• Journal of the Korea Fashion and Costume Design Association
• /
• v.12 no.4
• /
• pp.43-59
• /
• 2010

In the first half of 20th century, there was an abrupt change in society and social values. Therefore, a demand for functional women's sportswear started to increase. This paper has attempted to investigate the impact of functionalism on women's sportswear in the first half of the 20th century. The following results were obtained: First, anti-tradition was observed. There was a tendency to be separated from the past and against tradition. It was tried to pursue freedom, getting away from corset and petticoat. Second, structural functions were targeted. In other words, precise and efficient shapes and simple silhouette and line were emphasized. Third, fitness of purpose was found. More liberal and comfortable design has been targeted. That's why a variety of functional pants have been designed instead of skirts. Fourth, utility and practicality were found. Elastic fabrics such as wool and jersey and sweater have commonly used in sportswear. A variety of new fabrics have been used and details such as flare, slit and pleats have been designed. Lastly, non-ornamentality was found. The beauty of simple shape was pursued by omitting details or eliminating unnecessary ornaments. Monochrome and dark color were preferred and a use of accessories has declined. The result of this paper could be used in establishing a theoretical framework on the impact on social change, values and art and helpful In modern women's sportswear design and marketing which have become more important.

• Journal of the Korean Society for Heat Treatment
• /
• v.35 no.6
• /
• pp.303-313
• /
• 2022

The purpose of this study was to test and analyze the effects of the mechanical properties and structural changes of the austenitized and tempered martensite STS 410 stainless steel containing 11.5~13%Cr and 0.10%C on its temper embrittlement. The STS 410 stainless steel test pieces for each 3 hours at 960℃, 1000℃ and then, tempered them for 2 hours at 300℃, 350℃, 400℃, 450℃, 500℃, 550℃, 600℃, 650℃ and 700℃ known as the intervals vulnerable to temper embrittlement to observe the changes of their structures and mechanical properties. In case autenitizing was insufficient due to lower temperature of thermal treatment for solution, unsolved carbides and ferrites remained in the structure after quenching, which meant that the parts could wear out and corrode to embrittle at the room temperature. Elongation and impact energy changes with Tempering conditions showed minimum results in range of 400~500℃. The decrease in elongation and impact energy at 400~500℃ was the hardening effect of the subgrain due to the precipitation of many M₃C or M₇C₃, M₂₃C₆. And STS 410 stainless steel corrosion tested in 10% NaCl solution at 30℃ after tempering treatment. The degree of corrosion sensitization showed increasing tendency with increase of tempering temperature and Cr carbide precipitation were observed in grain boundary.

• Journal of the Korean Ceramic Society
• /
• v.47 no.3
• /
• pp.232-236
• /
• 2010

In recent years abrasive water jet (AWJ) has received significant attention as a technology used in the manufacturing industry for cutting materials. In this paper we report the development of a new preparation method of abrasives for water jet by using an air bubbling sedimentation rate control technique. The SiC abrasives prepared by an air bubbling sedimentation rate control technique using latex resin are found to be superior to the conventional abrasives not only in surface roughness uniformity but also in lifetime. The AWJ test results also show that the former has also better impact-resistance and wear-resistance than the latter.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1007-1011
• /
• 2004

Safety-Shoes are developed for heavy industry. Nowadays with the development of industry, it is increase on all of industry field. Safety-Shoes are to be classified into using intention. And it's developed not only protect from danger but also more comfort wearing. When wear a safety shoes, in cold weather, serious disease could be occur such as frostbitten and so on. In the study replaces steel toe-cap by polymer. Moreover add keeping warm, light weighting, chemical-proof. So we develop plastic Toe-Cap using plastic technology. And result of material property tess considered plastic to be using light work Safety Shoes Toe-Cap.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.04a
• /
• pp.48-52
• /
• 2004

Ultrasonic machining is effective for machining of extreme hard and brittle materials, including glass, ceramic, carbide, graphite. The major machining principle involves the direct hammering as well as the impact of abrasive panicles on the workpiece. Also, it involve cavitation erosion. The general workpiece is flat side. This study attempted micro hole machining of a curved surface of glass tube. Ultrasonic machining is fault of the slow machining speed. An experiment does and got 16 seconds validity machining time as increasing the processing speed. Moreover, entrance crack and surface roughness was similar both machining speed is slow and fast. Several micro hole of glass tube machined using one micro tool, but tool wear is infinitesimal.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.1
• /
• pp.42-51
• /
• 1998

A 150 m$\^$3//hr, 30 kg/cm$\^$2/, air-cooled 3-stage reciprocating air compressor is designed to be used in starting large diesel engines of ships. A basic design procedure is presented to meet the targeted pressure and flow rate, and especially a volumetric efficiency of 80%. Temperature and stress analysis of the 1st stage cylinder are performed using axisymmetric FEM modelings. The dynamics of valve system is analyzed and stress at the 1st stage valve seat caused by valve impact is evaluated. To reduce friction loss and wear at the compressor engine system tribological design issues are reviewed and good design practices are suggested. Finally, forced-air pin-type interstage coolers are designed to dissipate generated compression heat at each stage.

• Journal of the Speleological Society of Korea
• /
• no.71
• /
• pp.13-17
• /
• 2006

New methods of nano sized material and composite coating preparations have been considered on the base of mathematical model of abrasion reaction interaction of milling and grinding bodies in planetary centrifugal mill. The essence of the method is the abrasive and oxidative wear of the milling bodies and amorphous (better inert) additives. Interactions between them has been supplied the necessary impulse of pressure and temperature on the impact frictional contacts and promoted chemical processes. The offered method can find application for such processing as sintering and geological minerals opening.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.3
• /
• pp.114-122
• /
• 2002

Electric conductivities, mechanical properties and friction properties were investigated far graphite-nylon composites impregnated with oil. Specific resistivity of composites containing oil from 2% to 6% were in the range of $10^7 ~10^6 \ohm$ cm, which were applicable for anti-static purpose of composites improved by the impregnation of graphite with 2%. Improvement in the impact strength and friction properties of graphite/nylon composites was achieved by the impregnation of oil. The coefficient of friction of the composites containing graphite from 2% to 4% and oil with 2 - 4% showed much loller than that of virgin nylon. Also the abrasive wear of the oil impregnated graphite composites were decreased about 1/3 - 1/10.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.4
• /
• pp.24-29
• /
• 2017

This paper provides an experimental analysis on the breakage of the coated tool using the face-milling cutter of the machining center due to changes in the cutting speed and the feed rate. The experimental studies were conducted using STS 304 materials and the damage to the tool was analyzed according to the change in machining time. The experiments confirmed that the cutting speed and feed rate affected the tool damage and the mechanical impact and thermal shock were determined to severely damage the tool. From the production engineering point of view, it has been experimentally investigated that the increased feed rate significantly influences the material removal rate more than the increased cutting speed.

• Asia-Pacific Journal of Business
• /
• v.2 no.2
• /
• pp.1-35
• /
• 2011

Facing information overload in today's complex environments, managers look to a concise set of marketing metrics to provide direction for marketing decision making. While there have been several papers dealing with the theoretical aspects of dashboard creation, no research creates and tests a dashboard using scientific techniques. This study develops and demonstrates an empirical approach to dashboard metric selection. In a fast moving consumer goods category, this research selects leading indicators for national-brand and store-brand sales and revenue premium performance from 99 brand-specific and relative-to-competition variables including price, brand equity, usage occasions, and multiple measures of awareness, trial/usage, purchase intent, and liking/satisfaction. Plotting impact size and wear-in time reveals that different kinds of variables predict sales at distinct lead times, which implies that managerial action may be taken to turn the metrics around before performance itself declines.