• Corrosion Science and Technology
• /
• v.16 no.4
• /
• pp.175-182
• /
• 2017

Galvanic current measurement, polarization curves, electrochemical impedance spectroscopy and weight loss test were used to study the corrosion behavior of carbon steel before and after carbon fibers coupling to the carbon steel in simulated concrete pore solutions, and the film composition on the steel surface was analyzed using XPS method. The results indicate that passive film on steel surface had excellent protective property in pore solutions with different pH values (13.3, 12.5 and 11.6). After coupling with carbon fibers (the area ratio of carbon steel to carbon fiber was 12.31), charge transfer resistance $R_{ct}$ of the steel surface decreased and the $Fe^{3+}/Fe^{2+}$ value in passive film decreased. As a result, stability of the film decreased and the corrosion rate of steel increased. Decreasing of the area ratio of steel to carbon fiber from 12.3 to 6.15 resulted in the decrease in $R_{ct}$ and the increase in corrosion rate. Especially in the pore solution with pH 11.6, the coupling leads the carbon steel to corrode easily.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.10
• /
• pp.74-79
• /
• 2010

In this paper, a high gain W-band amplifier is presented using 70 run mHEMT MMIC technology. The length of source feedback line of common-source FET is carefully determined to maximize the gain at a design frequency. Simulation shows that MAG can be increased by 0.8 dB by optimizing the length of this line. In addition, this feedback line changes the input impedance of the common-source FET in a way that the input match can be made easier. In this work, 4-stage amplifier is designed on CPW using the source feedback. The measurement shows the excellent gain performance higher than 22.0 dB across 70~103 GHz.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.1
• /
• pp.155-161
• /
• 2007

This paper presents the design simulation, implementation, and measurement of a miniaturized PCS / Satellite DMB dual-band stacked mompole antenna with a parasitic patch for mobile communication terminals. A stacked helix is realized by using a via hole with height of 0.4 mm and a diameter of 0.35 mm to connect upper- and lower-layer helix sections for a reduction of the dimensions of the antenna. In addition the stacked helix chip antenna is interleaved with a parasitic patch to achieve two different radiation modes. The ratio of the first frequency and the second frequency vary with the geometrical parameter of the parasitic patch. The fabricated antenna uses FR-4 substrate with a relative permittivity of 4.2. Its dimensions are $15.5{\times}7.6{\times}0.4 mm^3$. The measured impedance bandwidths (VSWR<2) are 240 and 250 MHz at the operating frequencies, respectively.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.5
• /
• pp.629-636
• /
• 2011

This paper presents the design of a novel integrated T-DMB/GPS/Mobile antenna for vehicular application. The T-DMB antenna is designed with a modified meander-type microstrip patch providing linearly a polarized broadside radiation pattern. The GPS antenna is designed with an inserted slot in the patch antenna providing circularly polarized broadside radiation pattern. The Mobile (GSM, AMPS, DCS, PCS, UMTS, etc.) antenna is designed as a modified G-type patch antenna providing multi-band operation. Experimental results indicate that the impedance bandwidth (VSWR 1:2.5) of the proposed T-DMB /GPS/Mobile antenna satisfactorily matches that of the simulation results. The 2D and 3D radiation patterns and gains according to the results of the experiment are also presented and discussed.

• Journal of the Korean Electrochemical Society
• /
• v.18 no.3
• /
• pp.130-135
• /
• 2015

The rate capability and low-temperature characteristics of graphite electrode are investigated after surface treatment with copper phthalocyanine (CuPc) or phthalocyanine (Pc). Uniform coating layers comprising amorphous carbon or copper are generated after the treatment. The rate performance of graphite electrodes is enhanced by the surface treatment, which is more prominent with CuPc. The resistance of the graphite electrode estimated from electrochemical impedance spectroscopy and pulse resistance measurement is the smallest for the CuPc-treated graphite. It is likely that the amorphous carbon layer formed by the decomposition of Pc facilitates $Li^+$ diffusion and the metallic copper derived from CuPc improves the electrical conductivity of the graphite electrode.

• Journal of Electrochemical Science and Technology
• /
• v.8 no.1
• /
• pp.43-52
• /
• 2017

In this paper, for the first time, the electroanalytical study of Triethylenediamine, TEDA was done on a typically graphene modified carbon paste electrode (Gr/CPE) in pH=10.5 of phosphate buffer solutions (PBS). The surface morphology of the bare and modified electrodes was characterized by scanning electron microscopy (SEM), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The electro-oxidation of TEDA was investigated at the surface of modified electrode. The results revealed that the oxidation peak current of TEDA at the surface of Gr/CPE is 2.70 times than that shown at bare-CPE. A linear calibration plot was observed in the range of 1.0 to 202.0 ppm. In this way, the detection limit was found to be 0.18 ppm. The method was then successfully applied to determination of TEDA in aqueous samples obtained from two kinds of activated carbon from the masks of war. On the other hand, density functional theory (DFT) method at B3LYP/6-311++G** level of theory and a conductor-like Polarizable Continuum Model (CPCM) was used to calculate the $pK_a$ values of TEDA. The energies of lowest unoccupied molecular orbital ($E_{LUMO}$) and highest occupied molecular orbital ($E_{HOMO}$), gap energy (${\Delta}E$) and some thermodynamic parameters such as Gibbs free energy of TEDA and its conjugate acid ($HT^+$) were calculated. The results of calculated $pK_a$ were found to be in good agreement with the experimental values.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.4
• /
• pp.513-520
• /
• 2001

In this paper, the directional coupler using three layer microstrip substrate is proposed and the design method is notified. Modified re-entrant mode coupler is the proposed structure that one layer is added on upper plane of coupled transmission lines and the floating conductor is placed on added layer's upper planes. This structure has high coupling for the increase of odd mode capacitance and also has good performance in VSWR, isolation, phase difference because the difference of effective permittivity is small in each mode. We have designed the coupler from the calculation of impedance, effective permittivity, coupling coefficient using even, odd mode analysis method. From the simulation and measurement, proposed coupler has about 2 dB more tighter coupling than conventional coupler and also has good performance in VSWR, isolation, phase difference.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.4
• /
• pp.473-482
• /
• 1998

In this paper, characteristics of the wide band microstrip antennas with parasistic element are analyzed by the Finite Difference Time Domain(FDTD) method, and antenna parameters are optimized to get maximum bandwidth, retern loss, input impedance, and radiation pattern are calculated by Founier transforming the time domain results. The characteristics of the antenna are varied and the bandwidth of the antenna is broaded as a length and a width of the driven element, a gap of the driven element and the parasitic element, a width and a length of parasitic element. So the different patchs are resonating at different frequencies and this multipule resonance increase the bandwidth. The Results of the calculation and measurement, the size of the antenna with parasitic element is about a twice larger than a microstrip antenna, but bandwidth is four times better than a microstrip antenna. And these results were in relatively good accordance with the measured values.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.368-371
• /
• 2020

In this paper, we propose a linear tapered slot rectifying antenna for a portable UHF-band RFID system. Since the proposed rectifying antenna does not use a dielectric substrate, the planar antenna is implemented with a thin metal thickness. The rectifier circuit converts input RF power into output DC voltage using a voltage doubler circuit based on two anti-parallel schottky diodes. The rectifying antenna is integrated by the voltage doubler circuit into a linear tapered slot antenna. For conjugate impedance matching of the rectifying circuit and the linear tapered slot antenna, the source-pull method was utilized by adjusting the angle of the tapered slot and the length of the antenna feed line. The proposed antenna prototype has been verified with the electrical and radiation characteristics through RF-DC conversion and far-field radiation test in open space measurement environment. Finally, the proposed antenna is realized to 0.23-wavelength (75 mm) and 0.18-wavelength (60 mm) at 915 MHz center frequency.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.12
• /
• pp.791-795
• /
• 2016

The effects of $TiO_2$ addition on the electrical insulation of AlN ceramics with 1 wt% $Y_2O_3$ as a sintering aid have been investigated. Some of $TiO_2$ has reacted with AlN powders and transformed to fine TiN particles during sintering, which was uniformly dispersed along grain boundaries of AlN. At a high electrical field (500 V/mm), the resistivity of AlN ceramics with $TiO_2$ addition of 0.2 wt% increased about 1000 times from $3{\times}10^{10}{\Omega}cm$ to $3.1{\times}10^{13}{\Omega}cm$. Based on the impedance spectroscopy measurement, it was found that $TiO_2$ addition increased dramatically electrical resistivity of AlN grains much more than that of grain boundaries. Thus, $TiO_2$ was believed to dissolve inside AlN grains to suppress ionic conduction of Al vacancies. This suppressed ionic conduction by Ti incorporation into AlN grains seems to contribute to more electrically insulating AlN ceramics.