• Journal of the Korean GEO-environmental Society
• /
• v.13 no.11
• /
• pp.11-17
• /
• 2012

This study focused on application of various $CO_2$ philic adsorbents with amine to improve $CO_2$ uptake in mortar. TGA, phenolphthalein method, FT-IR XRD, and FE-SEM analysis methods were used to evaluate $CO_2$ capture in mortar. When $CO_2$ philic adsorbents was used, $CO_2$absorption efficiency was improved maximum of 58.5%. Carbonation depth was increased 3 times compared with original mortar. Chemical reactions between bicarbonate ion, $CO_2$, $CO_2$ philic adsorbents aqueous solution, and $Ca^{2+}$ ions dissolved from cement formed $CaCO_3$ in the mortar. Therefore, impregnation of the $CO_2$ philic adsorbent on the surface of the mortar can increase the adsorbed $CO_2$.

• Carbon letters
• /
• v.24
• /
• pp.62-72
• /
• 2017

The aim of this work was to evaluate the dielectric properties of impregnated and activated palm kernel shells (PKSs) samples using two activating agents, potassium carbonate ($K_2CO_3$) and sodium hydroxide (NaOH), at three impregnation ratios. The materials were characterized by moisture content, carbon content, ash content, thermal profile and functional groups. The dielectric properties were examined using an open-ended coaxial probe method at various microwave frequencies (1-6 GHz) and temperatures (25, 35, and $45^{\circ}C$). The results show that the dielectric properties varied with frequency, temperature, moisture content, carbon content and mass ratio of the ionic solids. PKSK1.75 (PKS impregnated with $K_2CO_3$ at a mass ratio of 1.75) and PKSN1.5 (PKS impregnated with NaOH at a mass ratio of 1.5) exhibited a high loss tangent ($tan{\delta}$) indicating the effectiveness of these materials to be heated by microwaves. $K_2CO_3$ and NaOH can act as a microwave absorber to enhance the efficiency of microwave heating for low loss PKSs. Materials with a high moisture content exhibit a high loss tangent but low penetration depth. The interplay of multiple operating frequencies is suggested to promote better microwave heating by considering the changes in the materials characteristics.

• Applied Chemistry for Engineering
• /
• v.10 no.7
• /
• pp.1003-1007
• /
• 1999

The activity and products distribution for the hydrogenation of butadiene and pentadiene over the gold and cobalt catalysts prepared by coprecipitation and impregnation method was investigated with using a flow reactor under atmospheric pressure. The reaction characteristics of the highly dispersed gold particles and its role were studied. The activity of the gold catalyst by coprecipitation was much higher than that by impregnation. The selectivity of butene on all gold particles was always 100% even in the absence of butadiene in the stream, but butadiene on cobalt supported catalyst was easily hydrogenated to butane. It was therefore considered that the active sites at circumferences of the gold particles possessed an unique property which took a proper affinity to hydrogen. In the hydrogenation of butadiene and pentadiene, the percentages of 1-butene and 2-pentene were 60%~70% and about 62%, respectively. The results could be simply explained by a statistical concepts of hydrogen addition.

• Journal of Mechanical Science and Technology
• /
• v.14 no.3
• /
• pp.320-330
• /
• 2000

It is desirable to perform nondestructive evaluation (NDE) to assess material properties and part homogeneity because the manufacturing of carbon/carbon brake disks requires complicated and costly processes. In this work several ultrasonic techniques were applied to carbon/carbon brake disks (322mm ad, 135mm id) for the evaluation of spatial variations in material properties that are attributable to the manufacturing process. In a large carbon/carbon disk manufactured by chemical vapor infiltration (CYI) method, the spatial variation of ultrasonic velocity was measured and found to be consistent with the densification behavior in CYI process. Low frequency (e.g., 1-5MHz) through-transmission scans based on both amplitude and time-of-flight of the ultrasonic pulse were used for mapping out the material property inhomogeneity. Images based on both the amplitude and the time-of-flight of the transmitted ultrasonic pulse showed significant variation in the radial direction. The radial variations in ultrasonic velocity and attenuation were attributed to a density variation caused by the more efficient densification of pitch impregnation near the id and od and by the less efficient densification away from the exposed edged of the disk. Ultrasonic velocities in the edges of the disk. Ultrasonic velocities in the thickness direction were also measured as a function of location using dry-coupling transducers ; the results were consistent with the densification behavior. However, velocities in the in-plane directions (circumferential and radial) seemed to be affected more by the relative contents of fabric and chopped fiber, and less by the void content.

• Nuclear Engineering and Technology
• /
• v.5 no.2
• /
• pp.103-114
• /
• 1973

Radiation grafting of acrylic acid and 4-vinylpyridine at room temperature has been studied by an impregnation method to improve the hygroscopic properties, the antistatic behavior and the dyeability of polyester fabric. Polyester fabric was impregnated with acrylic acid or aqueous emulsion of acrylic acid-4-vinylpyridine by immersion at 25$^{\circ}$or 7$0^{\circ}C$. The impregnated fabric was irradiated under nitrogen gas with ${\gamma}$-rays from Co-60. When acrylic acid grafted polyester fabric was treated with sodium carbonate, calcium acetate and potassium persulfate, tne rate of water absorption was increased and most parts of polyacrylic acid formed were extracted off from the fabric with 0.1% solution of sodium hydroxide at 10$0^{\circ}C$. In the case of the impregnation of a mixture of acrylic acid and 4-vinylpyridine the petcent of grafting has been shown to be proportional to the ratio of 4-VP/AA and radiation dost. Estimating by contact angle measurements of water on the various polymer surfaces, the antistatic behavior was decreased with the increase of grafting percent. The investigation of electron micrograph disclosed the existence of certain type of discontinuities in the acrylic acid grafted polyester fiber which was treated with various salts.

• Clean Technology
• /
• v.13 no.2
• /
• pp.99-103
• /
• 2007

Pt/Nafion self-humidifying membranes for Polymer Electrolyte Membrane Fuel Cell (PEMFC) were synthesized via a supercritical-impregnation method. The Nafion 112 membranes were impregnated with Pt(II) acetylacetonate from a supercritical carbon dioxide ($scCO_2$) solution at $80^{\circ}C$ and 19.8 MPa. After the impregnation, the Pt-impregnated Nafion membrane was converted Pt deposited Nafion(Pt/Nafion) membrane by reducing agent, sodium borohydride ($NaBH_4$) under $50^{\circ}C$ and 2 hours. The prepared Pt/Nafion membranes were investigated by SEM, EDS and EPMA. The performance of the Pt/Nafion membranes was examined in PEMFC as a self-humidifying membrane. The cell performance of the Pt/Nafion membrane at $65^{\circ}C$ is better than that of Nafion 112.

• Polymer(Korea)
• /
• v.33 no.6
• /
• pp.575-580
• /
• 2009

Carbon fabric-reinforced silicon carbide composites (C/SiC) have attracted a considerable attention for high temperature structural application because of their outstanding oxidation resistance property and thermal shock resistance. In this study, we reported on the preparation of C/SiC composites by the polymer impregnation and pyrolysis (PIP) method. For this, polycarbosilane solution was impregnated into the carbon fabric and then cured by electron beam irradiation under argon atmosphere. Afterwards, the cured composite was pyrolyzed at $1300^{\circ}C$ for 1 h under argon atmosphere to produce the C/SiC composite. The porosity and density of the C/SiC composite were 13.5% and $2.44\;g/cm^3$, respectively, when the impregnation of the carbon fabric with the 30 wt% polycarbosilane solution conducted four times. In addition, in the isothermal experiment at $1500\;^{\circ}C$ in air for 5 h, the 95.9 wt% of the C/SiC composite was remained, indicating that the prepared C/SiC composite has a outstanding oxidation resistance.

• Korean Journal of Materials Research
• /
• v.24 no.5
• /
• pp.243-248
• /
• 2014

Silicon-carbon composite was prepared by the magnesiothermic reduction of mesoporous silica and subsequent impregnation with a carbon precursor. This was applied for use as an anode material for high-performance lithium-ion batteries. Well-ordered mesoporous silica(SBA-15) was employed as a starting material for the mesoporous silicon, and sucrose was used as a carbon source. It was found that complete removal of by-products ($Mg_2Si$ and $Mg_2SiO_4$) formed by side reactions of silica and magnesium during the magnesiothermic reduction, was a crucial factor for successful formation of mesoporous silicon. Successful formation of the silicon-carbon composite was well confirmed by appropriate characterization tools (e.g., $N_2$ adsorption-desorption, small-angle X-ray scattering, X-ray diffraction, and thermogravimetric analyses). A lithium-ion battery was fabricated using the prepared silicon-carbon composite as the anode, and lithium foil as the counter-electrode. Electrochemical analysis revealed that the silicon-carbon composite showed better cycling stability than graphite, when used as the anode in the lithium-ion battery. This improvement could be due to the fact that carbon efficiently suppressed the change in volume of the silicon material caused by the charge-discharge cycle. This indicates that silicon-carbon composite, prepared via the magnesiothermic reduction and impregnation methods, could be an efficient anode material for lithium ion batteries.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.25 no.8
• /
• pp.432-437
• /
• 2013

The increase of greenhouse gas emission and decrease of fossil fuel are being caused by the indiscreet consumption of energy by people. Recently, green policy has been globally implemented to reduce energy consumption. This paper studied the research to reduce the energy consumption in buildings, by using the heat storage properties of PCM. PCM has to prevent leakage from the liquid state. Therefore, we prepared form stable PCM, by using the vacuum impregnation method. Three kinds of organic PCMs were impregnated into the structure of porous material. The characteristics of the composites were determined by using SEM, DSC, FTIR and TGA. SEM morphology showed the micro structure of silica fume/PCM. Also, thermal properties were examined by DSC and TGA analyses; and the chemical bonding of the composite was determined by FTIR analysis.

• Composites Research
• /
• v.34 no.1
• /
• pp.1-7
• /
• 2021

Fiber-reinforced thermoplastic composites are applied to transport industries to lightweight of body, and applications will be expanded gradually. In this study, the impregnation and mechanical properties of continuous glass fiber (GF) reinforced polycarbonate (PC) composites were evaluated with different molecular weights of PC. The continuous GF reinforced PC composite were prepared by using GF fabric and PC film via continuous compression molding method. The melting flow index and tensile strength of PC matrix were evaluated with different molecular weights. Mechanical properties (tensile, flexural, and compressive) and pore rate of GF/PC composite were evaluated with different molecular weights of PC. The fracture behavior was analyzed to fracture surface of GF/PC composite using FE-SEM images. As these results, it was condition of representing the best mechanical property that the GF/PC composite was prepared by using PC of 20,000 g/mol as matrix.