• Journal of Mechanical Science and Technology
• /
• 제18권8호
• /
• pp.1451-1460
• /
• 2004

A two-stroke Schnurle-type gasoline engine was modified to enable compression-ignition in both the port fuel injection and the in-cylinder direct injection. Using the engine, examinations of compression-ignition operation and engine performance tests were carried out. The amount of the residual gas and the in-cylinder mixture conditions were controlled by varying the valve angle rate of the exhaust valve (VAR) and the injection timing for direct injection conditions. It was found that the direct injection system is superior to the port injection system in terms of exhaust gas emissions and thermal efficiency, and that almost the same operational region of compression-ignition at medium speeds and loads was attained. Some interesting combustion characteristics, such as a shorter combustion period in higher engine speed conditions, and factors for the onset of compression-ignition were also examined.

• 한국자동차공학회논문집
• /
• 제16권2호
• /
• pp.158-165
• /
• 2008

The combustion and exhaust emissions characteristics of a liquefied petroleum gas-di-methyl ether compression ignition engine with a variable valve timing device were investigated under various liquefied petroleum gas injection timing conditions. Liquefied petroleum gas was used as the main fuel and was injected directly into the combustion chamber. Di-methyl ether was used as an ignition promoter and was injected into the intake port. Different liquefied petroleum gas injection timings were tested to verify the effects of the mixture homogeneity on the combustion and exhaust emission characteristics of the liquefied petroleum gas-di-methyl ether compression ignition engine. The average charge temperature was calculated to analyze the emission formation. The ringing intensity was used for analysis of knock characteristics. The combustion and exhaust emission characteristics differed significantly depending on the liquefied petroleum gas injection and intake valve open timings. The CO emission increased as the intake valve open and liquefied petroleum gas injection timings were retarded. However, the particulate matter emission decreased and the nitrogen oxide emission increased as the intake valve open timing was retarded in the diffusion combustion regime. Finally, the combustion efficiency decreased as the intake valve open and liquefied petroleum gas injection timings were retarded.

• 한국자동차공학회논문집
• /
• 제7권7호
• /
• pp.104-112
• /
• 1999

An experimental study for reducing the exhaust hydrocarbon emission at spark ignition engine using timed secondary air injection is carried out . In this study, secondary air injection timings and durations are controlled to decrease the hydrocarbon emission and to increase exhaust gas temperature at cold and warm-up engine conditions. The hydrocarbon reduction rate and exhaust gas temperature are compared between timed secondary air injection and continuous air injection. The optimum secondary air injection timing for reducing the hydrocarbon emission is at the exhaust valve open timing. At some engine conditions , the hydrocarbon emissions are decreased to 10% of engine raw values and exhaust gas temperatures increase by 20$0^{\circ}C$ with times secondary air injection . Timed secondary air injection has more hydrocarbon reduction rate that continuous secondary air injection except some engine conditions.

• 한국자동차공학회논문집
• /
• 제2권6호
• /
• pp.76-86
• /
• 1994

Combustion of diesel engine depends on the mixing of air and evaporating fuel during ignition delay greatly. Variation of air-fuel mixing rate and ignition delay for engine operating condition causes difference of combustion, performance and exhaust emissions. This study is investigated in a turbocharged diesel engine of IDI swirl chamber type. In the results, As injection timing is advanced until $12.6^{\circ}$ BTC, ignition delay decreases. NOx concentration and smoke level in exhaust gas increases for advanced injection timing Ignition delay, combustion period, pressure rise rate and exhaust gas temperature are increased with increasing engine speed. And ignition delay at high load is more decreased than that at low load. Ignition delay and combustion period are decreased with increasing intake pressure. Power increases, temperature and CO, NOx concentration in exhaust gas decreases as intake pressure increases. With increasing load, ignition delay is decreased and combustion period, motoring pressure are increased.

• 한국산학기술학회논문지
• /
• 제22권6호
• /
• pp.75-82
• /
• 2021

디젤엔진의 열효율을 높이면서 NOx와 PM을 효과적으로 저감시키기 위해 HCCI(Homogeneous Charge Compression Ignition), PCCI(Premixed Charge Compression Ignition), RCCI(Reactivity Controlled Compression Ignition) 등의 저온연소(LTC: Low Temperature Combustion)전략이 개발되어 왔다. 본 연구에서는 저반응성 연료로는 가솔린을 사용하고 고반응성 연료로는 디젤을 사용하는 RCCI 엔진에서 고반응성 연료인 디젤연료의 분사 시기와 이단 분사비율이 성능 및 배출가스에 미치는 영향을 수치해석을 통하여 파악하고자 하였다. 이단 분사 시 첫 번째 분사시기가 너무 진각되면 연소가 느려지면서 연소온도가 낮아져 연소성능이 저하되고 HC, CO가 증가한다. 대략 -60°ATDC 의 분사시기가 연소성능, 배출가스 및 최대압력상승률을 고려하였을 때 가장 최적의 분사시기라고 판단된다. 이단 분사 시 두 번째 분사시기를 변경하였을 때 연소성능 및 배출가스, 최대압력상승률 등을 고려하면 대략 -30°ATDC 부근에서 최적인 것으로 판단된다. 이단 분사 시 분사량 비율은 첫 번째 분사량을 60% 정도로 하였을 때 최적의 결과를 얻었다. 마지막으로 단일 분사보다는 이단 분사한 경우 연소성능 및 배출가스 부분에서 더 효과적인 것으로 판단된다.

• 동력기계공학회지
• /
• 제22권1호
• /
• pp.56-63
• /
• 2018

After the recent fabrication of diesel vehicle exhaust gas by Volkswagen, nitrogen oxides ($NO_x$) and particulate matter (PM) are drawing attention as representative pollutants included in exhaust gas. When gasoline and diesel fuels are combusted through direct injection into a combustion chamber at high pressure, PM emission is actually increased. To find a solution to this problem, a basic study was conducted to derive an optimized variable for combustion of compressed natural gas (CNG) by applying CNG, acknowledged as a clean fuel, to direct injection system. The essence of this study is in the introduction of a radical ignition technology for compressed natural gas (RI-CNG) in a sub-chamber type engine. The direct injection system was applied to a sub-chamber to remove residual gas from previous combustion cycle. In addition, optimal mixer distribution was achieved by precisely setting ignition timing based on fuel injection timing and excess air ratio.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 제26회 KOSCO SYMPOSIUM 논문집
• /
• pp.27-32
• /
• 2003

Diesel-Fueled HCCI(Homogeneous Charge Compression Ignition) Engine is an advanced combustion process explained as a premixed charge of diesel fuel and air is admitted into the cylinder and compression ignited. It has possibility to reduce NOx by spontaneous auto-ignition at multiple points that allows very lean combustion resulting in low combustion temperatures. Also PM could be reduced by the premixed combustion and no fuel-rich zones. But HCCI couldn't be realized because of the difficulties in vaporizing the diesel, control of combustion phase directly. To solve these problems, new fuel injection strategy, explained as the pilot fuel injection to promote ignition near TDC following the main fuel injection at the extremely advanced timing, is applied during the compression ratio is varied from 18.9:1 to 27.7:1 This is not a pilot fuel to promote the ignition but also the direct control method of the combustion phase. Experimental result shows the pilot fuel injection promote the ignition and the compression ignition of the HCCI engine is achieved as compression ratio becomes higher. Also there is an optimal pilot fuel injection timing for the HCCI combustion. NOx is reduced more than 90% compared to DI-Diesel case but PM and THC emission needs more investigation.

• 동력기계공학회지
• /
• 제19권4호
• /
• pp.56-68
• /
• 2015

Liquefied petroleum gas and compressed natural gas haven been regarded as promising alternative fuels because of no smoke, and they are also clean fuel for spark-ignited engine. In spark-ignited direct-injection engine, direct injection technology can increase engine volumetric efficiency significantly and also reduce necessity of throttle valve. This study designed combustion chamber equipped with visualization system. To improve ignition probability, the study designed to help three types of impingement-walls to form mixture. In doing so, LPG CNG-air mixture could be easily formed after spray-wall impingement and ignition probability increased too. The results of this study could contribute as basic resources of spark-ignited direct injection LPG and CNG engine design and optimization extensively.

• 에너지공학
• /
• 제19권1호
• /
• pp.32-38
• /
• 2010

The objective of the research was to study the effects a Miller cycle. The engine was dedicated to natural gas usage by modifying pistons, fuel system and ignition systems. The engine was installed on a dynamometer and attached with various sensors and controllers. Intake valve timing, engine speed, load, injection timing and ignition timing are main parameters. Miller Cycle without supercharging can increase brake thermal efficiency 1.08% and reduce brake specific fuel consumption 4.58%. The injection timing must be synchronous with valve timing, speed and load to control the performances, emissions and knock margin. Throughout these tested speeds, original camshaft is recommended to obtain high volumetric efficiency.

• Environmental Engineering Research
• /
• 제22권3호
• /
• pp.294-301
• /
• 2017

This paper is based on experiments conducted on a stationary, four stroke, naturally aspirated air cooled, single cylinder compression ignition engine coupled with an electrical swinging field dynamometer. Instead of 100% diesel, 20% Jatropha oil methyl ester with 80% diesel blend was injected directly in engine beside 25% pre-mixed charge of diesel in mixing chamber and with 20% exhaust gas recirculation. The performance and emission characteristics are compared with conventional 100% diesel injection in main chamber. The blend with diesel premixed charge with and without exhaust gas recirculation yields in reduction of oxides of nitrogen and particulate matter. Adverse effects are reduction of brake thermal efficiency, increase of unburnt hydrocarbons (UBHC), carbon monoxide (CO) and specific energy consumption. UBHC and CO emissions are higher with Diesel Premixed Combustion Ignition (DPMCI) mode compared to compression ignition direct injection (CIDI) mode. Percentage increases in UBHC and CO emissions are 27% and 23.86%, respectively compared to CIDI mode. Oxides of nitrogen ($NO_x$) and soot emissions are lower and the percentage decrease with DPMCI mode are 32% and 33.73%, respectively compared to CIDI mode.