of pulp mold by the addition of the rice husk were investigated. The addition of rice husk fiber to the pulp mold made with OCC or UBKP resulted in the increase in drainage at the pulp mold forming process. In case of UBKP pulp mold, the addition of rice husk fiber increased the drying efficiency after pulp mold forming since the structure of pulp mold became more bulkier by the addition of the rice husk fiber. Those results showed the rice husk fiber could be applied to the pulp mold manufacturing as one of the eco-friendly natural fiber resources.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 가을학술발표대회논문집
• /
• pp.21-22
• /
• 2023

In order to manufacture high-quality free-form concrete panel (FCP), it is necessary to analyze the limitations of free-form silicone mold (FSM) and conduct technology development research. Currently, the FSM used in FCP manufacture is classified into a side silicon mold(SSM) and a lower silicon mold(LSM). In this study, the limitations of each silicon mold were analyzed and solutions were proposed. In the case of side silicon mold, there is a limit to cannot supporting the side pressure of concrete. Therefore, a mold stacking method was proposed, and at the same time, a process of correcting the movement value of the rod was proposed. In the case of the lower silicon mold, there is a limit to completely implementing the design shape. Therefore, a real-time scanning method and a process of displaying FCP shape coordinates were proposed. The results of this study are expected to be used as basic data for manufacturing high-quality FCP.

• 소성∙가공
• /
• 제8권3호
• /
• pp.289-289
• /
• 1999

This paper describes the investment casting of TiAl alloys. The effects of mold material and mold preheating temperature for the investment casting of TiAl on metal-mold interfacial reaction were investigated by means of optical micrography, hardness profiles and an electron probe microanalyzer. The mold materials examined were colloidal silica bonded ZrO₂, ZrSiO₄, A1₂O₃and CaO stabilized ZrO₂. When compared with conventional titanium a1loy, the high aluminum concentration of TiAl alloys helps to lower their reactivity in the molten state. The A1₂O₃mold is a promising mold material for the investment casting of TiAl in terms of the thermal stability, formability and cost. Special attention need to be paid to thermal stability and mold preheating when developing the investment calling of TiAl alloys.

• Design & Manufacturing
• /
• 제8권2호
• /
• pp.50-55
• /
• 2014

Recently, semi-stack mold have been developed for satisfying the various elements required in the mold industry. The mold is possible using with general-purpose injection molding machine by weight reduction through the improvement of the mold structure. In order to do that, tension core, spiral cooling system and half runner system were applied. It is effective for increased productivity and decreased of loss to the materials. However, the mold is required the filling balance in order to improve the quality and efficiency. Thus this study performed that optimum design and analysis of semi-stack mold for filling balance.

• Design & Manufacturing
• /
• 제6권2호
• /
• pp.90-95
• /
• 2012

The sheet metal forming proceccing is very important and indispensable in the automotive industry because the accuracy of prsee worked parts is directly related to the automotive quality. But when making mold it is difficult and expensive to modify mold. mold design technology is a critical technology in press plastic working. When design the mold there are lots of variables in press plastic working according to worked material, mold materials, conditions of heat treatment, clearance and so on. Abrasion of mold depends on these kind of conditions and sheared surface which is crucial for quality of product also depends on them. In this study, we conduct research on abrasion loss of mold according to 8, 10 and 12% of clearance for thickness of 1.0mm of worked material out of mold design variables of the products whose worked materials are high carbon steel and carbon tool steel by a practical experiment and perform a comparative evaluation of difference of abrasion loss mold with the alloy tool steel (STD11) and Tungsten Carbide (WC).