• 대한조선학회논문집
• /
• 제47권3호
• /
• pp.350-358
• /
• 2010

The present paper deals with the comparative study of resistance performance with refrigerated ice and synthetic ice according to the variation of hull form characteristics. The resistance test has been conducted in pack ice condition in each concentration condition. Stem angle has been chosen as main parameters for the variation of hull form characteristics. The correlation of performance between with the refrigerated ice and with the synthetic ice has been shown according to the variation for stem angles. The present study show the possibility of ice test in general towing tank with synthetic ice for the time-consuming research such as hull form optimization although that is confined in pack ice condition. The more parametric study for the properties of synthetic ice is expected to be conducted to have more close correspondence for the test results of refrigerated ice in near future.

• 한국항해학회지
• /
• 제18권4호
• /
• pp.23-31
• /
• 1994

A theoretical scaling was made in order to acquire the ice resistance of ships in level ice. Ice resistance of ice-breaker Ermak was calculated by Kashteljan eequation and it's model test results were compared with full-scale measurements. Atkins's ice number and Norman Jones's dimensionless numbers were investigated and discussed.

• 대한조선학회논문집
• /
• 제58권3호
• /
• pp.175-181
• /
• 2021

This study describes the model tests in ice according to the frictional coefficient of an ice-breaking ship and the change in ice resistance by the analysis method for each component of ice resistances. The target vessel is a 90K DWT ice-breaking tanker capable of operating in ARC7 ice conditions in the Arctic Ocean, and twin POD propellers are fitted. The hull was specially painted with four different frictional coefficients on the same ship model. The total ice resistance can be separated by ice breaking, ice buoyancy, ice clearing resistances through the tests in level ice, pre-sawn ice and creep test in pre-sawn ice under sea ice thickness of 1.2 m and 1.7 m. Ice resistance was analyzed by correcting the thickness and bending strength of model ice by the ITTC correction method. As the frictional coefficient between the hull and ice increases, ice buoyancy and clearing resistances increase significantly. When the surface of the hull is rough, it is considered that the broken ice pieces do not slip easily to the side, resulting in an increase in ice buoyancy resistance. Also, the frictional coefficient was found to have a great influence on the ice clearing resistance as the ice thickness became thicker.

• 한국해양공학회지
• /
• 제22권5호
• /
• pp.83-86
• /
• 2008

This paper deals with the experimental works for the correlations of ice resistance for icebreaker with synthetic(model) ice in general towing tank and with refrigerated ice in ice tank. In order to find out the correlation, the density variation is mainly focused in the present study. The model of Terry-Fox ice breaker has been used for the present correlation study because many data are available to be compared. According to the increase of density, the correlation becomes better quantitatively as well as qualitatively. Other parametric studies such as an ice size, a friction coefficient, a bending moment, etc., are also expected to be carried out to have better correlation in a near future. This research could be the basis for the possibility of resistance test using a synthetic ice in a general towing tank instead of an expensive ice tank.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제7권4호
• /
• pp.699-707
• /
• 2015

The ice-resistance estimation technique for icebreaking ships had been studied intensively over recent years to meet the needs of designing Arctic vessels. Before testing in the ice model basin, the estimation of a ship's ice resistance with high reliability is very important to decide the delivered power necessary for level ice operation. The main idea of previous studies came from several empirical formulas, such as Poznyak and Ionov (1981), Enkvist (1972) and Shimansky (1938) methods, in which ice resistance components such as icebreaking, buoyancy and clearing resistances were represented by the integral equations along the Design Load Water Line (DLWL). The current study proposes a few modified methods not only considering the DLWL shape, but also the hull shape under the DLWL. In the proposed methodology, the DLWL shape for icebreaking resistance and the hull shape under the DLWL for buoyancy and clearing resistances can be directly considered in the calculation. Especially, when calculating clearing resistance, the flow pattern of ice particles under the DLWL of ship is assumed to be in accordance with the ice flow observed during ice model testing. This paper also deals with application examples for a few ship designs and its ice model testing programs at the AARC ice model basin. From the comparison of results of the model test and the estimation, the reliability of this estimation technique has been discussed.

• 대한조선학회논문집
• /
• 제46권5호
• /
• pp.471-478
• /
• 2009

The present paper deals with characteristics of resistance performance according to the variation of synthetic ice thickness and hull form. The resistance test has been conducted with pack ice condition in Pusan National University towing tank. Stem angle has been chosen as main parameters for the variation of hull form characteristics, which is the most important factor especially in icebreaking cargo vessel. The serial comparisons of resistance test have been done with the variation of hull form parameter as well as with the different thickness of synthetic ice. The different trend of resistance performances with increasing of stem angle has been shown at each synthetic ice thickness. The present test results is expected to be confirmed by comparing the test results in ice tank in the near future.

• 대한조선학회논문집
• /
• 제43권2호
• /
• pp.147-155
• /
• 2006

Ice resistance estimation equations based on model tests and full-scale sea trial data from many previous research articles are studied. Measured ice resistance data and its empirical/semi-empirical estimation equations are summarized in common format and are compared with each other, considering three ship categories, i.e, icebreakers, tug/supply vessels, ice-strengthened cargo vessels. The most suitable estimation methods or prediction equations are recommended based on this ice resistance data analysis.

• 한국기계기술학회지
• /
• 제13권4호
• /
• pp.109-115
• /
• 2011

The ice tank is important facility to check the performance of the ship and offshore in ice condition before the construction. MOERI(Maritime & Ocean Engineering Research Institute) constructed ice model basin on the end of 2010. The ice technology to know the phenomena of ice near the ship and to estimate power of the ship in model scale is the main characteristic of the ice model basin. To achieve this goal in one ice sheet, making of test plan and feasibility check of test possibility have to review in the beginning stage of the every test. This paper describes the number of maximum resistance and self propulsion test in a sheet of level ice and proposes the methodology to optimize pack ice, rubble ice, brash ice and ice ridge test in MOERI ice tank. The feasibility of free running test to know maneuvering performance in ice field and some specific idea to measuring ice thickness and ice ridge shape was proposed.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제12권1호
• /
• pp.414-427
• /
• 2020

The finite element method is used to simulate the navigation of an ice-area bulk carrier in broken ice fields. The ice material is defined as elastic, and the simulations are accomplished at four model speeds and three ice concentrations. The movements of ice floes in the simulation are consistent with those in the model test, and the percentage deviation of the numerical ice resistance from the ice resistance in the model test can be controlled to be less than 15 %. The key characteristics of ice loads, including the average ice loads, extreme ice loads, and characteristic frequency, are analyzed thoroughly in a comprehensive manner. Moreover, the effects of sailing speed and ice concentration on the ice loads are analyzed. In particular, the stress distribution of ice floes is presented to help understand how model speed and concentration affect the ice loads. The "ice pressure" phenomenon is observed at 90 % ice concentration, and it is realistically reflected both in the time―and frequency―domain ice force curves.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제10권3호
• /
• pp.413-420
• /
• 2018

This paper documents the result of a preliminary analysis on the influence of hull-ice friction coefficient on model resistance and power predictions and their correlation to full-scale measurements. The study is based on previous model-scale/full-scale correlations performed on the National Research Council - Ocean, Coastal, and River Engineering Research Center's (NRC/OCRE-RC) model test data. There are two objectives for the current study: (1) to validate NRC/OCRE-RC's modeling standards in regarding to its practice of specifying a CFC (Correlation Friction Coefficient) of 0.05 for all its ship models; and (2) to develop a correction methodology for its resistance and propulsion predictions when the model is prepared with an ice friction coefficient slightly deviated from the CFC of 0.05. The mean CFC of 0.056 and 0.050 for perfect correlation as computed from the resistance and power analysis, respectively, have justified NRC/OCRE-RC's selection of 0.05 for the CFC of all its models. Furthermore, a procedure for minor friction corrections is developed.