• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.5
• /
• pp.818-823
• /
• 2013

In the process of sterilization during the manufacture of beverages, both the treatment time and the temperature influence the beverage taste and flavor. Therefore, to improve the beverage quality, a nonthermal sterilization method is preferred to a high-temperature one. A nonthermal method, ultrasonic treatment by shock waves from cavitation, has been known to have a sterilizing effect. In this study, to observe the effect of ultrasonic frequency and treatment time on beverage quality, batch type ultrasonic equipment was fabricated and tested. Further, to evaluate the applicability of this ultrasonic method to an in-situ process, flow type ultrasonic heptagonal equipment was fabricated and then used to perform a sterilization experiment. Subsequently, the sterilizing effect was measured under ultrasonic and low-temperature ($55^{\circ}C$) treatments. Based on the obtained results, ultrasonic sterilization technology that can be applied for treatments at flow rates of up to 3 L/min was developed.

• Steel and Composite Structures
• /
• v.16 no.2
• /
• pp.187-201
• /
• 2014

A new through-beam connection system for a concrete filled steel tube column to RC beam is proposed. In this connection, there are openings on the steel tube while the reinforced concrete beams are continuous in the joint zone. The moment and shear force at the beam ends can be transferred to column by continuous rebar and concrete. The weakening of the axial load and shear bearing capacity due to the opening of the steel tube can be compensated by strengthening steel tube at joint zone. Using this connection, construction of the joint can be made more convenient since welding and hole drilling in situ can be avoided. Axial compression and reversed cyclic loading tests on specimens were carried out to evaluate performance of the new beam-column connection. Load-deflection performance, typical failure modes, stress and strain distributions, and the energy dissipation capacity were obtained. The experimental results showed that the new connection have good bearing capacity, superior ductility and energy dissipation capacity by effectively strengthen the steel tube at joint zone. According to the test and analysis results, some suggestions were proposed to design method of this new connection.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.365-371
• /
• 2004

Generally, fracture of a material is influenced by plastic zone size developed near the crack tip. Hence, according to the relative size of plastic zone in the material, the mechanics as a tool for analyzing the fracture process are classified into three kinds, that is, Linear Elastic Fracture Mechanics, Elastic Plastic Fracture Mechanics, Large Deformation Fracture Mechanics. Even though the plastic zone size is such an important parameter, the practical measurement techniques are very limited and the one for in-situ measurement is not virtually available. Therefore, elastic-plastic FEA has been performed to estimate the plastic zone size. In this study, it is noticed that side necking at the surface is a consequence of plastic deformation and lateral contraction and the relation between the plastic zone and side necking is investigated. FEA for modified boundary layer models with finite thickness, various mode mixities $0^{\circ}$, $30^{\circ}$, $60^{\circ}$, $90^{\circ}$ and strain hardening exponent n=3, 10 are performed. The results are presented and the implication regarding to application to experiment is discussed.

• Atmosphere
• /
• v.20 no.4
• /
• pp.519-530
• /
• 2010

In this paper we review current research on Atmospheric Brown Clouds (ABCs) with lightweight Unmanned Aerial Vehicles (UAVs) and miniaturized instruments. The UAV technology for in-situ measurements, including aerosol concentration, aerosol size distribution, aerosol absorption, cloud drop size distribution, solar radiation fluxes (visible and broadband), and spectral radiative fluxes, is a leading-edge technology for cost-effective atmospheric sounding, which can fill the gap between the ground measurement and satellite observation. The first experimental observation with UAVs in Korea, Cheju ABC Plume Monsoon Experiment (CAPMEX), conducted during summer 2008 revealed that the Beijing plumes exerted a strong positive influence on the net warming and fossil-fuel-dominated black-carbon plumes were approximately 100% more efficient warming agents than biomass-burning-dominated plumes. Long-term sustainable routine UAV measurements will eventually provide truly three-dimensional data of ABCs, which is necessary for the better understanding of their climate impacts and for the improvement of numerical models for air pollution, weather forecast and climate change.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.293-299
• /
• 2008

If a conventional type of Plastic Board Drain (PBD) is installed to the deep clay deposit, it is subjected to a high lateral earth pressure. a flow channel of PBD may be reduced by the collapse of cores and clogged by the intrusion of filter into the space between cores which are made by lateral pressure. It could decrease the ability of initial discharge capacity and the reliability of long term discharge capacity. A cylindrical plastic board drain (C-PBD) considered in this study consists of cylindrical core and several supports so that it can prevent the reduction of area of flow channel from the higher lateral earth pressure effectively. The discharge capacity of C-PBD was compared to that of a conventional PBD through performing experiments using the composite discharge capacity apparatus which can consider in-situ condition such as penetration of drains, ground settlement and discharge capacity. As a result, C-PBD showed much better performance than PBD in the ability of discharge. It was observed that the C-PBD was folded whereas the conventional PBD was folded after the experiment.

• Journal of Korean Society for Atmospheric Environment
• /
• v.26 no.4
• /
• pp.380-391
• /
• 2010

Airborne in-situ measurements of aerosol/cloud number concentrations were analyzed to investigate the effects of aerosols on warm cloud formation in the Pacific Dust Experiment (PACDEX) during April and May 2007. In the air masses originating from the Asian continent, high concentrations of fine particles including black carbon (BC) were observed when compared to other regions. A strong correlation (r=0.88) between condensation nuclei (CN) having sizes ranging from 0.1 to 1.0 mm ($CN_{0.1-1.0}$) and cloud condensation nuclei (CCN) at 0.4% supersaturation ($CCN_{0.4%}$) suggests that most of the $CN_{0.1-1.0}$ can contribute to cloud formation. The possibility of a cloud droplet formation by BC particles was expected at the high water vapor mixing ratio (WVMR) and the abundance of water-soluble components at the low altitude less than 3 km.

• Macromolecular Research
• /
• v.13 no.2
• /
• pp.156-161
• /
• 2005

The thermal transitions of a nylon 6/layered silicate nanocomposite were studied by differential scanning calorimetry and in-situ synchrotron X-ray diffraction. The drawn film of the nylon 6/layered silicate nanocomposite typically showed three endotherms in the DSC thermogram; a very broad endotherm at $\sim120^{\circ}C(T_{1})$, a double-melting endotherm at $\sim215^{\circ}C(T_{2})$, and a high temperature endotherm at $\sim240^{\circ}C(T_{3})$. The drawn film of the nylon 6/ layered silicate nanocomposite was comprised of a mixture of the $\alpha and \gamma$ forms, with $the \alpha form$ being generated by drawing the pressed film having $the \gamma form$. The melting and crystallization of the crystals were observed at the above thermal transitions during the heating experiment performed at the Pohang X-ray synchrotron radiation source (4C2). The newly generated form was meta-stable and melted $at {\sim}T_{1}$. The double-melting $at {\sim}T_{2}$ was due to the exothermic crystallization of $the \alpha form$ during the main endothermic melting of $the \gamma form$. $The \alpha form$ crystallized $at {\sim}T_{2}$ and melted $at {\sim}T_{3}$.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.238-238
• /
• 2006

Through ultra-violet photoemission spectroscopy in-situ experiment, 0.67 eV energy barrier between 1-hexadecanethiol (HDT)-modified gold and pentacene was observed, which was 0.03 eV smaller than the energy barrier between bare gold and pentacene despite HDT modified gold had 0.8 eV lower work function than that of bare gold. This result is opposed to the idea that increasing the work function a metal decreases the energy barrier. This can be explained by two factors. One is the absence of interface dipole, which is observed in pentacene deposited on gold. The other is reduced ionization energy which can be explained through polarization energy or electronic splitting of molecular orbital with more crystalline structure observed through X-ray diffraction patterns.

• Korean Journal of Chemical Engineering
• /
• v.35 no.11
• /
• pp.2191-2197
• /
• 2018

To remove tar and produce environment-friendly $H_2$, one of the promising routes is the sorption-enhanced steam reforming (SESR) process, in which the $CO_2$ sorbent is a key element. We prepared the $CO_2$ sorbents with $Ca_{12}Al_{14}O_{33}$ as carrier with various methods. Their characterizations were examined, and the sample prepared by solgel (SG) method showed the strongest CaO and $Ca_{12}Al_{14}O_{33}$ phases and the most excellent pore structure among all the samples. Then, a thermogravimetric experiment was conducted, and the results showed that the sample prepared by sol-gel (SG) method had the best $CO_2$ adsorption capacity and excellent long-term cyclic stability. Finally, the sorbent was used into the steam reforming experiments of tar. Under the action of the sorbent, the reforming reaction was enhanced in-situ, with the $H_2$ yield and concentration improved obviously, and especially, $H_2$ concentration can reach over 98.85%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.116-119
• /
• 2003

[ $Hg_{1-x}Cd_xTe$ ] (MCT) was grown by hot wall epitaxy method. Prior to the MCT growth, the CdTe (111) buffer layer was grown on the GaAs substrate at the temperature of 590 C for 15 min. When the thickness of the CdTe buffer layer was 5 m or thicker, the full width at half maximum values obtained from the x-ray rocking curves were found to significantly decrease. After a good quality CdTe buffer layer was grown, the MCT epilayers were grown on the CdTe (111) /GaAs substrate at various temperature in situ. The crystal quality for those epilayers was investigated by means of the x-ray rocking curves and the photocurrent experiment. The photoconductor characterization for the epilayers was also measured. The energy band gap of MCT was determined from the photocurrent measurement and the x composition rates from the temperature dependence of the energy band gap were turned out.