• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.663-666
• /
• 2003

Using numerical analysis modeling of Multi-electrode Array that could be applied to the corrosion state measurement of a reinforcing steel bar in concrete, the steel bar location inside concrete can be probed by the investigation of the change of the measured impedance from concrete surface determined by the electrical impedance of interface between the steel bar and concrete, the electrical resistivity of concrete, the array of electrodes and the relative location and diameter of the steel bar.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2000년도 춘계학술대회 논문집
• /
• pp.116-122
• /
• 2000

This paper presents a simulation method with constant power model for the train load. In power system simulation loads could be modeled as a constant power, constant current, constant Impedance or a function of voltage and frequency. At this time, however, representing a train load as the function is difficult because of the lack of data. Therefore as a first step, simulation method with a constant power model fer a train is studied, and the test result is compared with the simulation result using the constant Impedance model.

• 한국음향학회지
• /
• 제28권4호
• /
• pp.363-369
• /
• 2009

본 논문에서는 인접된 다중모드 공진점을 갖는 수중 음향 압전 트랜스듀서의 전기적 등가회로 모델을 추정하는 방법을 제안하였다. 트랜스듀서의 실측된 임피던스와 추정된 등가모델의 임피던스 오차가 최소가 되도록 공진모드간 결합 영향을 고려한 적합도 함수를 제안하고, 미립자 집단 최적화 (PSO:Particle Swarm Optimization) 알고리즘을 이용하여 등가회로의 미지상수를 추정하였다. 3개의 공진점을 갖는 샌드위치형 예제 트랜스듀서에 대하여 제안된 방법을 적용하여 등가회로를 모델링하고, 수중에서의 임피던스 측정치와 추정된 등가모델의 임피던스를 비교함으로써 제안된 기법의 타당성을 검증하였다.

• Environmental Engineering Research
• /
• 제23권2호
• /
• pp.164-174
• /
• 2018

Corrosion of copper alloys (copper, bronze and brass) in soil was evaluated at ambient temperature using various methods such as electrochemical impedance spectroscopy (EIS), polarization curves and Scanning Electron Microscopy (SEM) coupled with Energy Dispersive Spectroscopy microanalysis measurements. Three equivalent circuits were separately used to interpret the obtained impedance spectra. The EIS measurements indicated that the polarization resistance of all electrodes increases with increasing the immersion time. SEM showed a presence of three layers of corrosion products with various composition and morphology covering each electrode. In addition, it was found that at 20% of moisture content the $R_p$ values and the current density of all electrodes in the studied soil give the following order: copper > bronze > brass. Good consistency between the data obtained from EIS and PP measurements was observed.

• 한국컴퓨터산업학회논문지
• /
• 제7권5호
• /
• pp.563-572
• /
• 2006

피부를 통한 최적의 광투과 치료방식은 국소병변에 직접적으로 광을 조사할 수 있는 장점을 가지나 피부의 가장 바깥 부분인 각질부의 다양한 피부색상으로 인해 광전달 능력에 차이가 있고 다양한 환자에 따라 치료가 부적절 할 수가 있다. 본 연구에서는 피부 임피이던스에 따른 광조사 방식에 따른 일정한 측정을 하기 위해 피부 임피이던스 방식과 피부영역 추출을 통해 색상정보와 차영상을 이용한 방법 즉, 색상정보를 이용한 HIS와 YIQ의 성분이 가장 보편적인데 실험에서는 피부색상에 해당하는 각 색상성분을 탐색한 다음, 색상정보를 이용한 결과로 환자의 피부모델 영역검출에 따라 결과를 영상정보를 통해 개개인의 피부모델을 자동적으로 생성, 측정하여 피부색깔, 에너지, 파장, 폭, 조사시간, 펄스지연 등을 추출하여 원하는 최적의 모델과 특성을 조사하며, 피부 임피이던스에 따른 병변치료 펄스모델링의 기준을 구하였고, 피부부하에 따른 최적의 광조사 펄스모델링 시스템을 설계하여 제작하여, 피부칼라에 따른 적절한 치료펄스 데이터베이스를 구축하였다.

• Smart Structures and Systems
• /
• 제4권1호
• /
• pp.35-46
• /
• 2008

In this paper the authors address the problem of comparing two different smart damping techniques using the numerical modelling of the electro-mechanical impedance for plate structures partially treated with active constrained layer damping treatments. The paper summarizes the modelling procedures including a finite element formulation capable of accounting for the observed behaviour. The example used is a smart cantilever plate structure containing a viscoelastic material (VEM) layer sandwiched between a piezoelectric constrained layer and the host vibrating plate. Comparisons are made between active constrained layer and active damping only and based on the resonance frequency amplitudes of the electrical admittance numerically evaluated at the surface of the piezoelectric model of the vibrating structure.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.1022-1025
• /
• 2008

To the best of our knowledge, for the first time, we applied impedance spectroscopy to analysis on OLED degradation mechanism by monitoring impedance change during constant voltage aging, and modeling OLED with lumped circuit elements. Change in each element value was used to explain charge accumulation and field redistribution in each organic layer.

• 전자공학회논문지A
• /
• 제32A권3호
• /
• pp.110-117
• /
• 1995

New formulas for the minimum noise figure and the optimum source impedance of microwave FETs are derived using the noise equivalent circuits obtained from the steady-state Nyquist theorem for multi-terminal semiconductor devices. The derived formulas manifest the relationships between the noise sources and the physical parameters of a noise equivalent circuit. Furthermore the formulas can explain the effect of gate leakage current on the minimum noise figure and the optimum source impedance. comparisons with the published experimental data confirm the validity and usability of our formula.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제52권4호
• /
• pp.246-251
• /
• 2003

This paper proposes a new methodology for the estimation of impedance characteristics, which is one of the important issue in the power distribution network design of printed circuit boards. The modeling process of the proposed method divides the power distribution network into uniform segment, and each segment is modeled by distributed RLC transmission lines. Then, for the efficient computation of impedance characteristics in frequency domain. the proposed method uses a model-order reduction method.

• 전자공학회논문지A
• /
• 제29A권3호
• /
• pp.25-32
• /
• 1992

In UHF, VHF new design method of samll-sized 3-dB 0$^{\circ}$/180$^{\circ}$ ring hybrid terminated arbitrary impedance using both lumped elements and distributed elements is presented. At the center frequency of 900 MHz, 3-dB 0$^{\circ}$/180$^{\circ}$ ring hybrid terminated arbitrary impedance is designed, analyzed and tested. Good agreements are obtained between measured and theoretical modeling results, and at the same time, the circuit area of hybrid fabricated with two dimensional parallel coupled line, distributed elements and lumped elements is reduced by more than 70% compared with only distribyted-type circuits.