• Korean Journal of Remote Sensing
• /
• v.32 no.1
• /
• pp.49-60
• /
• 2016

This paper presents a set of methods to evaluate the image quality of smartphone cameras as compared with that of a DSLR camera. In recent years, smartphone cameras have been used broadly for many purposes. As the performance of smartphone cameras has been enhanced considerably, they can be considered to be used for precise mapping instead of metric cameras. To evaluate the possibility, we tested the quality of one DSLR camera and 3 smartphone cameras. In the first step, we compare the amount of lens distortions inherent in each camera using camera calibration sheet images. Then, we acquired target sheet images, extracted reference lines from them and evaluated the geometric quality of smartphone cameras based on the amount of errors occurring in fitting a straight line to observed points. In addition, we present a method to evaluate the radiometric quality of the images taken by each camera based on planar fitting errors. Also, we propose a method to quantify the geometric quality of the selected camera using edge displacements observed in target sheet images. The experimental results show that the geometric and radiometric qualities of smartphone cameras are comparable to those of a DSLR camera except lens distortion parameters.

• Journal of Broadcast Engineering
• /
• v.24 no.2
• /
• pp.281-291
• /
• 2019

Depth from defocus estimates the 3D depth by using a phenomenon in which the object in the focal plane of the camera forms a clear image but the object away from the focal plane produces a blurred image. In this paper, algorithms are studied to estimate 3D depth by analyzing the degree of blur of the image taken with a single camera. The optimized object range was obtained by 3D depth estimation derived from depth from defocus using one image of a single camera or two images of different focus of a single camera. For depth estimation using one image, the best performance was achieved using a focal length of 250 mm for both smartphone and DSLR cameras. The depth estimation using two images showed the best 3D depth estimation range when the focal length was set to 150 mm and 250 mm for smartphone camera images and 200 mm and 300 mm for DSLR camera images.

• The Journal of the Korea Contents Association
• /
• v.12 no.5
• /
• pp.81-90
• /
• 2012

Since the Canon EOS 5D Mark II with which the Full HD video shooting is possible was launched in 2008, the utilization of the DSLR cameras has been increasing in the video production field. In this thesis, the shortages and advantages of the video functions that the 5D Mark II cameras have will be analysed and they will be compared with the RED cameras that are most widely used in the video production field today. Through this, the utilization of the DSLR camera in the film production field will be investigated. The DSLR camera has the advantage of having good clear picture since it uses the image sensor of big size, and of being able to utilize the various lenses of good quality, and is small in size and light in weight compared to the conventional HD cameras. Although, there are some limitations that there are parts to be improved such as the sound recording problems and development of various additional equipments, the excellent usage that the DLSR cameras have is presenting a new possibility for the film production.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2010.06a
• /
• pp.137-144
• /
• 2010

Ground digital image data obtained by using DSLR camera can be used to the ground photogrammetry and spatial modeling. Intensity of each pixel in digital video images is the most important parameter to generate digital image. Therefore, it is needed to estimate the parameters and spectral characteristics of digital cameras in order to take more definite intensity data. In this study, using the Sony DSC-F828 DSLR camera, seven digital images are obtained by the continuous shooting. (frame rate, 0.38 seconds). And then extract the value of the intensity from RGB band of each digital color photographs to confirm difference of intensity between frames. The purpose of this study is to confirm spectral characteristics and changes and to estimate correlation through the analysis of statistical in each pixel of R, G, B band.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.3
• /
• pp.1341-1349
• /
• 2011

This research is focused on an analysis on the structure of RAW image file and the development of a RAW image file viewer for an embedded device. Recently, several RAW image file formats are being used for saving and displaying the images created by various DSLR cameras, and the necessity of handing RAW images in mobile multimedia devices is increasing. For the development of RAW image decoding/encoding library applicable to WinCE-based embedded devices viewer, an analysis of RAW image file formats, such as CRW, CR2, PEF, NEF, MRW, have been performed because their formats are not released in public. By using the library, the analysis software which can extract RAW image data, 2~3 JPEG image files and other informations such as the specification of a camera and various photographic parameters from RAW image files, were developped and a RAW image file viewer which can run in WinCE-based embedded devices. The experimental result has shown that the viewer could encode and decode RAW image files successfully and it took approximately 10secs to load them to the screen in S3C6410 based embedded platform. The outcomes of this research cloud be a good information and solution to multimedia application developers.

• Imaging Science in Dentistry
• /
• v.54 no.1
• /
• pp.43-48
• /
• 2024

Purpose: Oral hygiene, maintained through plaque control, helps prevent periodontal disease and dental caries. This study was conducted to examine the accuracy of plaque detection with an intraoral scanner(IOS) compared to images captured with an optical camera. Materials and Methods: To examine the effect of color tone, artificial tooth resin samples were stained red, blue, and green, after which images were acquired with a digital single-lens reflex (DSLR) camera and an IOS device. Stained surface ratios were then determined and compared. Additionally, the deviation rate of the IOS relative to the DSLR camera was computed for each color. In the clinical study, following plaque staining with red disclosing solution, the staining was captured by the DSLR and IOS devices, and the stained area on each image was measured. Results: The stained surface ratios did not differ significantly between DSLR and IOS images for any color group. Additionally, the deviation rate did not vary significantly across colors. In the clinical test, the stained plaque appeared slightly lighter in color, and the delineation of the stained areas less distinct, on the IOS compared to the DSLR images. However, the stained surface ratio was significantly higher in the IOS than in the DSLR group. Conclusion: When employing IOS with dental plaque staining, the impact of color was minimal, suggesting that the traditional red stain remains suitable for plaque detection. IOS images appeared relatively blurred and enlarged relative to the true state of the teeth, due to inferior sharpness compared to camera images.

• Structural Engineering and Mechanics
• /
• v.69 no.4
• /
• pp.467-477
• /
• 2019

Digital image correlation (DIC) is now a popular and extensively used full-field metrology technique. In general, DIC is performed by using a turnkey solution offered by various manufacturers of DIC. In this paper, a simple and economical set-up for DIC is proposed which uses easily accessible digital single-lens reflex (DSLR) camera rather than industrial couple-charged device (CCD) cameras. The paper gives a description of aspects of carrying a DIC experiment which includes experimental set-up, specimen preparation, image acquisition and analysis. The details provided here will be helpful to carry DIC experiments without specialized DIC testing rig. To validate the responses obtained from proposed DIC set-up, tension and fatigue tests on specimens made of IS 2062 Gr. E300 steel are determined. Tensile parameters for a flat specimen and stress intensity factor for an eccentrically-loaded single edge notch tension specimen are evaluated from results of DIC experiment. Results obtained from proposed DIC experiments are compared with those obtained from conventional methods and are found to be in close agreement. It is also noted that the high resolution of DSLR allows the use of proposed approach for fracture characterization which could not be carried out with a typical turnkey DIC solution employing a camera of 2MP resolution.

• Journal of the Korean earth science society
• /
• v.38 no.5
• /
• pp.323-332
• /
• 2017

The Digital Single Lens Reflex (DSLR) camera combined with a small aperture telescope is an efficient equipment for an astronomy-related lab exercise. This paper compares the different photometry softwares to provide insights on using the GUI-based photometry tool to the conventional command-line based photometry tool. The magnitude of the same point source measured within the aperture is consistent regardless of the software used although the background estimation, partial pixel treatment, and error estimation are slightly different. In a crowded field image where the aperture photometry is less reliable, the aperture photometry with varying aperture size is useful to see the qualitative trend for the magnitude. Due to the variation in ISO settings and the color dependence on the RGB Bayer system, an initial uncertainty of ~0.15mag is expected to be embedded in the magnitude derived from the DSLR images.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.24 no.4
• /
• pp.424-429
• /
• 2014

In this paper, an image-based luminance measurement system(LMS) is proposed to measure the luminance of outdoor signboards. We design the LMS that can improve disadvantages of efficiency of the point-luminance meter and portability of face-luminance meter using the image of DSLR camera and print out the luminance value by using the proposed luminance analysis algorithm in real time. Outdoor signboards have various size and shape, and are also installed on the various place. Luminance of the signboard is influenced by measurement location, angle, color, etc. Therefore, we measure the change of luminance value in accordance with measurement location for accurate luminance measurement and then consider the luminance value according to the measurement distance. We obtain a numerical relation between luminance value and measurement location. The proposed LMS is verified through comparative experiment with point-luminance meter.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.38 no.2
• /
• pp.109-121
• /
• 2020

Depth calculation of objects in a scene from images is one of the most studied processes in the fields of image processing, computer vision, and photogrammetry. Conventionally, depth is calculated using a pair of overlapped images captured at different view points. However, there have been studies to calculate depths from a single image. Theoretically, it is known to be possible to calculate depth using the diameter of CoC (Circle of Confusion) caused by defocus under the assumption of a thin lens model. Thus, this study aims to verify the validity of the thin lens model to calculate depth from edge blur amount which corresponds to the radius of CoC. For this study, a commercially available DSLR (Digital Single Lens Reflex) camera was used to capture a set of target sheets which had different edge contrasts. In order to find out the pattern of the variations of edge blur against varying combination of FD (Focusing Distance) and OD (Object Distance), the camera was set to varying FD and target sheet images were captured at varying OD under each FD. Then, the edge blur and edge displacement were estimated from edge slope profiles using a brute-force method. The experimental results show that the pattern of the variations of edge blur observed in the target images was apart from their corresponding theoretical amounts derived under the thin lens assumption but can still be utilized to calculate depth from a single image for the cases similar to the limited conditions experimented under which the tendency between FD and OD is manifest.